-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
75 Ohm SMB Connectors
-
Pasternack 75 Ohm SMB connector category includes dozens of part numbers, most are RoHS and REACH compliant. 75 Ohm SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB 75 Ohm connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm SMB connector products are built in jack or plug gender with 75 Ohm impedance. SMB connectors in 75 Ohm impedance are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm SMB connector series is in-stock. Not only are these connectors with 75 Ohm SMB in stock, they will ship the same day as they are ordered.
-
Product
75 Ohm BNC Connectors
-
Pasternack 75 Ohm BNC connector category contains many part numbers, most are RoHS and REACH compliant. 75 Ohm BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 75 Ohm BNC connectors are built to precise RF and microwave industry specifications. 75 Ohm BNC connector are available in male or female gender with 75 Ohm impedance. BNC 75 Ohm connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm BNC connector designs include clamp/solder, compression, crimp/solder or solder attachment methods. We offer 75 Ohm BNC connector with standard or high performance levels constructed with brass or stainless steel bodies. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm BNC connector group is in-stock. In addition to being in stock, these BNC 75 Ohm connectors will ship the same day as they are purchased.
-
Product
Qseven Rev 2.1 Application Board With LVDS, HDMI, Dual LAN And Audio
Q7B301
-
The Q7B301 is an ultra-compact Qseven reference carrier board which measures only 100 x 72 mm - the size is slightly bigger than a credit card. The Q7B301 is perfect for small box applications such as those found in the latest digital signs, kiosks and traffic control system. This Qseven application board offers various I/O connectors and flexible expansion features to reduce the design effort to the minimum. The Q7B301 also has an extended industrial grade operating temperature range of -40ºC to +85ºC to withstand the rigors of harsh environments. Axiomtek’s new Qseven Rev. 2.1 application board, Q7B301, is compatible with Qseven module – Q7M311 which is powered by the Intel® Pentium® Processor N4200 and Celeron® Processor N3350. Customers can emulate required functions on Q7M301 as a reference design board or integrate the Q7M301 directly into their product as the application board. Its minimum footprint also enables the maximum potential. The Q7M301 is especially suited for industrial IoT applications such as industrial control, medical imaging, digital signage, gaming machines, military, and networking. The Q7B301 comes with two PCI Express Mini Card slots and one SIM card slot for wireless communication (3G/4G, GPS, Wi-Fi and Bluetooth). For enhanced or high-definition audiovisual devices, the Qseven reference carrier board supports one HDMI and LVDS interfaces as well as HD audio and 4-channel digital I/O. More I/O interfaces include two Gigabit LANs with Intel® i211AT Ethernet controller, two RS-232/422/485, one USB 2.0, two USB 3.0, one SMBus, and one I2C. Furthermore, it has one SATA-600 interface for storage requirements.
-
Product
Analog Output/Arbitrary Waveform Generator PXI Card
GX1649 Series
Waveform Generator
The GX1649 is a 3U PXI digital to analog output board designed specifically for applications where multiple DC or AC analog outputs are required. The GX1649 offers 64 output channels with 16-bits of precision signal sourcing performance and can be used as a DC source or arbitrary waveform generator.
-
Product
ATG Program
FS-ATG
-
FS-ATG is the world's easiest ATG program - pull-down menus, online help, and test generation wizard guide new users step-by-step through the process. It takes less than 2 minutes to 'point & click' a setup program for a board full of devices.Generates Vectors Faster Than EverFS-ATG is a 32-bit Windows 98/NT/2000 application that takes full advantage of today's powerful PC's. Small devices finish in seconds and most FPGAs / CPLDs, even the largest and most complex, can develop great tests after in just a few hours.
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
Application Specific Board Bundles
AppliPaks
-
AppliPaks are fully integrated, custom configured board level embedded computing board sets combining an OpenVPX, VME, VME64x or CompactPCI single board computer with your choice of storage and / or I/O mezzanine cards, operating systems and device drivers.
-
Product
Video Mirror Board
BL-MIR540-01
-
The MicroImage MIR540 is a high performance display processor capable of mirroring the video input on the X and Y axes. Each of the four selectable inputs may be individually mirrored horizontally, vertically or both. Mirroring on both axes is the same as rotating the image 180 degrees. A color bar test function is also available.
-
Product
Embedded PCs
EPC-T Series
-
EPC-T Series are thin embedded PCs designed for thin mITX boards, including AIMB-231/215/216/225/285.
-
Product
Carrier Boards
ROM-DB5901
Carrier Board
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
Product
4K Custom Lens USB 3.0 Camera Board (Color)
See3CAM_CU135
-
See3CAM_CU135 is a 13MP fixed focus 4K USB camera board with good low light performance and iHDR support. This 4K board camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows and Linux. This 4K board camera is also backward compatible with USB 2.0 host ports.
