Accelerators
increase speed of an object.
-
Product
Serial Bus Buffers, Extenders, and Accelerators
-
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
Product
Instrument for linear accelerators and TomoTherapy® systems
QA BeamChecker™ Plus
-
The NEW QA BeamChecker Plus is a reliable and uncomplicated daily QA instrument for linear accelerators and TomoTherapy® systems.
-
Product
Accelerators
-
Our GPGPU embedded processing accelerators are powered by NVIDIA or AMD devices that are picked for their long service life support and suitability for embedded processing applications. Each GPU processor is mounted on a rugged mezzanine for upgradability.
-
Product
Oxygen Sensor Tester and Simulator
ST05
-
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
Product
Accelerometers
-
ROGA-Instruments provides a broad range of accelerometers for General applications, Seismic measurements, High acceleration and shock, Light test objects, Triaxial measurements and Industrial applications.
-
Product
Outdoor Accelerated Weathering Testing
-
Atlas Material Testing Solutions
Atlas has pioneered outdoor accelerated testing since their development of the Trac Rac in the 1950s. Atlas, primarily at its site in Phoenix, offers the variety of outdoor accelerated services that are listed below.
-
Product
3U OpenVPX™ Intel® Xeon® SBC with One Smart Function Module Slot
68INT5
OpenVPX
The 68INT5 is a 3U OpenVPX Intel® Xeon® Processor E-2276ME based embedded Single Board Computer with integrated output graphics/video & I/O expansion. Balancing high-performance with relatively low-power dissipation, the processor supports up to six processing cores operating at up to 2.8 GHz. One I/O expansion module slot is provided that can be fitted/configured with any one of the 70+ NAI smart I/O and communications function modules. Ideally suited for rugged Mil-Aero applications, the 68INT5 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
EMC Actuator for Gas + Brake Pedal
PSE-GB
-
Pneumatically operated actuator for operation of accelerator and brake pedal in vehicles. External set-point of the pedal actuator position and brake pedal force via analog voltage to closed-loop pressure regulator in external valve box.
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
Industrial-Grade Intelligent Analog & Digital Interface Modular Control Box With Arduino Compatibility
I-Pi OT2IT
Interface Module
Discover the freedom of open-source innovation with ADLINK's industrial-grade I-Pi Arduino-Compatible PLC. Say goodbye to restrictive proprietary systems and embrace the vast, versatile world of the Arduino ecosystem. Accelerate your project's journey from concept to commercialization across diverse automation and control tasks. All this, while ensuring steadfast reliability, professional-grade functionality and industry-ready performance.I-Pi-OT2IT is equipped with numerous analog and digital sensors to manage different OT devices in smart factories. It features 8x Digital inputs, 11x Digital outputs, 9x Analog inputs, and 2x Analog outputs, and can be easily controlled by Computer-on-Modules via software over Ethernet/LAN. By consolidating OT with IT, it is the ideal solution to transform your factory into a smart one.
-
Product
SmartNIC Storage Accelerator Card Zynq Ultrascale+
iW-RainboW-G35P®
-
Your product description goes here.
-
Product
Highly Accelerated Stress Screening (HASS) Test
-
HASS consists of high and low temperature and 3 axis vibration testing performed either individually or in combination.Highly accelerated stress screening is a technique for identifying process flaws in equipment during production. HASS subjects equipment to overstress conditions but at a level which does not affect design life.For assistance in designing a HASS test program contact the laboratory.
-
Product
Infiniium MXR B-Series Oscilloscope: 2.5 GHz, 8 Channels
MXR258B
Oscilloscope
MXR258B Infiniium MXR B-Series, 2.5 GHz on all 8 channels, option to integrate 8 instruments in one, hardware accelerated plotting, and fully upgradeable , including up to 6 GHz.
-
Product
Internet Of Things
IoT
-
In a world of smart, connected everything, Altair empowers you to harness the power of the Internet of Things (IoT) to accelerate innovation and unlock business value. Leveraging our dynamic toolset you can deploy edge compute clusters, train and execute machine learning models, implement complex application business logic, perform data transforms, visualize real-time data, and much more. We give you the building blocks for your digital transformation to get moving fast, scale quickly, and continue to improve over time.
-
Product
Opacimeter for the Measurement of Diesel Vehicles
MO / MAHA OPAZIMETER | VP 135043
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
Product
Accelerometers
-
Analog Devices accelerometers and iSensor® MEMS accelerometer subsystems provide accurate detection while measuring acceleration, tilt, shock, and vibration in performance driven application. Our portfolio leads the industry in power, noise, bandwidth, and temperature specifications, and offers a range of MEMS sensor and signal conditioning integration on chip. Our MEMS-based Circuits from the Lab® reference designs have been built and tested by ADI experts to help you jumpstart your next system design.
