Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
Product
Extreme Rugged PC/104-Plus, PCI-104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM3-BT4
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
Silicon-Microphone 8Ch Auto Test System
BK9015
-
Based on the BK3011 MEMS Mic Tester, the BK9015 is our fully automatic 8 channel MEMS (Silicon) mic sweep tester. Testing up to 8 DUT's simultaneously, the BK9015 can test 8 mics simultaneously and sort them according to passing grade and cause of failure! Because it uses a sweep test, it can check characteristics for the entire frequency range. Your data can be viewed in real time or stored so you can analyze problems or trends.
-
Product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
785831-01
Controller
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
Product
Advanced Power System - DC Power Supply, 9 V, 200 A, 2000 W
N6970A
DC Power Supply
The N6970A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Ultrafast Transient Absorption Spectrometer
Harpia-TA
-
The transient absorption spectrometer HARPIA offers a sleek and compact design together with intuitive user experience and easy day-to-day maintenance meeting the needs of today's scientific world. Adhering to the standards raised by the OPRHEUS line of devices, the entire spectroscopic system is contained in a single monolithic aluminum casing that inherently ensures excellent optical stability and minimal optical path for the interacting beams. HARPIA can be easily integrated with both PHAROS / ORPHEUS and Ti:Sa / TOPAS laser systems. HARPIA features market leading characteristics such as 10-5 resolvable signals along with other unique properties such as the ability to work at high repetition rates (up to 1 MHz) when used with PHAROS / ORPHEUS system. High repetition rate allows measuring transient absorption dynamics while exciting the samples with extremely low pulse energies up to several nanojoules.
-
Product
Test Systems
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
Light Testers
-
Hall’s have designed and manufactured products for oil, industrial, farming, commercial, and transportation markets. Products such as truck and trailer light testers, bop savers, early engine warning systems, oil spinners, engine control panels, dashes for service rigs, drillers panels, and sandline controls. Halls have been involved with over the rebuilding from scratch of over twenty service rigs.
-
Product
Open Compute Project ® Protocol Test Solutions
-
The global OCP community is a collaborative forum where vendors work together to improve how computing systems connect and interact. OCP equipment takes advantage of these improvements and open source designs to increase interoperability performance.
-
Product
Energy Dispersive X-ray Fluorescence Spectrometer
Pharmaceutical Elemental Impurities Analysis System
-
Control of Elemental Impurities in Pharmaceuticals In the pharmaceutical industry, the analysis of elemental impurities is necessary to ensure the safety of pharmaceuticals. In December 2014, the "Guideline for Elemental Impurities" (Q3D) was issued by the International Council for Harmonisation of Technical Requirements for Pharmaceuticals for Human Use (ICH), consisting of representatives from Europe, the U.S. and Japan. In Japan, the "Guideline for Elemental Impurities in Drug Products" (PFSB/ELD Notification 0930 #4 from the Ministry of Health, Labour and Welfare) was issued, and will be applied to new drug products submitted for approval after April 1 2017. For 24 elements categorized in Class 1 to Class 3, residual quantities in pharmaceutical drug products must be controlled within permissible limits. Although ICP-AES and ICP-MS are used for precise analysis of elemental impurities, X-ray fluorescence spectrometers can be used as an alternative analysis method. This is because they can quantitatively and qualitatively analyze a variety of elements nondestructively, and without chemical pretreatment, unlike ICP-AES and ICP-MS systems. The X-ray fluorescence spectrometry has been adopted as a general method of analysis in the U.S Pharmacopeia and the European Pharmacopoeia. (USP<735>, Ph.Eur.2.2.37)
-
Product
Tone Generator
A15TG
-
The Shure A15TG Tone Generator is a battery-powered 700 Hz signal source used to troubleshoot audio systems by checking microphone lines for correct patching and detecting unusual noise that is present. The output level of the A15TG is approximately 42 dBV.
-
Product
4U Rackmount For EATX/ATX Motherboard For Rackmount Server Configurations.
HPC-7485
-
Supports EATX/ATX motherboardSupports up to eight SATA3 or SAS3 hot-swap HDDSupports 80plus 1U 1+1 redundant high watt power supplySupports up to eleven FH/FL expansion slots3 x 12cm system fans with easy maintenance featureSupports up to dimension 379 x 346mm mother board
-
Product
Advanced TCA
-
ADLINK vigorously promotes the advantages of the AdvancedTCA technology by providing complete platform solutions that offer high-density processing power, faster data throughput, and intelligent system management. Designed for next-generation telecom, datacom, and equipment manufacturers, ADLINK's AdvancedTCA platforms significantly reduce over-all development costs, come with extended operating lifecycles, and speed up critical time-to-market.
-
Product
Pico-ITX SBC With 7th Gen Intel® Core™ I7/i5/i3 And Celeron® Processor, LVDS And LAN
PICO511
-
The PICO511 is an extremely compact Pico-ITX motherboard featuring the latest 7th generation Intel® Core™ processor or Celeron® processor 3965U (codename: Kaby Lake). The feature-rich 2.5-inch embedded board is building flexible I/O interfaces through board to board connectors, wide temperature range in a small-form factor motherboard to fit different needs of many demanding applications in various industries. The PICO511 is perfect for system integrators who require an extremely compact embedded motherboard with great processing power and expansion capabilities. Its compact size form factor has ensured that it can fit into a variety of space constricting environments. In addition, the Intel® Kaby Lake-based motherboard was designed to withstand extreme temperatures, ranging from -20°C to +70°C (0°F to +158°F).
