TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
Low Noise Amplifier
-
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
40mA Multi-Channel Amplifier
-
For the precise nanometer movement of actuators and other piezo products, an amplifier is required. Multi-channel amplifiers allow you to control multiple actuators or piezo products with a single amplifier. The NV40/3 piezo amplifier was designed for controlling low voltage piezo elements. It includes a voltage amplifier, a display and a PC-interface. The high-resolution display shows the voltage of the actuator, along with the mode of operation and the temperature inside the amplifier.
-
Product
Waveform Amplifier 30 Volts Pk-pk
WA301
-
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.
-
Product
Amplifier
AC-100
-
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
Product
Solid State Power Amplifiers
SSPAs
-
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
Waveform Amplifiers
-
Most waveform generators are limited to 20V pk-pk EMF output level. The WA301 waveform amplifier can be used to increase that level up to 30V pk-pk.
-
Product
Isolation Amplifier Analog Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Audio Amplifiers
-
An electronic device that increases the strength (amplitude) of audio signals that pass through it.
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
Low Noise Amplifiers
-
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
Product
Programmable Gain Amplifiers
-
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
Product
Microwave Amplifiers
MShU Series
-
*Ultrawide Operating Frequency Range*Small Size*Low Noise Figure*Low Power Consumption
-
Product
Pulsed ESR/EPR: Pulsed Injection-locked IMPATT Amplifiers
-
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
VCOM Amplifiers And Calibrators
-
Renesas offers various VCOM amplifiers including rail-to-rail input-output operational amplifiers and rail-to-rail input-output buffers, as well as programmable VCOM calibrators that are ideal for display applications.
-
Product
Power Amplifier
MS 2011
-
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
Modal Exciters & Amplifiers
-
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Product
High Speed High Voltage Amplifier
WMA-300A/360
-
The WMA-300A/360 model is a -180V to +180V (360Vpp) high speed, high voltage amplifier designed for driving capacitive loads, such as piezo actuators, capacitive MEMS and EO-modulators.
-
Product
Broadband Amplifiers
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue offers a variety of RF amplifiers for broadband CATV or OTA (over-the-air) applications. Be it a 1GHz power doubling two-way indoor distribution amplifier or a mast-mounted preamplifier, or anything in between, we have you covered.
-
Product
Charge Amplifiers & Signal Conditioning
-
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
Product
Driver Amplifiers
-
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
