Verifiers
-
product
Safety
Test Equipment to verify Safety, Quality and Compliance characteristics of electro-technical products as required by national and international safety regulatory agencies. These equipment are used to check Electrical Wiring Accessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Several of these safety test equipment are common to many standards and are required for routine 100% test purposes to ensure product safety.
-
product
PXI Resistor Module 2-Channel 2R to 131k with SPDT
40-293-134
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Refractometers
The series is developed for working with sugar related liquids (fruit juices, soft drinks、 wine), help monitor and control sugar concentrations in foods and beverages. Whether users are checking the "ripeness" of fruit in the field, verifying product quality after harvesting, or controlling concentrations during processing and packaging, refractometers provide critical information to ensure product quality. But,it is also commonly used for controlling the concentration of various industrial fluids cutting lubricants and flux rinsing compounds). Full ranges of measurement is available.
-
product
Battery Discharge Test Unit
125V DC 100A
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
product
DGN Advanced Reporting Feature, GTE 10.00p
K8223A
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
MIMIC sFlow Simulator
MIMIC sFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
product
Proving Unit
PRV240
The Fluke PRV240 provides a safe method to verify that your electrical test tool is operating properly before and after you conduct any live tests. The concept of “Test Before Touch” (TBT) involves testing your meter against a known live source before and after the actual measurement.
-
product
The Verifier
VC-2
Portable, battery operatedHighly accurate DC outputVerify any DC VoltmeterBattery test LEDWorks with T&R
-
product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
-
product
Partial Discharge Pulse Calibrator
TPK
Partial discharge puls calibrator TPK is a battery-powered handheld device for determining the correction factor in a Partial Discharge test circuit and to verify the Partial Discharge measurement.
-
product
Network Toner & Probe Kit
MT-7028
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
LCD Cable Length Toner & Prope Kit
MT-7071K
The MT-7071K Included 8+1 remote units, let you measures cable length up to 1200M (4000ft), and locate and verify the cable status and troubleshoot wiring. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
RTM ThermalBlade
This ATCA compatible design offers the flexibity to verify the thermal characteristics of your Advanced TCA chassis, logic cards and backplane designs. Used in conjunction with the ThermalBlade the RTM emulates a typical rear mounted logic card. Application component heights and features, airflow resistance and enclosure power dissipation can be evaluated and analyzed.Maximum sustainable watts are 113 with two switches turned on. Watts are dissipated throughout the entire RTM ThermalBlade equally.
-
product
ICP® Shock Accelerometers
Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.
-
product
FlashCheck TCT
Digital Thermocouple Thermometer Kit is an expanded range, handheld instrument used by food service professionals and quality control inspectors to verify temperatures of foods and equipment throughout preparation, storage, and handling of food. This digital thermometer kit gives you maximum durability and versatility that can be used in a variety of situations.
-
product
Structural Testing
Structural testing is used to verify the static strength, or fatigue strength, of a component by applying measured loads. Testing can be done to failure, to contractual requirements, or to validate finite element model predictions.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm With SPDT
50-293-121
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Pressure and Force Measurement Systems for R&D, Testing, and Quality Assurance
Tekscan is the leading manufacturer of tactile pressure sensors and measurement systems. Our pressure mapping systems are used by product designers and test engineers throughout the research, design, testing, and manufacturing cycle to verify and enhance product performance. The informative data allows companies to save money in design, design verification, reengineering, and machine set-up costs.
-
product
Information Technology Testing
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing information technology products according to applicable standards. We help you not only verify the classification of your product, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Multichannel Data Loggers
Check Your Solar Power Levels and Verify Integrity to Solve Power Loss Problems
-
product
Conformance Calibration Standard Test Card for GS1-128 Symbol Verifiers
AI-CCS-128-E Rev B
This test card is ideal for testing of verifiers, scanners, and other GS1-128 barcode reading equipment. It also can serve as an excellent training aid to ensure new operators are using the proper methodology and are proven competent in the use of verifiers.
-
product
Digital Multimeters
Measures and verifies multiple electrical quantities, including voltage, current and resistance.
-
product
Improving The Data Integrity Of Spectrometers
Data integrity refers to the completeness of data, with nothing missing or inconsistent. In other words, not only the data itself but also the metadata (the results of work that require human intervention, such as specifying conditions and analyzing analysis data) must be presented in a visible form, and verified together with the data. This is achieved by the Report Set.
-
product
Engine Performance Analyzer
H337H-2
Verifies engine performance during troubleshooting and after module replacement
-
product
Industrial Electronics Testing for Smart Devices & More
As more and more devices are being designed with inherent intelligence and the ability to connect and communicate, the amount and complexity of electronic content is continuously increasing for our industrial customers. They need the ability to quickly and efficiently verify proper operation of these products as they flow off the production line. Circuit Check responds to these needs by offering a wide range of industrial electronics testing solutions from consulting to complete test system and software design. We also offer adaptable support solutions to ensure proper equipment operation throughout its life cycle.
-
product
Camera Testing
FLIR
CI Systems' FLIR turn-key test stations carry out all the necessary tests to verify and compare the quality of an infrared/thermal camera. The FLIR test systems are based on CI Systems' NIST traceable blackbody radiation sources, collimators and special thermally controlled targets, designed to provide very accurate IR test patterns. All these combine to project standardized targets with known geometry and intensity to the Unit Under Test(UUT).
-
product
Automated Measurement System
EVG®40NT
The EVG40 NT (stand-alone tool) and the AVM (HVM-integrated module) enable measurement of lithography relevant parameters like critical dimension, as well as bond alignment accuracy.Because of the high-measurement accuracy, it is possible to verify compliance to tight process specifications and instantly optimize integrated process parameters.
-
product
Automatic Calibration Module
ACM4509
ACM4509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full four-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
