Plugs
A male connector.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Portable GPU empowered by NVIDIA RTX A500
Pocket AI (EGX-TBT-A500)
Pocket AI offers the ultimate in flexibility and reliability on the move. This portable, plug and play AI accelerator delivers a perfect power/performance balance from the NVIDIA RTX GPU. Pocket AI is the perfect device for AI developers, professional graphics users and embedded industrial applications for boosting productivity by improve the work efficiency.
-
product
Glow Plug Tester
7640
Peaceful Thriving Enterprise Co Ltd
The tester is able to help diagnosing the condition of glow plug without removing it from the engine. This tester is working for 12V system, tester can be energized by 12V vehicle battery directly.
-
product
AC Power Sources
BPS Series
AMETEK Programmable Power, Inc.
The BPS Series consists of multiple high power AC power systems that provide controlled AC output for ATE and product test applications. This high power AC test system covers a wide spectrum of AC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the BPS Series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the unit to its designated location (using included casters), plug it in, and the BPS Series is ready to work for you.
-
product
16-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2354A
The U2354A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2354A to simulate simultaneous analog input acquisition.
-
product
Cable Assembly, Receiver, 36", Mini Coax, 6 SMB Plugs
540093010207
Cable Assembly, Receiver, 36", Mini Coax, 6 SMB Plugs.
-
-
product
OLED Lifetime Test System
58131
The 58131 Lifetime Test System is designed specifically for the OLED industry. Model 58131 provides twoquadrant constant current (CC) and constant voltage (CV) stimulus to each OLED panel and acquires electrical and optical characteristics automatically. Two independent and isolated precision source-and-measure units (PMU) are incorporated in one modular card, which is capable of testing two OLED panels. Additional instrument cards are added to expand test capacity. Hot plug and play is a key feature of 58131. When a UUT fails or an instrument card needs to be replaced, 58131 does not have to be shutdown and testing continues for other UUTs. Hot plug and play obviates life test cycle restarts due to isolated faults and significantly improves life test efficiency. We firmly believe that hot plug and play capability should be mandatory for all lifetime test systems.
-
product
Mini Coax, Patchcord, Receiver, 36", Mini Coax, RG178BU Tan to SMA Plug
7-334178576-036
Mini Coax, Patchcord, Receiver, 36", Mini Coax, RG178BU Tan to SMA Plug.
-
product
48" Stacking Banana Plug Test Leads
146-P
These test leads feature stacking banana plug jacks, with extended 48" length. These are great for establishing connections to diagnostic test points, while allowing the connection to be tapped with other instruments...2 way connections. These feature high flexibility wire and standard 4mm size banana jacks. You will receive one red test lead and one black test lead. These test leads are compatible with Electronic Specialties 146 and 147 test lead kits.
-
product
Cable Assembly, Receiver, 20", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
540297010147
Cable Assembly, Receiver, 20", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
-
product
Plug-To-Plug Expando Jacket
For connecting boxes when the crush resistance of armor is not required.
-
product
BNC Twinax Connectors
BNC Twinax connector category has several part numbers, the majority are RoHS and REACH compliant. BNC Twinax connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC Twinax connectors are built to precise industry specifications. Pasternack BNC twinax connector items are available in jack or plug gender with 78 Ohm impedance. Connectors in twinaxial BNC are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These BNC Twinaxial connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this twinax BNC connector series is in-stock. In addition to being in stock, these twinaxial BNC connectors will ship the same day as they are purchased.
-
product
Powered NIM Crates
NIM "Nuclear Instrument Module" is the oldest and simplest nuclear electronics standard. Created in 1969 with AEC report TID20893 (Dec 1969), it defines a powered bin and plug in modules. NIM is the perfect standard for small and flexible setups for high resolution measurements with analogue electronics (amplifier, high resolution analog to digital converter, timing electronics as well as for low / high voltage supplies.
-
product
AC Clamp Meter
ST-2600
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions. ● Data hold function freezes the reading in dimly lit or hard to reach places. ● Low battery indication. ● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
product
USB-C® – USB 2.0 Receptacle HS SQ Test
AUT17037
This product is designed for USB-C USB2.0 Plug Host/Device Electrical Test.
