Plugs
A male connector.
-
product
Osprey PCI Qbus Adapter
9668
Dual-height card plugs into PDP-11 Qbus backplane. Fibrechannel cable plugs into Qbus logic connector on Osprey /TXP. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
product
Cable Assembly, Receiver, TriPaddle, 20", (for NI PXI-2527) with Banana Plugs for a DMM
541122953
Cable Assembly, Receiver, TriPaddle, 20", for NI PXI-2527 with Banana Plugs for a DMM
-
product
Direct BNC
0001045
Interface board plugs directly into National Instruments 68 pin multifunction and simultaneous sampling DAQ cards (PCI and PXI). First four analog inputs, two analog outputs, and trigger channels are available on BNC connectors (SMA/SMB optional).
-
-
product
PXI/PXIe Power Relay Module, 24xSPDT, 5 Amp, 50-Pin SGMC Connectors, With Interlock
42-158-002-HI
The 40/42-158-002-HI is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 68 Pin VHDCI Plug
510109473
PCB adapter from a 192 position QuadraPaddle receiver module to one 68 pin VHDCI plug
-
product
Mass Interconnect
Mass interconnect is a way of connecting test instrumentation to a device under test (DUT). To put it simply, mass interconnect is a very large plug and socket which connects your device under test to your test instrumentation without the mess and hassle of having to connect each signal separately.
-
product
Rackmount Kit For Infiniium EXR-Series, 8U
EXR2RACK
The EXR2RACK rack mount kit includes all parts needed to mount your Infiniium EXR-Series oscilloscope in an 8U open frame rack and includes a Support tray, Trim plates, BNC connectors to be inserted into the bottom trim plate, black rubber stoppers to plug holes in bottom trim plate if the hole is not being used for a BNC connection, Two track rails, Two clamp brackets, both right and left Top clamp brackets, screws, and nuts.
-
product
Load Cell Indicator
9840
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
product
Test Leads
AL-34WB
Standard Electric Works Co., Ltd
● Wire length: 1.2m approx. Silicone insulated wire (1000mm) with wire connected to straight input plugs (130mm PVC wire), and wire for clamp (100mm PVC wire). ● Outside diameter of silicone insulated wire: 5mm Outside diameter of PVC wire: 3.5mm● Input plug color: Red•Green•Black•Blue ● Current rating: 5A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
product
Peak Track Instrument
90323
The model 90323 Peak Track Instrument is a general-purpose sensor readout device designed to complement our AutoID line of load cells and torque sensors. AutoID is a term that indicates that the calibration information for a sensor is stored on a chip inside the sensor’s connector. AutoID allows true “plug and play” operation without manual calibration procedures of any kind. The unit is also equipped with a 2-line alpha-numeric display and single button operation for simplicity.
-
product
Signal Generator, Audio, Compact, Handheld, 1 Channel, 20kHz, FM, US Plug
72-490
Highly versatile compact audio generator is perfect for sound system and speaker component testing. Its high precision and remote VCO input make it suitable for the serious test environment, yet its compact size and low cost make it suitable for any tool box. This device is designed to be connected to the line level of any consumer or commercial designed audio amplifier. While it is designed to be used with unbalanced inputs, it is also suitable for balanced equipment
-
product
FTP Patch Cable, 5″ C6, 4/Clam
#610025C
Platinum Tools’ premium 5″ Cat6 FTP Patch Cables are made with testing networks in mind. Plug in and out all day long and know you will have consistent and precise connectivity every time. Designed for repititive, long cycle life! 849160007951
-
product
LXI Reed Relay Matrix - Dual 64x8 Plugin, No Direct Y Access, 6 Analog Buses
65-223-101
These Modular LXI Matrix Reed Relay Matrix Modules plug into our LXI Modular Chassis (model 65-200-002)—providing access to all signal connection on 200 pin connectors. They are constructed using Pickering Electronics' Reed Relays offering maximum performance and reliability as well as very fast operate times.
-
product
Universal CMM Software Module
Verisurf CMM
Plug and play CMM communication for Hexagon Dea, Leitz, Mitutoyo, Wenzel, Pantec, Nikon, LK or Zeiss™️ machine controllers, as well as Renishaw, Tesa, Hexagon Leitz or Zeiss™️ head controllers.Optional support for scanning probes and error mapping compensation for geometric, volumetric, orientation, positioning and kinematic errors in the CMM structure that affects accuracy.
