System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
Flight Control System Test Platform
-
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
EW System Test Set
MS 1107
-
PSS LRU Test Set is used to test the RWR (Radar Warning Receiver) system by simulating the input signals and testing the output signals.
-
Product
VLSI Test System
3380
-
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
-
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
-
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
Environmental Control System Test Platform
-
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Vibration Test System
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Vibration Test System is a simulation of the various environments encountered in the manufacturing, assembly, transportation and use phases of execution. It is primarily used to identify the ability of a product to withstand environmental vibrations.
-
Product
Millimeter-Wave Automated Accelerated Reliability Test Systems
nm-Wave AARTS System
-
AARTS fully integrated, automated, turnkey system provides flexibility and accuracy in determining RF and DC performance degradation with aging to predict life expectancy for compound semiconductor devices. Our millimeter-wave Automated Accelerated Reliability Test Systems (AARTS) and fixture solutions are available in standard frequency ranges from 26.5 to 67 GHz.
-
Product
Conformance Test System
TS8980
-
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
Offline In-Circuit Test Solutions
-
TestStation’s offline test systems are designed for a human operator or collaborative robot for product handling. TestStation systems scale to support from 128 to 15,000 test points. Our newest Multi-Site systems double productivity per system, reducing Capex and Opex for manufacturers.
-
Product
100GE Application & Security Test Load Module
CloudStorm
-
Keysight Network Applications and Security
Ixia's CloudStormTM is an industry-first 2.4 terabit application and security test solution that not only meets today’s need, but that of the future. CloudStorm delivers 3X-application and 4X-SSL-emulation scale over any other test system. It helps NEMs shortening their development cycles, and enterprises and data center operators find the right balance between mitigating security risks and delivering high end-user application performance. Emulate multi-terabit DDoS and botnet attacks to future-proof security solutions
-
Product
PXIe-2526 , 158‐Channel, 2 A PXI Multiplexer Switch Module
780587-26
-
158‐Channel, 2 A PXI Multiplexer Switch Module—The PXIe‑2526 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in either a 158x1 1‑wire or 79x1 2‑wire multiplexer topology. The PXIe‑2526 also features onboard relay counting for relay monitoring.
-
Product
Pogos
-
AMETEK Sensors, Test & Calibration
The pogo system uses test frames fitted below the machine base to allow testing of very large samples up to 2 x 2 m (78.7 x 78.7 in) in size, with the added benefit of optional elevated and low temperature testing capacity.
-
Product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm
50-294-022
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
G12x Tabletop
-
The G12x Receiver has four removable rubber feet below the platform and also allows for permanent tabletop mounting. Available with 15" or 20" platforms. The G12x accepts ITAs designed for both the G12 and G12x allowing versatility with your test system.
-
Product
Residential Meter Test System
RADIAN RM-17
-
The Radian Research RM-17 Residential Meter Test System offers simplicity for testing residential watthour meters. In a compact, lightweight package of 7 pounds, the RM-17 delivers accuracy and flexibility in a practical solution to watthour meter testing. The RM-17 combines simple operation, advanced data management, and exceptional accuracy to provide a cost effective approach to field testing.
-
Product
PCI High Density Resistor Card 10-Channel, 12-Bit, 0 To 4k Ohm
50-295A-121-10/12
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
-
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibrations. This unit also incorporates a new feature that allows the user to precisely set the contact force against the test specimen. This allows for even and repeatable contact force, limiting contact force induced errors. This extensometer mounts on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The gauge length for the 3549 is automatically set prior to mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.
-
Product
Half Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 395kΩ
40-251-142
-
The 40-251-142 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 395kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
±6 kV ANSI/ESDA/JEDEC HBM Test System
HBM-TS10-A
-
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*Wafer, package and system level HBM testing*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*No trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT HBM current sensor for real time transient current monitoring with 1V/A output sensitivity into 50 Ω digital oscilloscope input*Integrated DUT HBM voltage sensor for real time transient voltage monitoring with 1/200V/V output sensitivity into 50 Ω digital oscilloscope input*Integrated overvoltage protection of the DUT voltage sensor, DUTcurrentsensor and DC test interface for efficient overload protection of the digital oscilloscope and SMU during high voltage HBM testing*Integrated DC test DUT switch with automatic switch control*Integrated 50 Ω precision hardware trigger output for high speed digital oscilloscopes*Fast HBM measurements, typically 0.5s per pulse including one-point DC measurement between pulses*Eficient sofware for system control and waveform data management (fully compatible with TLP measurement data)*The sofware can control automatic probers for fast measurements of complete wafers*Compact size 145 mm x 82.5 mm x 44 mm of the integrated HBM pulse generator probehead*System controller size 483 mm x 487 mm x 133 mm*High performance and high quality components*Optionally available hardware upgrades to all HPPI fully integrated HBM/HMM/TLP/VF-TLP test systems TLP-3010C, 4010C, 8010A, and 8010C
-
Product
Automotive Test Systems
-
Ono Sokki Automotive Test Systems - flow meter, non-contact speedometer, engine tachometer, crank angle detector, and more
-
Product
In-line vacuum test systems
-
Ensuring that products meet the highest quality standards is absolutely essential in the manufacture of food, pharmaceutical and cosmetic products in particular.Leak-tight product containers have a major role to play here. Leak-tight product containers have a major role to play here. Leakages allow the contents of a container to get out, but more importantly they also allow germs to get in, rendering the contents unusable.INDEC vacuum test systems monitor containers for leak tightness fully automatically within the production process. A wide range of containers, including bottles, jars and cans as well as tubs and trays, are tested for leak tightness by means of a non-contact inspection.The means to this end is a pre-existing vacuum or a vacuum created in the container expressly for the purpose of leakage testing. Containers which are not leak-tight are reliably identified and automatically rejected.These processor-controlled test systems are highly reliable and extremely easy to use, qualities which have played no small part in making them the first choice already for many companies throughout the world.
-
Product
Distribution Amplifiers
-
A complete range of distribution amplifiers are manufactured by Precision Test Systems. A distribution amplifier is used to distribute the output of a frequency reference to many different places. Usually the frequency is 5 or 10 MHz but we manufacture distribution amps from DC to over 2000 MHz. We make some of the industries lowest phase noise products.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 122Ω
40-252-112
-
The 40-252-112 is a programmable resistor module with 2 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Hardware-in-the-Loop Test Systems
HIL
-
Our early development efforts and NI VeriStand expertise uniquely qualify us to maximize the benefits of and provide top-notch integration services for this software platform. Wineman Technology offers powerful and flexible MIL and HIL testing solutions, such as: Full range of MIL and HIL test systems. Software for testing. Software for simulating electronic control modules. Fault insertion unit (FIU)..
-
Product
Tri-Temp Strip Level Test Instrument
Apollon
-
APOLLON is a tri-temperature strip-level test system for motion sensors. It is especially designed for high-end Automotive and Industrial applications. APOLLON offers extremely good testing conditions: high stimulus and temperature accuracy and low noise level.
