Filter Results By:
Products
Applications
Manufacturers
Seismic Accelerometers
sense ground vibration.
See Also: Seismic, Seismometers, Seismic Arrays, Earthquake
-
product
High Sensitivity Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
The piezoelectric accelerometers on this page are intended for the measurement of lowest vibrations. Typical fields of application include the monitoring of buildings, dams, bridges, oil platforms and pipelines. These sensors are often called seismic accelerometers because they are used to monitor construction activity, volcanoes and earthquakes. Their high sensitivity is achieved -unlike other high sensitivity accelerometers- by the sensing element itself and not by internal amplification. From this results highest resolution and lowest noise.
-
product
Triaxal Seismograph
BC 1313 TRIAXIAL SEISMOGRAPH
BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.
-
product
Accelerometer
EMIC offers many kinds of accelerometers available for various vibration measurements. They are a ultra small light weight accelerometer for highly precise measurement, a special tri-axial accelerometer for simultaneously measuring a vibration in three orthogonal axes, a large output accelerometer for measuring an earthquake and a suitable accelerometer for measuring and analyzing a building structure.
-
product
Accelerometers
Dytran accelerometers are used for product testing & development, structural monitoring, and industrial machinery health monitoring management. We offer a wide range of piezoelectric & VC MEMS sensors.
-
product
Accelerometers
Accelerometers measure linear acceleration. They can be also used for specific purposes such as inclination and vibration measurement. MEMS accelerometers embed several useful features for motion and acceleration detection, including free-fall, wakeup, single/double-tap recognition, activity/inactivity detection and 6D/4D orientation.
-
product
Dual Accelerometer
M6
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
product
Accelerometers
Honeywell Industrial Automation
Honeywell Sensotec Accelerometers are manufactured as standard, modified standard, and custom to provide the fastest possible delivery. Many units can be shipped from our extensive accelerometer stocking program within 24 hours. We offer a wide range of frequencies from DC to 6000 Hz and full ranges of 5 G to 2000 G. These units will survive overloads up to 500% (varies with model) and are also designed to cope with operating temperature between 100 and 500 degrees Fahrenheit.
-
product
Accelerometers
Monitran General Purpose Analysis Sensors are ideal for use with portable and on-line vibration analysers, providing the user with a complete spectrum of vibration intensity against frequency. Changes in this spectrum allow the user to determine the health of the machinery to which the sensor is attached. Most analysers will store the spectral values and monitor changes over a period of time, allowing prediction of expected component life and enabling efficient planning of maintenance schedules.
-
product
Seismic Signal Conditioners
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
product
Analog Seismic Sensors
Seismometers
Designed to yield the performance needed for scientific studies, our seismometers are used for monitoring long period (very low frequency) signals. These units are often used for earthquake monitoring and for triggering potential alerts during natural disasters such as tsunamis.
-
product
Advanced Seismic Source
GI-SOURCE
Sercel developed the GI-SOURCE to reduce and suppress the bubble oscillation from a single impulsive source to simplify processing. The GI-SOURCE impulsive source is based on the same technology as the GI-SOURCE but is different in that it has two independent air chambers within the same casing : the Generator (generating the primary pulse and creating the main bubble) and the Injector (injecting air inside the main bubble so that it collapses quickly).
-
product
Accelerometers
356A02
Sensitivity (10 %)10 mV/g1.02 mV/(m/s) Measurement Range:500 g pk4900 m/s pk Frequency Range: (5 %)1 to 5000 Hz1 to 5000 Hz Frequency Range: (10 %)0.5 to 6000 Hz0.5 to 6000 Hz Resonant Frequency:25 kHz 25 kHz Broadband Resolution (1)0.0005 grms 0.005 m/s rms Non-Linearity: (400 g, 3920 m/s)1 % 1 % Non-Linearity (500 g, 4900 m/s)2 % 2 % Transverse Sensitivity:5 % 5 %.
-
product
MEMS Accelerometer
SQ-XLD
The acceleration sensor module performs calibrated acceleration measurement with digital serial output. Using a USB or RS232 interface cable (sold separately), it functions as a self contained data acquisition system for 2 axis or 3 axis acceleration, tilt, and vibration measurement.
-
product
Accelerometers
An accelerometer is used in manufacturing machine maintenance to inspect equipment vibration. An accelerometer also is used in product testing to measure the vibration of various components.A triaxial accelerometer, also called a 3-axis accelerometer, provides measurements of the following parameters: vibration acceleration, vibration velocity and vibration displacement. In this way, vibration is measured and recorded with great precision.Most accelerometer products offered by PCE Instruments are portable devices. Many feature memory functionality so that readings can be stored and retrieved later for in-depth analysis. Some accelerometer models come with a manufacturer's calibration certificate. Some accelerometer models can be calibrated to ISO standards optionally for an additional fee.
