Indicators
give sign to the state of something.
See Also: Angle Position Indicators, Fault Indicators, Loop Indicators, Voltage Indicators, Annunciators
-
Product
FTTH ONT CHECKER
FOC-100
-
•Easy to check ONT in use at FTTH Drop Terminal Side•Easy to check the ONT connection status•Check unused port Detection•Optical Fiber Identier•Indicator for signal presence or absence (live or dark ber)•Optical power measurement•Very low cost and compact type
-
Product
Dimensional Calibration
-
Process Instruments certifies Gage Blocks with a state-of-the-art Pratt & Whitney Gage Block Comparator. Outside and Inside Micrometers, Depth Micrometers, Height Gages, Calipers and Dial Indicators can be repaired and calibrated to manufacturers'' specs.
-
Product
Acute High Voltage Differential Probe, 50x/500x, 25MHz, 3500V
ADP5025
-
*USB Powered (or Power Bank)*Bandwidth up to 25 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
Product
50-Pin DIN-Rail Wiring Board W/ LED Indicators
ADAM-3951
-
Low-cost DIN-rail mounting wiring terminal module for PCI-1752/1754/1756 with 50-pin SCSI female connectorScrew-clamp terminal blocks allow easy and reliable connectionsEach LED indicates its current bi-directional I/O logic status with either green or red lightCase dimensions (W x L x H): 77.5 x 179.5 x 41.5 mm (3.1" x 7.1" x 1.6")To Be Used With PCI-1752U, PCI-1754, PCI-1756
-
Product
Acute High Voltage Differential Probe, 20x/200x, 100MHz, 1400V
ADP2100
-
*USB Powered (or Power Bank)*Bandwidth up to 100 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
Product
Indicating Instruments
-
In continuous level measurement, the filling height in a vessel is repeatedly detected. The measured value is further processed, e.g. as a 4 … 20 mA signal in a PLC or process control system. Indication of the measured value directly on site is also frequently requested.
-
Product
LED Inspection
-
Indicates which LEDs are not working. Checks if all diodes are placed in the correct places. Independently configures a test program for each new LED panel. Fast and effective – 1000 LED panel test takes up to 3 seconds.
-
Product
Bidirectional Weight Indicator
480
-
Large 0.8 in LED 6-digit Display• 100,000 displayed graduations• 523,000 internal counts• Powers up to 10 Load Cells• Tension/Compression operation• NEMA 4X stainless steel enclosure• Measurement Rate up to 40Hz• Selectable filter settings• 0.1uV/graduation signal sensitivity
-
Product
MT Inspection Scope
Um
-
● Test 12 or 24 fiber MT Connectors● Find Endface defects fast● 800x Magnification●Numbered Dial Indicator to quickly identify which fiber you're onThe Um MT Inspection Scope accurately shows defects in your MT 12 or 24 fiber connectors. Quickly view each fiber to save time and money. Our unique Fiber Dial shows which fiber you are inspecting. No more getting lost!The Um MT is compatible with our Eagle Inspect Software. Create reports with images for your MT connectors.
-
Product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
-
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
Product
Sound Level Datalogger
DSL 331
-
Auto Ranging Measurement 30dB to 130dB. Work with Window Software. 32,000 Records Data Logger. Bar graph Indication with Back Light. RS-232 Real Time Display Software for Window 95/98/2000
-
Product
Vol-Con® Solenoid Voltage Tester
61-076
-
*Extremely rugged and reliable*Vibrates when AC voltage is present*Indicates AC/DC voltage level*Replaceable leads with shielded probe tips (IEC61010-031 compliant)*Bright, long-life LED™s and neon indicator lamp*Dual voltage indication for backup safety*2-year warranty
-
Product
Switch Indication Maintainer Plus
The SIM-Plus
-
The SIM-Plus - Switch Indication Maintainer Plus is a handheld device used to simulate normal switch correspondence while performing periodic maintenance or testing. The SIM-Plus also provides the ability to power the switch machine using local switch battery or, if battery is not available, provide a temporary source of power from an optional power pack.
-
Product
Digital Indicator for Strain Gauge Sensors
AD-4530
-
Low cost digital indicator for various applications. Suitable for measurement of load, pressure, torque, tension and more at an affordable price.Digital Zero (DZ) stores zero data at any measurement point. This function can also be used to tare weight. Measurement can simply be restarted when it was interrupted by a loss of power.Power on zero function adjusts to zero when the power is turned on.Digital filter provides stable measurement results.Digital span calibration. Easy calibration just by inputting the rated output of a sensor. No need to use a mass.
-
Product
Strain Gauge Measuring Instruments
-
It is a Strain Gage Indicator and also function as a Strain Gage Transducer Indicator.As a Strain Gage Indicator, it can support 10 types of bridges and dummies. While if used as a Strain Gage Transducer Indicator, there are 24 bits A/D converts to make the measurement.
