Cards
See Also: Extender Cards, Probe Cards, POST Cards, Test Cards, Boards, Modules
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 31.5Ω
50-298-110
Programmable Resistor Module
The 50-298-110 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
VPX/open VPX C-Frame 5 Slot 3U
-
Our 2nd Generation C-Frame offers the next level of flexibility in VPX development platforms. Not only can the customer exchange the type of card guides (convection, conduction, AFT) in a blink of an eye but now also the signal backplane. Thanks to Bi=/=Plane®technology, power and signal parts of a VPX backplane are separate PCB assemblies. This enables uncompromised signal quality along with faster turn around for the design of custom profiles.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 131k Ohm
50-293-034
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB116
-
The FAB116 features a PICMG 1.3 CPU card slot, one PCIe x16 slot, three PCIe x4 slots, three PCI, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB116 is compatible with Axiomtek's AX60551 and AX60552 chassis.
-
Product
2-Channel ADC Module
FMC122
-
Sundance Multiprocessor Technology Ltd.
The FMC122 is a Dual-Channel Multi-Mode A/D FMC, fully compliant with VITA 57.1 Standards. The card provides two 8-bit ADC channels that enable simultaneous sampling of 2 or 1 channel with a maximum sample rate of 1.25 GSPS (2-channel mode) or 2.5 GSPS (1-channel mode).
-
Product
16-Channel ADC Module
FMC116
-
Sundance Multiprocessor Technology Ltd.
The FMC116 is a sixteen-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides sixteen A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC116 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.
-
Product
72" Cable
RCONSCSI3-6
-
72” cable (with twisted pairs) transitions from the card front I/O connector on the RAR-USB, RAR-XMC, RAR-PCIE, RCEI-530, RCEI-830A, CEI-520/520A, R830RX, MAC2-VXI, RMAC-VME, P-DIS or P-SER to a SCSI-3 connector. This cable is for the RAR-PCIE, RCEI-530, and CEI-520/520A products, where the rear Discrete I/O connector utilizes the CONM50-D37 or other IDC-50 ribbon connector.
-
Product
50 Pin SGMC Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize the 50-pin SGMC connector.
-
Product
Mid Bus Probes
MBP850
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
RWR ATE MKII
MS 1111
-
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
Product
Analog Multiplexer Board
104-AIM-32 PC/104
-
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
Product
SIMRC - 8 x 4 Matrix 1-Pole
1030-R-8-4-1-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Ethernet Switch
SWI-22-10
-
Curtiss-Wright Defense Solutions
The Parvus SWI-22-10 is a rugged Commercial Off the Shelf (COTS) Gigabit Ethernet switch card optimized for size, weight and power (SWaP) sensitive embedded military and civilian computer network systems applications.
-
Product
PCI Precision Resistor Card 4-Channel, 2Ω To 102kΩ
50-297-134
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Extender
3690
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Interface Board for 100 BaseT Ethernet
40-965-911
Interface
The 40-965-911 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 8 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of 100 BaseT Ethernet signals.
-
Product
6U And 7U VPX 1 To 15 Slot Power & Ground Only Backplanes
101VPX6xxP-xxxx
-
Elma’s 6U / 7U VPX power and ground only backplanes provide a cost-effective way to design and test cards using the VPX architecture. The only assigned pins are for 3.3V, 5V and 12V power, and both ground and utility planes are defined.
-
Product
Type 12R2, 9U, 19" Rackmount, MIL-Rugged, Vertical
12R2-9U-V
-
The 9U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
Gas and Flame Detection System
Zero Two
-
Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection.
-
Product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
Digital I/O
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Ruggedized PC104+ & PCIe/104 System
Dragon
-
Excalibur’s Dragon is an advanced, ruggedized PC104 and PC104+ system in an enclosed, modular casing. The system is appropriate for use in data acquisition, recording nd control for any combination of ARINC-429, MIL-STD-1553, Serial, Discrete or similar types of communication. The modular, stack through design of the PC104/PC104+ platform allows you to build a tailor-made configuration based on Excalibur’s extensive range of boards plus any 3rd party cards of the customer’s choosing. Our engineers will integrate and test all 3rd party cards to the customer’s specification.
-
Product
CMOS Image Sensor
CIS
-
CMOS Image Sensors (CIS) allow multiple camera functions in mobile devices, automobiles and security systems. Nidec SV Probe provides both standard and advanced versions of our CIS cards employing a wide variety of materials ensuring a durable cost-saving solution that can meet the fine pitch and multi-dut challenges of these devices. Other features and benefits include: • Proprietary AC™ Alloy Probes • Reduced Damage Under the Pad • High Frequency Capability • Better Alignment StabilityOur advanced CIS card, the Multiplexer™, is offered specifically for high density and high parallel applications. The Multiplexer™ is built with cantilever needles held into place on one side and shorter AC™ probes on the other which leads to a more stable electrical characterization over other CIS probe card options.Contact your Nidec SV Probe Representative so we can help you find the right CIS product for your testing needs.
-
Product
Digital/Pattern/PE Card
PA64S
Interface Card
The PA64S represents a new level of performance and capabilities for PXI-based digital instrumentation. The PA64S offers high performance pin electronics and 16 sites of TMU/SPI/I2C/CLK generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be integrated, supporting up to 256 sites (16 boards).
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm
50-294-031
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Express Board Virtex-5 ADC Module
SMT742
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
Seismograph
GEA 24
-
GEA24 is a compact 24-channel seismograph (serializable up to 48 channels ) with 24-bit acquisition card and USB interface for external PC (not included in the supply). Suitable for all applications, GEA-24 is the reliable and economical solution for all professional uses.
-
Product
PXI General Purpose 2A Relay Module 16xSPDT, 50 D-sub
40-131-001
Relay
These low cost, general purpose electromechanical relay cards are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 pin D-Type connector plug.
-
Product
KX-155A Display Assembly Extender Card
KX155-EXT
-
The KX-155A Display Assembly Extender card will give the technician access to troubleshoot a display problem on this Bendix/King Nav/Comm. The card breaks out all pin connections with their functions silk-screened on the board. This board will allow the technician to make a more logical decision on what the problem may be. We have seen in our shop that the glass display is not always the failed componet.
-
Product
65 MHz Single Channel Driver Card
40490
-
One channel, 65 MHz driver with an output voltage capability of ±20V. There are two inputs--a standard input with up 65 MHz capability and an optically isolated input with 20 MHz capability. Either input can be selected.
-
Product
Single Slot 6U, 32-bit Precision Timing Module
VME SyncClock32
-
The VME timing card is a standard board level product of Brandywine Communications. With a single slot 6U, 32 bit precision timing module, the VME card is compatible with VME computers. Precision synchronization to various inputs and convenient timing outputs to external equipment are standard on Brandywine’s VME card.
