Test Adapters
See Also: Interface Test Adapters
-
Product
ABex Rear Module for Utility Power Supply
ABex RM-UTILITY
-
The ABex RM -Utility is a rear module for the ABex-System. It provides 5 galvanically isolated fixed supply voltages for TUA (Test Unit Adapter) and cabinet supply. It features an over current protection and a software-controlled power enable.
-
Product
Test Fixture Adapters for In-Circuit Test Fixtures
-
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
Product
Test Adapter / Pneumatic Adapter
-
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
-
-
Product
PCI bus Test Adapter
pcibus1b
-
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
-
Product
Chip Test Adapter
SOJ EDO/FPM
-
Our new addition to the RAMCHECK line provides support for common 20 to 42-pin EDO/FPM DRAM SOJ chips of sizes 256Kx16/18, 1Mx16/18, 8Mx8, 16Mx4, 2Mx8, 4Mx4, 16Mx1, 1Mx4, and 4Mx1.
-
Product
Test Adapter
FECVF1600
-
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
Product
DDR4 Pro Memory Test Adapter
-
This memory test adapter for the RAMCHECK LX includes an extraordinarily rugged test socket for many thousands of insertion/removal cycles.
-
Product
Digital and Analog Test Sets
-
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
Product
Automatic Test Equipment, Test Interface Units and Test Program Sets
-
Axis Aerospace & Technologies Ltd.
AXISCADES is a pioneer in Test Solutions and has a long pedigree in developing Test Systems. AXISCADES has designed and developed Automatic Test Equipment, Test Interface Units/Interface Test Adapters and associated Test Program Set Software for Indian and Global, Aerospace and Defence OEMs and End Users.
-
Product
EBIRST 78-pin D-type To 68-pin Female SCSI Adapter
93-006-222
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Interface Test Adapter
ITA
-
Circuit Check is focused on the military and aerospace market. Our solutions are delivered according to a rigorous set of test requirements and quality metrics. The Circuit Check staff of engineers follow a defined Project Management process to control the project deliverables,manage the scope, and meet the quality needs for in-field serviceability and test system longevity.
-
Product
EBIRST 50-pin D-type To 37-pin D-type Adapter
93-005-418
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Manual Test Adapter With Rigid Needles
-
Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
-
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
EBIRST 50-pin D-type To 2x8-pin Power D-type Adapter
93-005-236
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
-
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
Product
EBIRST 200-pin LFH To 160-pin DIN Adapter
93-002-410
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
NI HIL and Real-Time Test Software Suite
-
Suites combine LabVIEW Professional Development System with NI's most popular application softwareIncludes LabVIEW Professional, VeriStand, and the LabVIEW Real-Time and LabVIEW FPGA modulesEach new suite includes a one-year NI Training and Certification membershipSoftware is shipped on USB 3.0 media with NI device drivers included to speed up your installationConfigure real-time test applications quickly and easily; add custom functionality
-
Product
NI Automated Test Software Suite
-
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
Product
Wireless Test Standards Software
-
Generate and analyze signals for cellular and connectivity standards with NI PXI RF instrumentationPerform advanced automated test with the easy-to-use NI-RFmx software APISave on all NI RF wireless test software under a single license
-
Product
Row Expansion Cables
Y1134A
-
Easily configure an expanded matrix using this expansion cable with the 34934C and 34934T terminal blocks
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 36" Cables
510150143
-
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 36" Cables
-
Product
Cable Free ATE
CABLEFREEATE
-
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
Product
EBIRST 200-pin LFH To 104-pin D-type Adapter
93-002-422
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Adapter, 2.4 mm (m) to APC-7, DC to 18 GHz
11902A
-
The Keysight 11902A is a 2.4 mm male to APC-7, metrology grade adapter with dc to 18 GHz operation.
-
Product
TestStand
-
TestStand is industry-standard test management software that helps test and validation engineers build and deploy automated test systems faster. TestStand includes a ready-to-run test sequence engine that supports multiple test code languages, flexible result reporting, and parallel/multithreaded test.
-
Product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 6 Slot, to (1) Cat6
510171105
-
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat 6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules. Please note this part is too wide for use in multiple adjacent slots.
-
Product
Adapter Plate, 9050 Enclosure to 9025 ITA
410112976
-
Adapter Plate, 9050 Enclosure to 9025 ITA (ITA Positioned on Lower Part of Enclosure)
