Motor Test
See Also: Motor
-
Product
Power Analyzer
-
E-Mobility - eDrive, and Electric Vehicle TestingAdvanced and easy to use solutions for complete electric and hybrid vehicle testing in the development, validation and production phase. One-stop solutions for electric motor and inverter testing, battery and battery charge testing, combustion analysis, hydrogen engine testing and more.
-
Product
High Power & Voltage Pack Testing System
FTF
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery Packs
-
Product
Performance Dynamometer
-
The MD-250-HD was designed to be a performance dynamometer first, with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD can boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD with 900-hp worth of loading capacity for steady state testing.
-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
Circuit Tester
69105
-
Tests circuits rated from 80 to 600 volts AC/DC.High-visibility neon lamp indicator.High-impact, sealed 5-11/16'' (144 mm) probes on long 24'' (610 mm) leads for convenience in testing motors, fuses, relays, switches, etc.Resistor between each probe and lead.Reliable electronic components.
-
Product
Transmission Performance/Endurance Test System
-
This system is suitable for vehicle drive test with only the transmission unit in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling engines, tires or vehicles other than transmission. The engines, tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
Pump Testing with NPSH Measurement
-
Test field for centrifugal and side channel pumpsfor split-case pumps or as a complete unit with customer engine.*Open tank system for recording QH characteristics*Vacuum-resistant container for NPSH measurements*Three flexible test cars with height-adjustable test motors: 5/30/90 kW
-
Product
Motor Octane Testing
DewTrak II MO
-
DewTrakII MO dew point/humidity transmitter is an optical chill mirror hygrometer designed to continuously measure the moisture content and Barometric pressure in the motor octane testing process. It is used to monitor and ensure compliance with test
-
Product
Motor/Generator Testers
-
Appliance motors are always evolving and the final testing of those motors gets more complicated every year. We build fully automated testers for domestic or offshore manufacturing facilities that can perform any amount of motor testing that you require with limited interaction by the operator.
-
Product
Drive-Train/Power-Train Performance/Endurance Test System
-
This system is suitable for engine drive test or transaxle test of HEV/EV in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling a real tires or an engine. The tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
4 Quadrant Dynamometer Test System
-
Magtrol’s 4 quadrant motorized dynamometers provides expanded testing flexibility over a typical braking dynamometer. With the ability to bring the motor under test (MUT) to synchronous RPM before beginning a test, repeatability is improved. Since the motor windings are at ambient temperature before starting a ramp test, wattage is more consistent.
-
Product
Motor Testing Solutions
-
IES Systems, Inc, is a turnkey motor testing solutions provider with 10 years of proven experience in the design and manufacturing of motor testing equipment. We provide custom designs to meet our customers' testing requirements. IES Systems, Inc. designs and builds no-load motor testers, full load motor testers, dynamometers, core-loss testers and ECM testers
-
Product
50 Channel Linear Vibration Motor Aging Unit
BK2021
-
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
Product
Testing Aerospace Motors
-
Magtrol designed this Custom Motor Test System for the testing of various aerospace motors for both commercial and military applications.
-
Product
Motorized Test Stands
-
AMETEK Sensors, Test & Calibration
Our motorized test stands are optimized for production floor operation. They provide a constant test speed and require a force gauge to be integrated with the test stand.
-
Product
Automatic Safety Test System
LS9955/56
-
The LS9955/LS9956 Automatic Safety Test System is according to GB4706.1, IEC/EN60335-1, UL60335, GB7000, IEC60598, GB4943, IEC60950 and GB9706.1. It used for luminaries, home application and motor tools safety test in production line or Lab R&D.
-
Product
Cogging Test System
CTS
-
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
AC Motor Tester
AIP892X series
-
Qingdao AIP Intelligent Instruments Co., Ltd
This product is suitable for electrical performance testing of all types of motors, such as home appliance motors (washing machines, air conditioners, fans, etc.), pump motors, stepper motors, etc. One-stop testing completes all set items, stable, fast, efficient and accurate, widely used by domestic and foreign enterprises.This AC motor tester test items: AC Hi-pot, insulation resistance, surge, DC winding resistance, no-load characteristics, low voltage start, locked rotor, rotation, PG characteristics.
-
Product
AUTOMATIC WINDING TEST SYSTEM
VE9036SU
-
6 CHANNEL Microprocessor based Automatic Test System for Automobile Coils, Magnetos, Alternator, Motor Winding. Can Test : Impulse Winding Tester (IW), AC/DC HiPot, Insulation Resistance (IR), Inductance (L), DC Resistance (DCR)
-
Product
Brushless/Servo/Stepper Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to brusheless, servo,stepper motor performance test.
-
Product
Surge with 3 Phase Transfer Switch Consoles
TC Model
-
(Surge with 3 Phase Transfer Switch Consoles) Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TC" Model has the same characteristics as the "C" Model, but includes a Built-in 3 Phase Test Selector Switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
NI-9244, 400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module
783106-01
Voltage Input Module
400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9244 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, industrial machinery, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9244 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta. You can incorporate the NI‑9244 into systems to meet standards such as IEC 61010‑1, C37.90 and C37.60, IEC 60255‑22‑(1:7), IEC 60255‑1, C37.188 Class M and P, EMC section of IEC 60870, EMC sections of IEC 61850, IEC 61000‑4‑30 Class S, and IEC 61000‑4‑7.
-
Product
Wireless TRMS Clamp Meter w/ 3-Phase & Imbalance Motor Tests
DL599
-
UEi Test & Measurement Instruments
TRMS Wireless Clamp Meter w/ 3-Phase & Unbalanced Load Tests
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-01
Voltage Input Module
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
Signature Surge Tester
TSM
-
Compact cabinet that contains a multi-position carry/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or in the field. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope and includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Standalone OLTC Event Recorder – OTM-X
-
The OTM-X is the only standalone recorder using the vibro-acoustic method and motor current testing to detect ONLINE your On-Load Tap Changer’s (OLTC) malfunctions.
-
Product
Motor Drive Test Systems
-
Drive and motor systems present unique challenges for test systems and Intepro combines regenerative active electronic loads to reduce the energy needed to do the tests as well as sophisticate instruments and supply voltages to test these demanding applications and provide meaningful results for the electrical and mechanical power parameters.
-
Product
Testing Electric Pump Motors
-
This Custom Motor Test System is designed for the testing of 5 different sized electric motors used in various sump, utility, sewage, well, pool and pond pumps. All of the components mentioned above are mounted on a versatile table that can be easily reconfigured and retrofitted to any Magtrol dynamometer.
-
Product
Motor Testing Panels
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI Filly and Partially Automatic Motor Testing Panels
