-
Product
Infiniium MXR B-Series Oscilloscope: 4 GHz, 4 Channels
MXR404B
Oscilloscope
MXR404B Infiniium MXR B-Series, 4 GHz on all 4 channels, option to integrate up to 8 instruments in one, hardware accelerated plotting, and fully upgradeable , including up to 6 GHz and 8 channels.
-
Product
48 Channel Isolated Digital Input/Output Module
DP-VME-3078
-
DP-VME-3078 is a 48 Channel Isolated Digital Input Output Module. This module provides 48 input / interrupt channels and 48 digital output channels with isolation. The 48 channel inputs are divided into 12 groups, each group consisting of 4 channels and 1 common GND .The 48 output channels are divided into 6 groups, each group consisting of 8 channels and a common GND.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 1k
40-265-206
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Clamp Meters
-
Clamp meter is a rugged high end AC clamp meter. With a UL listed safety rating of CAT IV 600V / CAT III 1000V, this clamp meter is built to get the tough jobs done.
-
Product
Vector Signal Generator
SMM100A
Vector Signal Generator
The R&S®SMM100A vector signal generator provides remarkably good RF characteristics across the entire frequency range from 100 kHz to 44 GHz. The instrument covers the bands below 6 GHz used by existing wirelessstandards as well as the newly defined bands for 5G NR FR1 and Wi-Fi 6E up to 7.125 GHz and the 5G NR FR2 bands up to 44 GHz.The internal baseband generator in the R&S®SMM100A supports a maximum RF modulation bandwidth of 1 GHz. Digitally modulated broadband signals can thus be generated as required by the prevalent wireless standards. The R&S®SMM100A is well prepared for future bandwidth requirements.
-
Product
LXI Microwave Multiplexer, SP6T, 9-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-509
Microwave Multiplexer
Our 60-800-509 is a 9 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Residential Combustion Analyzer w/ AC509 Carrying Case
C161C
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C161 Residential Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and now adds a heat exchanger test. Prints to optional printer. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
PXI-5412, 20 MHz Bandwidth, 1-Channel, 14-Bit PXI Waveform Generator
779176-02
Waveform Generator
20 MHz Bandwidth, 1-Channel, 14-Bit PXI Waveform Generator - The PXI‑5412 is a 20 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms and standard functions including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms.
-
Product
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 60 V, 0 A, 6 A
T3PS16006
Power Supply
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 60 V, 0 A, 6 A.
-
Product
NIM and CAMAC Power Supply
UEP 15
-
The UEP 15 is a plug in power supply for use in UEN 04 bin or for powering every non-powered extant NIM bin. The UEP 15 features all 6 voltages, stabilized by adjustable monolithic voltage regulators. Outputs are ported using a rear mounted NIM connector with a standard NIM pin out.
-
Product
Fused Test Probes with Silicone Test Leads
AL-57FL
-
Standard Electric Works Co., Ltd
● AL-57FL is an ideal tool which shows the indication of live voltage even with blown fuse.● 2 replaceable fast-acting fuses are built-in. The specs of the fuses are 1000V, 11A with internal rating of 20kA AC/DC.● Provide additional testing protection.● Help to prevent a possible mis-indication when there is voltage present.● CAT III 1000V, CAT IV 600V, 10A with protective cover.● 2mm probe tips, removable 4mm brass caged banana probe tips are also included.● Include High-quality silicone test leads, 1.5 meter long.● Wipe the fused test probes and silicone test leads periodically with a damp cloth and detergent. Do not use abrasives or solvents.● Operating temperature: -20 °C to +50 °C (-5 °F to 120 °F)● One year warranty● Can't be used on current mode with blown fuse.● Rating : EN 61010-031 CAT Ⅲ 1kV 10A / CAT Ⅳ 600V 10A
-
Product
USB Power Sensor, 9 kHz to 6 GHz
U2004A
Power Sensor
Fast and simple setup with plug-and-play USB connectivity. Eliminates the need for a separate power meter.
-
Product
Hydrometer
DMA-35
-
Explorer Technology Group (ETG)
Reads specific gravity and temperature. Package includes; a custom carry case, operating instructions and a 6 month limited warranty. The DMA-35n will be configured to read the specific gravity of battery acid at 77F/77F compensation and fluid temperature in degrees Fahrenheit as standard.
-
Product
Mini-ITX SBC With Intel® Celeron® Processor N3350 & Pentium® Processor N4200, VGA, HDMI, LVDS, USB 3.0, PCI Express Mini Card Slot, M.2, And HD Audio
MANO310
-
*Intel® Celeron® N3350 & Pentium® N4200 (optional)*2 DDR3L SO-DIMM for up to 8GB of memory*1 PCI Express Mini Card slot and PCIe x1*4 USB 3.0 and 2 USB 2.0*1 SATA-600, 1 M.2 and 1 SDXC slot*6 COM supported*12 to 24 VDC*VGA, HDMI and LVDS with triple-view supported
-
Product
Vibration Sensor
ENVIROMUX-VSS
-
For registering movement and shocks. Adjustable sensitivity. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Regulatory approvals: RoHS.