-
product
Miniature Axial Extensometers
Model 3442
Jinan Testing Equipment IE Corporation
Weighing as little as 8 grams, these miniature extensometers are designed to have very low operating force with minimal specimen influence. All use an improved version of Epsilon’s dual flexure design which makes them very rugged for their size. With a module height of 15.2 mm (0.6 inches), they will fit in the limited space between grips that is typical with small test samples. Gauge lengths can be as short as 3 mm or as long as 50 mm. A newly designed gage setting pin and assembly allows the gauge length to be set accurately and repeatably to ASTM and ISO requirements for all gauge lengths. Reengineered quick attach wire forms provide simple and secure specimen attachment. Wire forms for round and flat specimens are included, as well as flat, 3-point, and vee knife edges. The wire forms may be removed to enable mounting using elastic bands or springs. A tethering attachment point provides fall protection and enables counterbalancing of the extensometer’s weight when testing delicate specimens.Model 3442 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller and Epsilon will equip the extensometer with a compatible connector wired to plug directly into the controller. For systems lacking the required electronics, Epsilon can provide a variety of solutions for signal conditioning and connection to data acquisition systems, chart recorders, or other equipment.
-
product
1.0/2.3 Connectors
Pasternack 1.0/2.3 connector category has many part numbers, most are RoHS and REACH compliant. 1.0/2.3 connector series in this category will terminate to coax or PCB (printed circuit board). Our 1.0-2.3 connectors are built to precise RF and microwave industry specifications. 1.0-2.3 connector series is manufactured in jack or plug gender with 50 Ohm impedance. 1.0-2.3 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 1.0 / 2.3 connector designs include crimp/solder, solder or solder/solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.0/2.3 connector series is in-stock. Not only are these 1.0-2.3 connectors in stock, but they ship the same day as they are purchased.
-
product
In-Line Spark Plug Tester
1807
Peaceful Thriving Enterprise Co Ltd
*Test for no spark condition.*With CE and RoHS Approval.*Handy pocket screw driver type.*Checks dead spark plugs in automotive.*Essential for trouble shooting all internal combustion engines.
-
product
EPON OLT ( Optical Line Termination )
OLT-1408
Hangzhou Huatai Optic Tech. Co., Ltd.
OLT-1408's Optical Line Terminal (OLT) adopts GiGA Ethernet Passive Optical Network (EPON) technology. It is a compact chassis with L2/L3 GiGA switching and routing function. All the functional components are modularized design and it supports hot-plugging with plugging and playing. 1~4 pieces of GiGA optical port or electrical port are optional in the uplink port, which provides a direct optical interface for the Ethernet/IP network core. 1~8 pieces of EPON optical port are optional in the down link port. Through a passive optical Network (PON), an optical Network unit link (ONU),it can provide final transmission with bandwidth up to 1Gbps for the user.
-
product
KIT for Test Cable Networks with Tools and Accessories
1RA370
Include: *Multi network cable tester for RJ45 (UTP / STP) and BNC*Modular crimping tool*LSA insertion tool*Cable stripper and cutter*30 units of RJ45 (8p8c) modular plugs*30 units of RJ11 (6p6c) modular plugs*24 units of colour strain relief*Comonents pocket*Zipper vinyl case
-
product
Network & Cable Testers
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
100 MHz Digital Output / Pattern Generator
TE8200
The TE8200 is a PXI based, high speed digital output/pattern generator product. The TE8200 is capable of 100 MHz high speed digital output and 512Kb memory depth per channel on its sixteen channels. It plugs into a single 3U PXI slot.
-
product
PXI Single 4x4 1-Pole 10A Power Matrix
40-551-003
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
RJ50 10-pin Modular Plug to DB-9 (Male), 1m
192190-01
RJ50 10-pin Modular Plug to DB-9 (Male), 1m
-
product
Tone Coax Cable Generator
240 HAL
The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
product
PCB Adapters - TriPaddle
TriPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.
-
product
Single and Combined Sensors
REINHARDT System- und Messelectronic GmbH
The robust climate sensors are used worldwide and offer longtime stability, high measuring accuracy and easy commissioning by plug and play
-
product
PXI 8x4 1-Pole 10A Matrix With Loop-Thru
40-551-101
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, this module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. This version of the 40-551 may be expanded to larger matrix sizes using cabling to daisy-chain the X and Y signals Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