-
product
Coil-on-Plug Spark Tester
MDCOPT
The Coil-on-Plug Spark Tester provides an easy way to check ignition systems with coil-on plugs (COP). Quickest way to test for no-start conditions. Inductive test cannot be performed because there are no plug wires. Applications include Ford, Chrysler, Mitsubishi, Nissan and many more.
-
product
Cable Assembly, Receiver, High Frequency, 36", 10 SMA Plugs
540153010212
Cable Assembly, Receiver, High Frequency, 36", 10 SMA Plugs
-
product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
Fuse Buddy
Designed specifically for circuit testing, Fuse Buddy plugs right into fuse socket - easy connection for circuit current testing.
-
product
3U CPCI To PCI 4 Slot Adapter
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
product
Powered VME Crates
6U VME 475 Mini
The VME475 mini crate series offers hot-swappable, redundant power supplies in a 7 slot, compact but modular designed VME chassis. A front-side-plug high performance DC fan is used for cooling with front to rear and side to side air flow.
-
product
SparkFun MicroMod Teensy Processor
The SparkFun MicroMod Teensy Processor leverages the awesome computing power of the NXP iMXRT1062 chip and pairs it with the M.2 MicroMod connector to allow you to plug it into your choice of compatible MicroMod Carrier Board. With the M.2 MicroMod connector, connecting your Teensy Processor is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards). Adding a Teensy to your desired project has never been easier!
-
product
Cable Assembly, Receiver, TriPaddle, 36", for NI PXI-2527 (uses NI TB-2627) with Banana Plugs for a DMM
541123200
Cable Assembly, Receiver, TriPaddle, 36", for NI PXI-2527 (uses NI TB-2627) with Banana Plugs for a DMM
-
product
Cable Assembly, Receiver, Mini Power/TriPaddle, 36", 7-Pin DIN and 4 Banana Plugs
540078010211
Cable Assembly, Receiver, Mini Power/TriPaddle, 36", 7-Pin DIN and 4 Banana Plugs.
-
product
VPX55-3HU 3U VPX Power Line Conditioner with Holdu
VPX55-3HU
The VPX55-3HU is a 400-Watt DC/DC Power Line Conditioner which plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" or 1.0" power slot. This off-the-shelf solution is compatible with VPX specifications and addresses the need for 3U VPX power applications requiring an optional VITA 62 Energy Storage Module.
-
product
Tone Test Set
240 Weathertite
The AINES Model 240 Tone Test Set is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
product
Mission Critical, Fault Tolerant Power Supplies
Series HSF
- Hot-swappable plug-in power supplies.- Designed to be combined in an N+1 fault-tolerant power system.- Front panel voltage adjustment trimmer for adjustment of output voltage.- Built-in forced current sharing and or-ing diodes.- May also be used independently as a multi-output power supply.- Designed to be sustainable - new models are backward compatible with existing racks.- Available in 1U and 3U sizes. Mounts in 19-, 23-, and 24-inch equipment racks.- All models include power factor correction (PFC).- Full service customized DC power distribution systems can match power supply output(s) with your load(s).- I/O connections via 24 pin connector that plugs into rack adapter. External connections are made via rack adapter.- Surface mount technology permits minimum mounting space.- Entire RA 19 racks populated with HSF power supplies can be connected in parallel, parallel-redundant or series.- HSF are CE Marked per per the LVD, EMC and RoHS 2 Directives. See applicable Declaration of Conformity.- Compliant with UL 8750, Standard for LED Equipment,- Watch video of NEBS GR-63-CORE earthquake and office vibration testing.
-
product
6 Position Plug Socket Switch Life Tester
CZKS-6
It is designed according to terms and conditions of IEC60884-1, IEC60669-1, GB2099.1-2008 and GB16915.1-2003, for life test of plug and socket and switch products of household and similar use appliances. The device can connect with matched load cabinet, in order to conduct a test of electrical life, normal operation and breaking capacity. The equipment provide some clamp, it can test plug and socket production, wall switch, rocker switch, dial plate switch and button switch.
-
product
High-Speed Digital Analyzer
HDA125
Plug in a high performance logic analyzer to your oscilloscope for enhanced visibility during mixed signal analysis. The HDA125 High-Speed Digital Analyzer supplies 12.5 GS/s sample rate and up to 18 leads in a small modular form factor.
-
product
Multi-Modular Cable Tester
3PK-NT005N
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