-
Product
PXIe-5645, 6 GHz, 80 MHz Bandwidth, RF and Baseband PXI Vector Signal Transceiver
782377-01
Vector Signal Transceiver
6 GHz, 80 MHz Bandwidth, RF and Baseband PXI Vector Signal Transceiver—The PXIe‑5645 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5645 offers the flexibility of a software defined radio architecture with RF instrument class performance. The PXIe‑5645 features a high-performance, differential or single-ended baseband I/Q interface. This interface allows the PXIe‑5645 to address many additional applications, such as testing both the upconverted RF and downconverted baseband signals of a device with a single instrument.
-
Product
Cryogenic Hygrometer
CR - 1A
-
Buck Research Instruments, LLC
The CR-1A is a high performance, cryogenically cooled hygrometer. CR-1 instruments have been routinely used aboard NASA aircraft and elsewhere for years. The CR-1A is a miniaturized version of the original CR-1, and uses a much smaller LN2 dewar. Operating time per filling of LN2 ranges from 6 to 8 hours, depending on the dew points being measured.
-
Product
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
540265010207
Cable Assembly
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
-
Product
Interface
3508 MMS ECM
Interface
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
HDMI/DVI Receivers
-
HDMI® receivers and DVI receivers remain in high demand for professional, consumer, and automotive video applications, with HDMI nodes constantly increasing. Analog Devices offers a range of HDMI/DVI receivers that enable high quality conversion of digital video data to formats such as HDMI, MIPI, and TTL. Applications include video distribution, gaming, and HDMI/DVI consumer device connectivity for automotive infotainment systems. Our portfolio of HDMI receivers and DVI receivers offers competitive advantages such as automotive qualification, superior HDMI/DVI equalizer performance, comprehensive audio extraction, and small packages (6 mm × 6 mm, 0.5 mm pitch BGA).
-
Product
Bench Digital Multimeter, Calibrated D & U, 1 kV, 10 A, 3.8 Digit
72-1015 CAL DU
-
The 72-1015 CAL DU from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
Digital Insulation Mult-Meter
8010 IN
-
Standard Electric Works Co., Ltd
● Microprocessor controlled.● Four insulation test voltages (DC) : 125V, 250V, 500V, 1000V● The maximum insulation measurement range is 200G ohm @1000V.● 1mA test current on insulation test at nominal voltage.● With a hand strap for easier holding.● Large LCD (78 × 67mm)● Auto-ranging.● Bar-graph indication.● Backlight function.● REL(Auto-null) function.● Auto AC/DC voltmeter.● Capacitor test.● Auto-test stop & smart hold.● Supplied with high quality test leads.● Safety standard : EN 61010-1 CAT III 600V IEC 61557-1 IEC 61557-2 EN 61326-1
-
Product
COM Express Compact Size Type 6 Module with Intel Pentium, Celeron N3000 Series and Atom x5 E8000 SoC (formerly codename: Braswell)
cExpress-BW
Computer on Module
ADLINK cExpress-BW provides two DDI channels (with up to 4K resolution) and one eDP or DDI3 channel supporting three independent displays, enabling it to drive multiple HD screens without the need for a discrete graphics card. In addition, LVDS is optionally available to support next generation displays. The cExpress-BW offers up to five PCI Express lanes x1. A wide range of operating systems are supported, including Linux, Windows 7 and 8.1u, Windows Embedded Standard 7, Windows Embedded Industry 8.1 and VxWorks.
-
Product
PXI 4 Slot BRIC 180x8 1-Pole (6 sub-cards)
40-561A-021-180X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 6-Channel 10A Solid State SPST Switch
40-182-011
Switch Module
The 40-182-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI Dual 6 To 1 RF Multiplexer, 8GHz 50Ω SMA, Terminated
40-881A-002
Multiplexer Module
The 40-881A-002 is a dual 6 to 1 50Ω RF multiplexer with 8GHz bandwidth and automatic termination of unused signal channels. It is available as a single or dual MUX in one and two PXI slots respectively.
-
Product
32 Channel Charge-Discharge Module 6 V, 6.25 A
BT2204B
Charge-Discharge Module
The BT2204B is a 32-channel charge-discharge module 6 V, ± 6.25 A, for testing higher power prismatic and pouch cells as well as higher current cells.
-
Product
3U CompactPCI Serial Processor Blade with 6 COres/12 Thread Core i7 and Xeon Processor
MIC-330 Series
Processor Blade
MIC-330 is a 3U CompactPCI® serial processor blade with 6 cores/12 thread Core™ i7 and Xeon® processor and configured with Intel® CM246 PCH to support dual-channel 32GB DDR4-2666, up to 16GB on board memory for rugged applications, and another 16GB are available via the SO-DIMM socket for expansion.
-
Product
Standard Prod
121017/Colour
-
IEC 1010 Rating: 1000 Volts Cat III Double/Reinforced Insulation 30Amps Standard Colours: Black, Red Features: Standard 4mm socket to rear.
-
Product
PXI 8 Slot BRIC 132x8 2-pole (6 sub-cards)
40-562A-122-132X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