-
product
High Temperature Accelerometer
CM362-7A
High Temperature Accelerometer, 650F (343 C) Top Exit Flexible Hardline Integral Cable 25 pC/g
-
product
Bandwidth-Controlled Seismic Source
eSource
Teledyne Bolt, Inc. has engineered a new type of airgun designed to reduce the potential impact of seismic acquisition operations on marine life while also delivering optimal bandwidth for subsurface imaging. eSource is designed to reduce the high-frequency components believed to have most potential for causing disturbance to marine life while retaining the low-frequency components critical to seismic exploration.
-
product
Accelerometers
ROGA-Instruments provides a broad range of accelerometers for General applications, Seismic measurements, High acceleration and shock, Light test objects, Triaxial measurements and Industrial applications.
-
product
GEOPHYSICS, SEISMIC, and ATMOSPHERICS RESEARCH RECEIVER
Type RAS-1
Called the RAS-1, the receiver is designed for ultra low and very low frequency scientific research work, including the exploration of low frequency emissions due to seismic and earth-quake activity, study of atmospheric phenomenon such as "whistlers", and low frequency Sudden Ionospheric Disturbance (SID) and electromagnetics phenomenon. The RAS-1 will receive signals from under 200 Hz. To over 250 KHz in both narrow bandwidth modes as well as broad badnwidth reception.
-
product
Quantum Accelerometer
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
product
Seismic interpretation Software
GeoTomCG
GeoTomCG can process crosshole or VSP seismic or radar data. The display shows calculated radar velocities. High velocity zone at depth of 27 m is caused by an abandoned mine. Other zones of contrasting velocities are geological features. S and R indicate source and receiver positions, respectively.
-
product
New Generation Marine Seismic Recorder
Seal 428
The Seal 428 is the new large capacity and high-resolution seismic data acquisition system designed for marine towed streamers acquisition. It derives its high reliability and versatility from SERCEL’s extensive experience in cable telemetry systems and from the use of the most advanced electronics and workstation technology.
-
product
Seismic Triggers
Offers a powerhouse of strong features for shutdown of industrial devices at the onset of a strong earthquake.
-
product
Universal Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
There are models with charge output and with IEPE compatible voltage output. The transducers of KS series have a shear type sensing element making them less susceptible to thermal transients and base strain. The accelerometers of KD series have a compression type sensing element combining rugged design, precision and low cost.
-
product
Seismic interpretation Software Winsism
Winsism
WinSism enables all typical operations for refraction processing including: first break picking, trace phantoming, true velocity, velocity computation, intercept time method, delay method, GRM method. It can also import all usual seismic file format as well as export in raster or vector output.
-
product
Triaxial Wireless Accelerometer
Our Triaxial Wireless Accelerometer is a vibration sensor specially designed for vibration analysis with universal compatibility. WiSER 3x is a wifi accelerometer that sends 3 axis vibration data + 1 additional channel simultaneously to any data collector in the market. Also, WiSER 3x is a wireless ultra-low noise accelerometer with 15 kHz bandwidth that exceeds the characteristics above all of most conventional accelerometers.
-
product
Long Life Seismic Energy Source
1500LL
Excellent low frequency content. Using heavy-duty cluster spreader bars cluster elements in excess of 1,000 cubic inches possible without sacrificing peak output
-
product
Accelerometer & Platform Test Bench
mS 1115
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
product
High-Resolution Seismic Recording System
DAQlink5
DAQlink 5 is the fifth generation of portable seismograph systems. It can be configured as a stand-alone monitoring system, a refraction system, or a distributed seismic reflection system.
-
product
General Purpose Single Axis Accelerometers
Motion of a rigid body can be characterized within six degrees of freedom. Providing mechanical excitation to simulate this motion as may be encountered in the real world can entail a variety of test machines. There are various pound/force vibration shakers for structural testing. Regardless of the apparatus, the goal is always to ensure that the product under test can adequately perform, and reliably survive, in the environment in which it will be deployed, or to which it will be exposed during transport. PCB® accelerometers provide the measurement signals needed to control the vibratory input and to analyze the product’s reaction to such testing.
-
product
Seismic interpretation Software
Visual-Sunt
This program is a graphical interface for Windows® of the SUNT program, the 32 bits Windows® version of the SU (Seismic UNIX) freeware, the software for the data processing of “Centre of Wave Phenomena”.