-
Product
PXI 2 Amp MUX, Dual 8-Channel 2-Pole
40-635-106
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
-
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
Product
High Pressure/Boosted System Automobile Diagnostics
-
Diagnostic leak detection equipment specifically designed for high-pressure, boosted, turbo, and diesel automobile systems.
-
Product
PXI 4 Slot BRIC 276x4 1-Pole (3 sub-cards)
40-560A-021-276X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
High Voltage Test Station
-
High-voltage test stations place high demands on the safety aspect. We design these test stations in cooperation with our manufacturers as self-sufficient test systems.
-
Product
Tunable System Sources
-
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. All models can reach any wavelength point within their specified wavelength in the C- and L-band range. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. The Keysight N7711A and N7714A tunable lasers are available in a compact format with half-rack width and one rack-unit height. This format makes them the right choice for high channel-count system load applications.
-
Product
Flash SATA Disk /mSATA SATA 3 SLC,MLC
FSA 300 Series
-
*SATA III (6.0Gb/s) interface*Capacity: SLC 1 GB to 64 GB, MLC 4 GB to 128 GB*iSMART disk health monitoring*Intelligent error recovery system*Write protection security*Anti-vibration mechanical design*Excellent data transfer speed*Zero mechanical interference*JEDEC standard MO-300B dimension
-
Product
Satellite & Payload Check-Out Systems
-
Rovsing delivers systems for complete satellite or satellite subsystem testing. Rovsing has developed a modular test system architecture, based on S/W and H/W modules developed by Rovsing for most common space interfaces such as Power, TM/TC, MIL-STD-1553B and SpaceWire. A dedicated test system can then be composed by configuration of the modular architecture, installation of monitoring and control software, as well as test definition and scheduling software as required. Besides reduced development time, this has the advantage that the system to a large extent consists of elements that have been validated on previous missions.
-
Product
Stop Time Measurement
-
Stop Time Measuring Instrument for safety measurements at power driven machines such as presses, shears and robots. The system is used to calculate the distance of the safety device acc. to EN ISO 13855. (2-hand control, light curtain ..)
-
Product
Spectroradiometer
CAS 140CT IR
-
Instrument Systems Optische Messtechnik GmbH
Manufacturers of high-class LEDs, luminaires and displays all over the world have for many years been placing their trust in the precise and reliable measuring results of the CAS array spectroradiometer from Instrument Systems.
-
Product
1000 Watt AC/DC Power Converter, 6U VPX
VPX56H-6
DC Converter
The VPX56H-6 is NAI's latest high power, 1000 Watt AC/DC converter which accepts either a 3Ø 115VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Optical Oxygen Sensors
-
The analyzer is suitable for direct field installation (NEMA 4X) in hazardous area (Class I, Division 2). The optical fiber sensor platform allows small inline sensors to be installed into sample tubing lines (1/4”), flow cells using NPT fittings, or directly into tanks or process lines using our retractable “hot tap” sensor design. BOS optical oxygen sensors are impervious to typical O2 poisons (H2S) and interferences (combustibles, magnetic, CO2 and H2) with high accuracy and long-term stability measurements without the need for complex or advanced sample conditioning systems. The threaded version of the optical sensor has optional Dual Seal (ANSI/ISA 12.27.01) classification for high pressure applications up to 1200 PSIG (82.7 BAR).
-
Product
Precision Modulators/Demodulators
-
Analog Devices precision modulators and demodulators support balanced modulation and demodulation, synchronous detection, signal recovery, and a range of other applications in industrial, medical, and communications markets. Our devices are specified over a temperature range of –40°C to +85°C and have the low power consumption that makes them ideal for battery-powered and low voltage systems.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 6.97kΩ
40-253-024
Programmable Resistor Modules
The 40-253-024 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Battery on-line Monitoring Tester
-
HD Power Test Equipment Co.ltd
Battery on-line monitoring system tester is a on-line battery monitoring and auto maintain system for USP,EPS, DC power supply, communication power supply . The tester has the function of monitoring and alerting for a series of parameters such as battery pack voltage, battery pack current, cell battery voltage, cell battery internal resistance, battery environment temperature, Cell Battery negative temperature and battery voltage balance, residual capacity and discharge. It can automatically maintain balance voltage, which used for on-line monitoring 2V and 12V battery.
-
Product
Aerial Monitoring System
AMS
-
The R&S®AMS aerial monitoring system is a payload for drones that provides monitoring and analysiscapabilities for transmissions that are difficult to reach by conventional mobile or handheldsolutions. Typical applications include monitoring of microwave links and interference hunting. The R&S®AMS is independent from the used drone and can operate in an interactive mode requiring a pilot and a monitoring technician as well as in an automatic mode performing predefined measurement tasks requiring only a drone pilot.
-
Product
Semiconductor Test
-
Tecap SPACE offers all the functions necessary to control test systems (ATE) for the semiconductor test. Tecap is hardware-independent and can be used with all customer-specific concepts.
