Plugs
A male connector.
-
product
Load Cell Transmitter
MODEL SST-LV
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
Save A Watt HD
P4472
Take control of your electronics and appliances. Simply connect them to the Save A Watt® HD timer, and they will turn on and off based on your preferred settings. Electronics which are plugged into an outlet are drawing power even when not in use, slowly draining your wallet! Having the power to program ON/OFF times saves you money, and prolongs the life of your electronics. With a large, backlit, digital face, setting the time couldn’t be easier or more intuitive. If you forget which settings you chose, it only takes a glance to find out.
-
product
180V-260V AC Socket Tester With RCD Test (For UK)
1943
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 180~260VAC circuit.*LED indicators & Digital display.*30mA leakage current measurement.*RCD Test.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 11W*Frequency: 50Hz
-
product
34945EXT Distribution Board, For One 87204x/206x Or 87606B Switch And Two N181x Switches
Y1152A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
Capacitive Discharge Testers
For IEC Testing of residual voltage after plug disconnect. The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results. Scope output for viewing decay waveform. Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335. Recommendations for Pluggable Type B equipment. NIST calibration supplied; A2LA calibration available. 16A option for testing large equipment.
-
product
Socket Accessories (SMT Options)
The SMT adapter consists of standard high temperature FR4 with plugged via technology, eutectic SN63PB37 solder balls or SAC lead free solder balls and threaded inserts for mounting the socket. The top side of adapter has SMT pads to receive socket interconnect and the bottom side has appropriate solder balls for corresponding pitch. This FR4 adapter with balls can be soldered to the SMT pads in the target board. Then socket can be mounted to the threaded insert on the FR4 adapter.
-
product
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs
510140111
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs.
-
product
I/O Modules
*Configurable input / output functions*Direct connection of hydraulic valves or joysticks*Modules with M12 connector or central plug*High-performance CAN interface for various communication tasks*E1 type approval (German Federal Motor Transport Authority)
-
product
Cble Assmbly Ins Push-On F To RJ45 Plug
#TCA001
Cable Assembly, Insulated Push-on F to RJ45 Plug, 849160004783
-
product
HeNe Laser System with Built in Receiver and Power Supply
5519B
The Keysight 5519B Laser is a Helium Neon Laser (HeNe) that offers exceptional stability. The laser is a complete system with a built-in receiver and its own power supply that plugs directly into an AC power outlet.
-
product
Cable Assembly, Receiver, TriPaddle, 20", 4 x RJ50 Plugs
540043010101
Cable Assembly, Receiver, TriPaddle, 20", 4 x RJ50 Plugs
-
product
Temperature Input Device
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Clamp-On / Precision / Split Core Current Transformer
Transformer Ratio (Arms) : 100A / 1AColours : Red, yellow, blueConnection : Safety Sockets for Banana Plugs ф 4mm Jaw Opening : Cable Dia 15mm max.
-
product
Internal DAQ Cards
PCIe, PCI, PC/104, CAN
PC data acquisition cards are particularly suitable for stationary measurement applications. Outstanding in this category are the PCI(e) multi-function cards PCI-BASEII and PCIe-BASE on which you can plug different measurement and control modules to optimize the price-performance ratio.
-
product
Extended Test Lead Kit
U1161A
The Keysight U1161A extended test lead kits are compatible with the U1230, U1240, U1250, and U1270 Series handheld digital multimeters. The set includes two extension test leads (one red and one black), two test probes, medium-sized alligator clips, and 4 mm banana plugs.
-
product
3 Position Plug Socket Switch Life Tester
CZKS-3
It is designed according to terms and conditions of IEC60884-1, IEC60669-1, GB2099.1-2008 and GB16915.1-2003, for life test of plug and socket and switch products of household and similar use appliances.The device can connect with matched load cabinet, in order to conduct a test of electrical life, normal operation and breaking capacity. The equipment provides some clamps. It can test plug and socket production, wall switch, rocker switch, dial plate switch and button switch.
-
product
Mini Fiber Optic, Patchcord, ITA, 36", Polymer Optic Fiber, to SMA Plug
7-413845516-036
Mini Fiber Optic, Patchcord, ITA, 36", Polymer Optic Fiber, to SMA Plug.
-
product
3U 6-slots 25Gb Backplane Aligned To SOSA, Apertures For VITA 66/67 Modules
1SVX306AxP-xxxx
Designed in alignment SOSA, this 3U backplane offers 6 PIC (Plug in Card) slots supporting high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
product
6-way Round Pin Vehicle side Circuit Tester
7897
Innovative Products of America
The 6-way Round Pin Trailer Circuit Tester tests trailer circuits on older light to medium duty trucks and RVs. Plug the 6 pole trailer tester into the back of the vehicle and apply the Brake Lights, Turn Signals, Running Lights etc.
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
PCB Test Points
Test Socket 2mm. Plug 2mm. Measuring Socket 2mm . 2 Pin Test Socket 2mm. Miniature Test Socket 2mm
-
product
Single 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-013
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexers. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
Universal ZIF (Zero-Insertion-Force) DIP Test Socket
Series X55X
Universal Zero Insertion Force DIP Test Socket. All pin count sockets go into PCB with either .300 or .600 [7.62 to 15.24] centers. Sockets can be soldered into PCBs or plugged into any socket. Socket fits into Aries or any competitive test socket receptacle.
-
product
PCI Evaluation Board
BCM91125E
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
product
Inertial Measurement Units
IMU
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
product
Cable Assembly, Receiver, 20", Micro Power & Micro Coax, 17 MCX Plugs
540338010147
Cable Assembly, Receiver, 20", Micro Power & Micro Coax, 17 MCX Plugs
-
product
Cable Assembly, Receiver, Micro Coax, 36", 10 SMB Plugs
540092010247
Cable Assembly, Receiver, Micro Coax, 36", 10 SMB Plugs.
-
product
Glow Plug Tester
The analyser test the condition of the glow plug in diesel engines and it comes with a graphical display without any language it shows the actual resistance of the glow plugs with conclusive result after the test. The analyser will switch off automatically if the tool is not being used, to conserve battery life. The tester comes with a built-in torch light to light-up dim surroundings for finding the glow plug or other car electrical problem.
-
product
Plug and Switch Testing
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right.
-
product
Cable Assembly, Receiver, 20", VTAC, 2 RJ45 Plugs
540224010167
Cable Assembly, Receiver, 20", VTAC, 2 RJ45 Plugs.
