Plugs
A male connector.
-
product
Testing Leads Assortment (16PCS)
3605B
Peaceful Thriving Enterprise Co Ltd
1. Suitable for use on the 6-24V circuits2. 4mm banana plugs connection3. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
product
AC Clamp Meter
ST-2600
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions. ● Data hold function freezes the reading in dimly lit or hard to reach places. ● Low battery indication. ● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Power Tester
PS-228
The product designs with LCD to show ATX power voltage. Easy to plug with ATX power 20/24 pin and plug in (P4/P6/P8) to show the voltage on the LCD panel.
-
product
Amplifier Systems Band Specific
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
product
Universal Plug-In Power Supplies
PeakTech Prüf- und Messtechnik GmbH
AC/DC-Adaptor in latest eco-friendly-technology. Combined with the wide range of line voltage from 100 - 240 V AC max. output current of 1500 mA and an output voltage of 3 - 12 V DC. With the included plug set of 6 pcs the adapter can be used universal. This powerful adapter is short-circuit proofed, has an automatic thermal fuse and is equipped with an overload protection.
-
product
10RJ50-DB9M Serial Cable, 10Pos Modular Plug to DB-9, 2 m (non isolated)
182845-02
S8 Serial Cable, 10Pos Modular Plug to DB-9, 2 m (non isolated)
-
product
Frontend - Frequency Extension to D-Band (110 GHz to 175 GHz)
FE170ST
The R&S®FE170ST is ideal for early subterahertz and 6G research. By extending the frequency ranges for the R&S®SMW200A and R&S®SMM100A to the D band (110 GHz to 175 GHz) engineers can access the range they need and develop the next generation of mobile communications. The easy-to-use, fully-calibrated solution is compatible with our signal generator, analyzer and oscilloscope environments. Plug it in and start designing the next generation of mobile communications today.
-
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Eurorack Module Tester
TST
Test your modules safely without reaching into your case! The TST has two keyed 16-pin headers on the front of the module so you can plug and unplug quickly and easily. Two 16-pin plugs are included to shield the power pins when the module is not in use. It also has LEDs to indicate the power status on each rail.
-
product
VARCOM® Capacitor Controls
*Industry leader in capacitor controls for rural electric, public power and investor owned*Targeted to the special needs of the utility operator*VarCom Controls are simple to use, yet provide sophisticated system auditing*Plug and play–VarCom Controls work with a variety of cap bank switch, sensor, SCADA/DMS software and communication devices*Best customer service and technical support in the market–before, during and after the sale*Minimal training requirements–Controls can be programmed directly from the front panel or by using the non-licensed*VarWare® Software available from our website*10-year warranty
-
product
SAS
SCHILLER AUTOMATION GmbH & Co. KG
The Gen4 Mini-SAS HD adapter kit will facilitate compliance testing for SAS-4 host, device, and cable. The left and right-hand version plug adapters are designed to test side-by-side.
-
product
Fusion Bonded Cable Jumpers
Series 152FB
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
-
product
32-Ch High Voltage Relays & Multimeter
YAV90HVT
The YAV90HVT is used as an automatic CAN bus controlled floating AC/DC true RMS digital volts/milliamps meter with built-in scanner, able to work directly in appliances and industrial mains powered electric/electronic equipment.Its powerful microcontroller allows to work as a distributed device able to data acquire, compare and return high level messages, reducing test operation time.The analog output is used as a set value for the optional high voltage programmable power supply for Hipot tests up to 1500V.The board uses Tripaddle connection modules and can operate as stand alone or be mounted on a standard Virginia Panel receiver.The board includes National Instruments LabView virtual control panel and operating software for a true Plug & Play operation.
-
product
EDFA
SPA-2-4X22-WDM EYDFA
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
product
Cable Assy 78-Pin D-Type Female to 16 x Mini Thermocouple Plugs, 1m
A078DFR-16M002T5A100
This 78-pin D-type thermocouple cable assembly is terminated with 16 male mini thermocouple plugs. It is constructed from 7/0.15 (26AWG) silver plated copper wire and screwlocks are provided to secure the D-type to its associated products.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Professional LAN Cable Tester w. 4 Remote Loopback Plugs
LANTESTPRO
The StarTech.com Advanced RJ45 LAN Cable tester allows a single person to test several long cables faster and more efficiently than ever before. The tester uses remote loop-back plugs that each have their own unique ID number that the tester can identify.
-
product
SparkFun Breadboard Power Supply 5V/3.3V
Here is a very simple breadboard power supply kit that takes power from a DC wall wart and outputs a selectable 5V or 3.3V regulated voltage. The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled VCC and GND plug directly into the power lines. The lone pair of pins have no electrical connection but help support the PCB.
-
product
USB Modular Digital Multimeter, 5 digit
U2741A
The Keysight U2741A USB Modular Digital Multimeter provides a broad range of measurement functions, including temperature and frequency. The U2741A is a 5.5-digit resolution digital multimeter that is able to capture up to 100 readings/sec. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
product
50Ω UWave SMA Cable Assembly, 26.5GHz, 0.1m
40-977-542-0.1m
50 Ohm uWave SMA Plug to uWave SMA Plug Cable Assy, 26.5GHz, 0.1m Long.
-
product
50Ω UWave SMA Cable Assembly, 26.5GHz, 0.25m
40-977-542-0.25m
50 Ohm uWave SMA Plug to uWave SMA Plug Cable Assy, 26.5GHz, 0.25m Long.
-
product
Combo Test Lead Kit
U8201A
Designed for use with U3606A DMM | DC power supply; includes leads, probes, alligator clips, SMT grabbers, and banana plugs
-
product
Shield
Arduino Motor Shield Rev3
The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.
-
product
HDMI Assembled Test Connector
HDMI Testplug with plug (1000 mm cable), HDMI Testplug with female socket (1000 mm cable), HDMI Testplug with 19-pin connection board. Applications in video and audio systems.
-
product
Breakout Boards
D Series Boards
D Series Breakout Boards are open designs that provide signal access when troubleshooting. Signal connections are accomplished by inserting or removing Mini-Jumper plugs. All normal and high density D type connectors are available. Current carry capability is from 2.25A to 5.3A. Normal Density D Type: 9, 15, 25, 37 and 50 positionsHigh Density D Type: 15, 26, 44, 62, 78 and 104 positions
-
product
Manual Test Station
We also develop manual test stations for you, which save costs for small series or are required for multi-adaptive test objects. This refers to test objects that are usually not contacted via a needle bed, but rather via plug connections.
-
product
OBDLink Bluetooth Scan Tool
4251BT
OBDLink Bluetooth features a Class 1 Bluetooth transmitter for maximum range, and Plug and Play connectivity with popular Bluetooth devices including Android and Symbian based phones. The built-in USB port makes this the most versatile scan tool ever offered!
-
product
Audio Test Tone Generator
Tone Plug
The TONE PLUG offers five user selectable sine wave test tones at frequencies of 100, 250, 400, 1K and 10KHz. An additional 5 special function test signals are also provided.
-
product
6 Pin Round Pin Tester / Maintenance Kit
#8027
Innovative Products of America
Test, clean and restore 6 round pin trailer connections. Included tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 6 round connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsPatentedKit Includes: #7897: 6 Pin Round Pin Tester, #8022: 6 Round Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