-
Product
Intelligent Interface Card
IIB-1553-VXI-4C
-
The IIB-1553-VXI-4C is an intelligent interface card which provides 4 independent channels for full MIL-STD-1553 test, simulation and bus analysis functions on the VXI bus. All 1553A, 1553B, McAir and STANAG 3838 variants are supported. Each independent channel may be operated as a concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with a windowed Bus Monitor (BM), or as a stand-alone Chronological Bus Monitor (CBM) with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Each channel provides a variable amplitude dual redundant 1553 interface, with 2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Printed Circuit Board
RISER-PPM-1
Printed Circuit Board
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Intel Atom® Processor-Based Fanless Open Frame Touch Panel PC
SP2-EHL Series
Panel PC
- High power efficiency with Intel Atom® x6000E series processors (formerly Elkhart Lake)- 7"/10.1"/15.6"/21.5" PCAP touch screen- Wide input voltage range 9-36V DC- Full customization for fast integration with all form factors, kiosks, and all-in-one panel PC applications- Extensive I/O and function expansion through board-to-board connectors (Function Modules)- Simple cabling with optional Power Over Ethernet (60W)- Supports up to 3 displays, including integrated panel, DisplayPort, and USB Type C (Optional)- Pre-compliance EMC testing and high ESD tolerance
-
Product
6U VPX Single Board Computer
VPX6-187
-
Curtiss-Wright Defense Solutions
The VPX6-187 VPX Single Board Computer (SBC) is based on the NXP QorIQ P4040/4080 SOC multi-core processor. Available in versions with 4 or 8 cores running up to 1.5 GHz, and up to 8 GB of high-bandwidth DDR3 SRAM, the VPX6-187 SBC provides high-performance processing and a long list of features and I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
Product
PMC Carrier Module
DP-VME-5114
-
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
Product
CompactPCI® PlusIO CPU Card, Intel® XEON® E3 v6 Family
PC7-FESTIVAL
-
The PC7-FESTIVAL is a feature-rich high performance 3U CompactPCI® PlusIO CPU board with an Intel® Xeon® E3 mobile workstation processor for demanding applications. Also available with a 7th Generation Intel® CoreT processor.
-
Product
Flexible x1 PCI Express to 3 MiniPCI Splitter
SKU-070-XX
-
Flexible x1 PCI Express to 3 MiniPCI Splitter was designed to expand your modern motherboard (ATX, mini ATX etc.) that lacks a MiniPCI interface. It allows you to connect up to three 124-pin MiniPCI add-in boards to your motherboard’s standard PCI Express connector.Splitter includes 3 MiniPCI adapter boards, x1 PCI Express host board and 3 flat PCI Express cables.
-
Product
DC-DC Converters
-
TDK-Lambda is a global supplier of DC-DC converters with a broad range of power levels. The commercial off the shelf power solutions encompass industry standard board mounted products to chassis mount configurations for the Industrial, Healthcare, Information and Communications Technology (ICT), and Avionics and Defense markets.
-
Product
CPCI Test Extender 6Ux180mm
117FFE6018-0XXX
-
The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.
-
Product
Circbord
8003
-
VECTOR Electronics and Technology, Inc.
Pad per hole & peripheral ground plane.0.085” Square pads etched around each hole on wiring side.Accommodates any type DIP IC device or discrete component.Single sided board with pads and peripheral GND plane on one side only.Single-sided with no etch and plating on reverse side.
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
Single Board Computer
VME-1909
-
Curtiss-Wright Defense Solutions
The VME-1909 from Curtiss-Wright Defense Solutions is designed to be a low cost, high performance technology insertion Single Board Computer (SBC). Pin-compatible with many previous generations of Curtiss-Wright SBCs, the VME-1909 offers increased computing performance with today’s latest software advances.
-
Product
PC104 Single Board Computers
Single Board Computer
ADLINK products include the most rugged offerings in the industry, Single Board Computers (SBC) in popular compact form factors for embedded applications, and rugged systems with field-proven reliability, durability, and performance. PC/104 family products provide unmatched fanless operation over temperature extremes, resistance to shock and vibration, conformal coating, embedded BIOS, and a long product life reputation. The products continue to distinguish itself as an Extreme Rugged product for a multitude of applications. Mini-ITX embedded boards support the latest processors to deliver a high performance and space-saving platform for a wide array of embedded computing applications.
-
Product
PCI Express Gen 1 Test Backplane
SKU-015-01
-
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
Product
Multi-channel Solutions
-
Both STEMlab 125-14 X-Channel System and STEMlab 125-14 4-Input are based on our best-selling STEMlab 125-14 board and are designed for applications which enable multi-channel approach.
-
Product
I/O Input Board
VME-3123A
-
16-Bit High-Throughput Analog Input Board, 16 Channels with Simultaneous Sample-and-Hold Inputs
-
Product
MICROBLAZE Processor Board
MS 1536
-
- Virtex 4 FPGA with Embedded PowerPC 405 (PPC405) Core- Up to 450 MHz operation- Tri-mode Ethernet Media Access Controller- A/D Converter Blocks (10-bit / 200 kilo samples per second)- Select IO Technology (Wide selections of I/O standards from 1.5V to 3.3V)- DDR2 SDRAM (256MByte)- Program Storage Flash Memory (8MByte)- Data Storage Flash Memory (8MByte)- Vertex-4 FPGA PROM (4MByte)
