Discrete I/O
-
product
PXIe-6363, 32 AI (16-Bit, 2 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
781056-01
The PXIe‑6363 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6363 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
as an 8 bit I/O Port
BL233
The BL232 has 2 commands that let you use its pins directly. If you aren't using the I2C bus, this gives you and easy 8 bit I/O port
-
product
Digital I/O
Curtiss-Wright Defense Solutions
Our digital I/O cards include interfaces to LVDS, Camera Link, Serial interfaces, and customizable I/O. Built leveraging our decades of experience producing highly rugged COTS signal acquisition hardware, our PMC and XMC modules are designed to perform reliably in the toughest operating environments.
-
product
I/O Input/Output Board
VME-4514A
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
product
General Purpose I/O Modules
HY-TTC 36X
HY-TTC 36X is a CANopen-based, cost effective, modular and user-friendly solution for extending the number of I/Os in mobile applications. This controller is best suited for different kinds of control tasks in a vehicle and acts as slave unit in a CAN-based network architecture.
-
product
FMC Expansion I/O Module.
SI-MOD32xx
The SI-MOD32xx is a family of high resolution, FMC form factor, high channel count multi function data acquisition and control modules that plug into any SI-DSP or FPGA carrier card.
-
product
True Dual-Channel Analysis on iOS
IOScope
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
product
Digital I/O Card
Axiomtek's digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports high-density on a single board, making them specifically suitable for factory automation, industrial ON/OFF control and switch status sensing.
-
product
Rear-Panel I/O Transition Module
CP3-GESW8-TM8
CP3-GESW8-TM8 is a rear-panel I/O transition module providing flexible access to CP3-GESW8 or NETernity™ CP3-GESW8N rear-panel I/O. Up to eight Gigabit Ethernet ports of the switch are accessible from the transition module's stacked RJ-45 connectors. Each Ethernet port is routed as four 100 Ohm differential pairs.
-
product
Wireless I/O & Sensors
Advantech provides wireless I/O and sensor modules to shorten the gap between the field sites and the cloud.
-
product
PCI Multifunction I/O
626
6 versatile 24-bit counters for encoders/timers with interrupt generation Fail-safe Digital I/O E-stop Relay Battery backup of counters Four 14-bit D/A outputs, 20 Khz update rate Sixteen 16-bit differential A/D inputs, 15 kHz rate Watchdog timer may be used to reset PCI bus 48 bi-directional digital signals for solid state relay boards, 40 with edge detection and interrupts
-
product
IOS App Testing
QACraft believes in crafting an amazing experience for all users. Our team of application testers helps in analyzing every aspect of your iOS app to improve the overall performance. Our iOS application testing services are highly appreciated due to our strategic plans for testing and covering every parameter that is crucial for an app to run smoothly. Our team works with you closely to help you make your app more user-friendly and free of all errors. Right from checking the compatibility to the app loading time, our team provides you with a detailed review of the app along with the highlighted issue to help you and your business eliminate the lacking factors and make your app more functional.
-
product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782260-01
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PoE-PSE I/O Board
AX93280
*PoE-PSE I/O board complies with IEEE802.3af standard via an internal cable connected to LAN port on a SBC to power an external PoE device
-
product
Receiver, G18, 18 Module For Discrete Wiring
310120101
The lightweight and rugged 18 module Receiver provides a solution that will accommodate larger ATE chassis’ (PXI, VXI, SCXI). It allows immense versatility by affording space for up to an 18 slot PXI chassis.
-
product
PCIe-7851, Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781102-01
Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7851 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7851 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
JTAG Boundary-Scan I/O Modules
SCANIO Family
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
product
PCI-6513, 64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated Digital I/O Device
778970-01
The PCI-6513 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6513 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PCI-6111, 2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777530-01
2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6111 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6111 is ideal for a variety of applications, such as … stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6111 dimensions require chassis slots that can accommodate full-length PCI modules.
-
product
PCIe-7858, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device
786457-01
PCIe, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7858 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7858 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
Profibus-DP I/O Modules
900PB Series
Each module provides a direct network interface for your I/O signals. Unlike "block I/O" devices that combine large, expensive processor blocks with snap-on I/O terminal blocks, 900PB modules handle the network interface and I/O processing in one, compact multi-channel module. This space-saving approach is very cost-effective for systems that need to add a small quantity of I/O channels at existing control sites or network to new remote sites.
-
product
USB-6351, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
781440-01
16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6351 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6351 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
I/O Modules
esd offers a wide range of compact stand-alone I/O modules for CANopen and EtherCAT. The modules of the CAN-CBX series offer the possibility of easy mounting in the DIN rail due to the InRailBus. All CANopen modules operate according to CANopen profiles in compliance with the CiA® specification CiA 301.
-
product
PXIe-6569, PXI FlexRIO Digital I/O Module
787282-01
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
product
IOS Subsystems
Analog Devices has been the leader in isolated signal conditioning for more than 20 years. ADI IOS products feature complete modular solutions for industrial signal conditioning. These products are the benchmark for isolated signal conditioners, with price and performance unmatched in the industry.
-
product
I/O
Easily customizing your system with the exact I/O you need is a crucial step which can be addressed quickly and cost effectively using one of Elma's wide range of I/O communication products. Popular board sizes include PMC and XMC mezzanines allowing customization of your system without replacing more expensive boards or filling precious slot space.
-
product
DISCRETE TMTC INTERFACE BOX
The Discrete TM/TC Box is a 6U custom 19’’ rack equipment that could be filled with 6U, 4HP plug-ins covering the main ECSS compliant discrete I /Fs. The I/O signals of this box are all arranged in the rear side of the box, keeping clear the front side: in this way no accidental operation could be performed on the box.
-
product
PMC-Parallel-IO
PMC-Parallel-IO provides 64 independent IO in one PMC slot. 64 mA open drain buffers on each IO. Two interrupt sources. External or internal clock reference. Custom state machine designs.
-
product
Room Acoustics Analysis on iOS
RoomScope
RoomScope turns your iPad, iPhone, or iPod touch into a room acoustics measurement and analysis tool. With RoomScope, you can measure a room impulse response and then calculate reverberation time, early decay time, clarity, and definition, as defined in the ISO 3382 standard. RoomScope also allows you to adjust the Schroeder decay curve integration limits with the touch of your finger and plot the calculated room parameters versus whole or 1/3-octave band center frequency.
-
product
Data Acquisition I/O Boards
General Standards Corporation is a leading supplier in data acquisition I/O boards, provides a complete family of data acquisition cards for sonar, industrial, and embedded applications on several form factors/busses, and for many operating systems. Functions available include analog I/O, serial I/O, and high speed parallel I/O.