-
Product
Portable Hand Held Load Cell Indicator
MODEL SSI
-
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a Units key for automatic conversion of readings for load, torque and pressure. The SSI has an ultra-fast signal-sampling rate of 15,360 samples/second for true peak and/or valley testing capability. Auto-tare allows the meter to be set to zero for any input signal level. The SSI also features a USB port for data logging to a PC. You can also log data to the SSI’s internal memory storing up to 16,000 time and date stamped readings. The SSI also features 2 built-in solid-state alarm relays with LED and audible indicators. The SSI will operate up to 65 hours on a single charge or use the included battery charger for applications where the SSI is mounted permanently.
-
Product
3 ¾ DIGIT 2000A AC / DC Digital Clampmeter
KM 2775
-
Kusam Electrical Industries Limited
• Auto Ranging• Full Automatic measurement• Range change function• Data Hold function freezes the reading• Continuity & Diode Measurements• Auto Power Off• Low Battery Indication
-
Product
Speed Indication & Sensing
-
Provide an accurate speed display at an economical cost. Available with Digital or Analog displays in both a panel and base-mount enclosure. Each maintains the reliability and rugged performance customers expect.
-
Product
Super-Safeway Three Wire Circuit Tester
1301270009
-
Super-Safeway Three Wire Circuit Tester, 3 Indicating Lights & Receptacle Tension Tester in Carrying Case
-
Product
Mini AC Leakage Current Clamp Indicator
MLD-18
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・The LED will blink when detection leakage current exceeds AC 15mA.・Supports ELB with high-speed detection of 20ms.・The operating period is about one month, which is suitable for detecting intermittent leakage current.
-
Product
600A Digital Clamp Meter
7128B
-
Peaceful Thriving Enterprise Co Ltd
This is a auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity and non contact voltage sensing. Sub switch included Function Select, Max-Min Indication, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Illumination and Back-light.
-
Product
Infrared Thermometer
6571
-
Peaceful Thriving Enterprise Co Ltd
*Low Battery indicator.*Distance to spot ratio is 10:1.*Laser Indicator and Background-light.*Changeable between ℃ and ℉.*Emissivity Range: 0.85/0.90/0.95.*Temperature range: -20-500℃ (-4-932°F).
-
Product
Loop Powered Indicators
-
DEVAR loop powered indicators are designed to easily convert any standard 4 to 20mA loop signal to readout directly in engineering units. Optional back-lit display available.
-
Product
Alcohol Tester
-
Shenzhen Graigar Technology Co.,Ltd.
Electrochemical (fuel cell) alcohol sensor, Module changeable Test Range: 0.000-2.000mg/l (0.400%B.A.C; 4.000%oB.A.C; 4.000g/l;) Alarming level: Pass level: 0.090mg/L (could be modified) Fail level:0.250mg/L (could be modified) Accuracy: +/-10% Work temperature: -10oC-50oC Work humidity: <95%RH (No Dews) Battery: 2XAA NiMH batteries, rating capacity: 2.1AH Dimension lXbXh: (mm) 250X105X400 Indication manner: mg/l,mg/100ml,g/l ,%BAC,%oBAC optional Coin for single time: 0-15 (For 0, the tester can be tested without coin). Coin diameter: 20mm-28mm Coin thickness: 1.2mm-2.5mm Coins Capacity: about 200 pieces Straw capacity: 200pcs(⊄<=7mm) Breath sampling time: about 5 seconds continuous breath.
-
Product
Digital ELCB (RCD) Tester
2820 EL
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Operating voltage 100-450V L-E.● Rated current 999mA, at 317V AC/50Hz.● Checks ELCB trip time and trip point (sensitivity).● Auto off and auto ranging.● Phase angle selection(0° / 180°).● Indicates tripping phase angle.● Impact resistant enclosure.● Over temperature shut-down.● Transient protection.● Suitable for heavy industrial use.● Fused.
-
Product
RPM Indicator
CS2-RL
-
CS2-RL RPM Indicator has been designed with high accuracy measurement, display and communication of pulse (Frequency).The innovation feature is auto-range input from 0.01Hz~ 100KHz (option ~140KHz) and the display resolution will auto-change to show the highest according to input frequency.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of testing and machinery control applications.
-
Product
Phase Sequence Indicators (Contact Type)
4156 PR
-
Standard Electric Works Co., Ltd
● The 4156 PR is used to identify the leads of a diconnected motor so that when the motor is in true phase sequence, it will run in the desired direction.
-
-
Product
Digital Tap Position Indicator
-
NMC''s latest offering, Digital Tap Position Indicator with 4-20 mA, type TX-205, is a Micro controller based instrument used to indicate the Tap Position of the OLTC along with it transmits 4-20 mA Analog Single/Dual Output. It is a field adjustable instrument. Size : 96*96*85 mm. Aux. Supply : 85 V-265 V AC-DC.
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
