Verifiers
-
Product
PNA Microwave Network Analyzer
N5224B
-
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Speed-O-Calibrator
16470
-
The Speed-O-Calibrator consists of two sections, control box and drive unit. The control box is stored inside the drive unit for easy portability. The control box weighs less than 6 lbs and is used in the cab of a locomotive to control the speed of the Axle Alternator Drive Unit. The Drive Unit drives the Axle Alternator at various speeds while the user verifies that the correct speed is displayed in the cab. The test system provides a complete test of the speedometer system, including all types and paddle lengths of Axle Alternators.
-
Product
PNA-L Microwave Network Analyzer
N5239B
-
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to8.5 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
IEC61032 Test Probe 32
CX-32
-
Shenzhen Chuangxin Instruments Co., Ltd.
Test Probe 32 is intended to verify the protection provided by fan guards against access to hazardous mechanical parts.
-
Product
RF Deluxe
ICAP/4Rx
-
ICAP/4Rx RF Deluxe is an extended version of ICAP/4Rx, including simulation capability for RF frequency design. This powerful system includes everything you need to design and verify all types of board, engineering system and IC-level design. Of course, ICAP/4Rx Power Deluxe includes Intusoft's time-tested "IsSpice4" analog and mixed-signal simulation kernel, featuring more enhancement than any SPICE kernel on the market for convergence, accuracy, speed and interactive capability.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Non Functional Testing
-
Non functional testing aims to verify the elements of the solution that are not related to a user action, for example, Failover, and Maintainability. Exactest deliver core non-functional test techniques to include:
-
Product
ATEX / FM Approved Grounding Clamps, Cables and Reels
Cen-Stat Static Grounding Clamps
-
Static grounding systems like the Earth-Rite range combine interlock control and visual indication to verified ground connection points and offer the highest levels of protection over electrostatic ignition risks. However, equipment specifiers may select passive grounding devices, like single pole clamps, to ground and bond plant equipment.
-
Product
Self testing clamps with Visual Indication
Bond-Rite EZ
-
The Bond-Rite EZ is an easy to use hand-held portable static bonding device that can quickly and securely establish and verify an equipotential bond between equipment for operations conducted in hazardous locations.
-
Product
Regression Testing
-
TestOrigen Software Testing Services Pvt Ltd.
Regression testing basically the process of retesting. Although when a developer modifies or change their software products, even a small modification can have surprising results. Due to this, all test cases are performed again simultaneously to verify whether the new changes have not brought the new bugs and all the previous functions are working properly or not. Such tests are performed manually, but some time in few test cases repetition of source code and updating is too much complicated as well the time consuming to think, so an automated regression testing tools are used.
-
Product
Electrical Calibration
GF6018A
-
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
Product
CTR Test Fixtures
-
Designed to hold electronic components or assemblies in place during testing, particularly for verifying the Current Transfer Ratio (CTR) of optocouplers.
-
Product
Energy Meter Calibration
-
Beijing GFUVE Electronics Co.,Ltd.
The process of verifying the measurement accuracy and working status of the energy meter through the actual test.
-
Product
ARINC 818 Analyser
-
iWave’s ARINC 818 Video Protocol Analyzer (VPA) instantly verifies the ADVB Packets against ARINC818 Standards. ARINC818 VPA software efficiently captures, decodes the ADVB data, and displays the ADVB data, raw video data, and error status. It is an excellent troubleshooting tool that helps to quickly detect and rectify errors in the ARINC 818-2 applications, simultaneously ensuring compliance of the system with the ARINC 818-2 standards.
-
Product
Fiber Optic Multimeters
-
Years ago, testing fiber optic connections required a fiber optic power meter and fiber optic light source. These two pieces of equipment were carried side-by-side and used together to verify a fiber optic connection was working.
-
Product
External Pacemaker Analyzer
EXPMT 2000
-
The EXPMT 2000 External Pacemaker Analyzer tests and verifies all the functions of any external pacemaker including transvenous, transcutanious (transthoracic), and Atrial and Ventricular sequential pacemakers.
-
Product
Thermal Profiler
V-M.O.L.E.®
-
The V-M.O.L.E. is a full-featured compact thermal profiler that belies its sophistication in an easy-to-use 3-channel Mini-thermocouple configuration. Ideal for VERIFICATION of PCB profile performance, 3 channels give you Hot, Cold and Sensitive component data for verifying the correct oven settings.
-
Product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
-
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
Product
Monitoring Solution for LIVE Services
ORION-OTT
-
Interra Systems’ ORION-OTT is a comprehensive monitoring solution for LIVE services and VOD assets, in the cloud or on-prem. It offers a high performance, scalable solution to verify ABR videos for monitoring both QoS and QoE. ORION-OTT also provides passive monitoring of origin server performance and end-user devices to understand recurrent issues and their causes.
-
Product
900 Hz to 110 GHz PNA MM-Wave System
N5290A
-
Single-sweep solution with compact frequency extenders Purchase as a single product solution Accurate leveled power can be applied to the device, providing the ability to sweep power Available various software application for detail analysis Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Proving Units for High Voltage Testing Equipment
-
A high quality range of proving units provide the important role of verifying the safe operation of high voltage potential indicators used by power engineers, maintenance personnel and service engineers. The proving units are essential tools for testing HV equipment before and after use.
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
Shielding Solutions
-
The highly transparent EMC shielding material Aaronia-Shield® and the high-tech EMC shielding fleece Aaronia X-Dream®, for example, offer very high EMC protection and are especially well equipped for all future high-frequency radiation sources in the high GHz range, which you can easily verify with our EMC Handheld Spectrum Analyzer. For magnetic field shielding, our MagnoShield® series offers unparalleled protection against alternating magnetic fields, such as cables, power distributors, high-voltage lines or transformers and generators.
-
Product
Signal Generator
MX-RFSG1800
-
The Maxcom MX-RFSG1800 signal generator is a simple low-cost device used to inject RF signals up to 1800 MHz into RF plant for the purpose of verifying those high frequencies are able to properly pass-through cables, passive and active devices.
-
Product
Reliability Testing
-
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
Product
Proving Unit
PRV240
-
The Fluke PRV240 provides a safe method to verify that your electrical test tool is operating properly before and after you conduct any live tests. The concept of “Test Before Touch” (TBT) involves testing your meter against a known live source before and after the actual measurement.
-
Product
Tx/Rx BenchBlade
-
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for logic card characterization.The card includes a HM-ZD male right angle connector segment for access to the Zone 2 connectors of a switch fabric or node card. Edge-launch SMA connectors are utilized for ease of test cable attachment. SMT pads are included on the receive pairs.
-
Product
DXN Portable Hybrid Ultrasonic Flow Meters
-
The Dynasonics DXN meter is a powerful tool for troubleshooting flow issues, whether you want to quickly verify the flow reading of another meter or to data log flow system values over an extended time period. The DXN portable meter has transducers that clamp onto the outside of the pipeno tapping or cutting is required. The meter can be easily moved and installed in different locations. The large color display makes it easy to read and the setup wizard walks you through the meter configuration steps.
-
Product
ENA Vector Network Analyzer
E5071C
-
9 kHz to 4.5/6.5/8.5/14/20 GHz2- or 4-port, 50 ohm, S-parameter test set Improve accuracy, yield and margins with wide dynamic range 130 dB, fast measurement speed 8 ms and excellent temperature stability 0.005 dB/CObtain design confidence through complete characterization of high-speed serial interconnects with enhanced time domain analysis option Protect your investment with upgradability across all of the options Every spec verified, adjustments included Lock in support & peak performance from the start