-
Product
Embedded MXM Modules
-
ADLINK’s Embedded MXM GPU modules - based on NVIDIA's embedded GPUs - can boost the performance of a wide range of workloads, including image processing and analysis, computing acceleration, and artificial intelligence (AI). ADLINK’s Embedded MXM GPU modules offer high performance, high data bandwidth, power efficiency, and longevity support in a reduced hardware footprint, well-suited for size, weight, and power (SWaP) constrained applications. ADLINK’s Embedded MXM GPU modules can increase system responsiveness and accuracy, as well as decrease latency, and are an ideal fit for industrial automation, healthcare, transportation, aerospace and defense, gaming, and telecom applications.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P | VP 230046
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
Product
Vibration Meter
-
Shenzhen Graigar Technology Co.,Ltd.
Vibration meter (also called vibration severity) uses Piezoelectric Acceleration Transducer transfer the vibration signal in to electrical signal, analyze the input signals, and show the Acceleration, speed, shift of the vibration. It is widely used in the lines of Power, petrochemical, machinery manufacturing, metallurgy, vehicles, etc.
-
Product
Azure Time Series Insights
-
Improve operations and decision-making with decades of IoT data delivered with rich visualization and a turnkey experience. Use time series data insights and interactive analytics to accelerate IoT analytics data use throughout your organization.
-
Product
Dual-Axis Accelerometer For HS5 & 6 Handyscopes, +/- 2G
TP-ACC20-09
-
The Accelerometer is a low cost, low power, complete dual-axis accelerometer with signal conditioned voltage outputs. The output signals are analog voltage proportional to acceleration. The Accelerometer is capable of measuring both positive and negative accelerations to at least +/- 2G.
-
Product
Angular Accelerometers
-
Columbia Research Laboratories
Columbia Research Labs offers Angular Accelerometers that use the fluid rotor concept of sensing angular acceleration resulting in a highly accurate precision Angular Accelerometer that provide excellent bias stability and rejection of linear acceleration. We also offer smaller electrically damped Angular Accelerometers that provide exceptional high frequency characteristics for an angular acceleration within its range of sensitivity. Lastly we offer a Variable Range Angular Accelerometer allowing the customer to change the measurement range of the sensor to meet their requirements.
-
Product
OTDR and iOLM Testing
-
OTDRs are at the core of EXFO’s optical expertise. Leading the OTDR market with a 48% market share and the broadest OTDR portfolio, EXFO offers an OTDR built smart for any type of network. Based on field knowledge and 20 years of OTDR expertise, EXFO’s OTDRs are designed to meet network operators’ latest requirements. Combining intelligence and accuracy with user-friendliness, our solutions require minimal training and provide you with measurements you can trust, minimizing truck rolls and accelerating workflow in the field. Innovation is front and center at EXFO, and the iOLM is a prime example of a game-changing solution. The iOLM lets you take advantage of the full power of your OTDR, bringing automation to a new level—and enabling even the untrained technician to become a test expert in no time.
-
Product
Digital Signal Processor Card for PCI bus
SI-C33DSP
-
The SI-C33DSP-PCI from Sheldon Instruments is a powerful Digital Signal Processor (DSP) card for your PC equipped with a PCI bus. It is based on Texas Instruments’ new 150Mhz TMS320VC33, 32 bit floating point DSP, and can transform your PC into an ultra high performance development system and DSP accelerator.
-
Product
Radio Access Network
RAN
-
Break free from traditional restrictions of proprietary networks with Radisys Connect Open RAN protocol software and accelerate 5G deployments.
-
Product
Digital Accelerometer
ZET 7152-N-VER.1
-
Digital accelerometer ZET 7152-N-VER.1 has a compact triaxial sensing element; it is purposed to measure linear acceleration and vibration acceleration variable component in three mutually perpendicular planes. Light weight of sensing element (only 1.5 g) considerably decreases self-mass load effect, and compact dimensions (8.5×8.5×8.5 mm) allow using ZET 7152-N-VER.1 digital accelerometer to measure vibration in small work-area systems.
-
Product
PCI Express Graphic Card with NVIDIA® Quadro® P4000
Quadro-E PEG P4000
Graphics Card
The Quadro-E PEG P4000 perfectly balances performance, features, and compact form factor to deliver exceptional creative experience and productivity across a variety of 3D applications. The Pascal GPU with 1792 CUDA cores, 8GB GDDR5 onboard memory and support for up to four 8K (7680×4320 @ 60 Hz) native displays accelerate product development and creation workflow demanding fluid interactivity for large, complex 3D workpieces.
-
Product
COM Express Type 7 Basic Size Module with Intel® Xeon® D-1700 Processor (formerly codename: Ice Lake-D)
Express-ID7
Computer on Module
ADLINK’s Express-ID7 COM Express Type 7 Basic Size module is based on the Intel® Xeon® D-1700 processor and features integrated high-speed Ethernet for up to 4x 10G combined with 16 PCIe Gen4 lanes for instantaneous responsiveness and performance. Equipped with Intel® TCC, Deep Learning Boost (VNNI), AVX-512 technologies for optimal, accelerated AI performance, and support for Time Sensitive Networking (TSN), it provides precise control of hard-real-time workloads across all networked devices.
-
Product
Tactical Grade Inertial Measurement Unit (IMU)
ADIS16490 iSensor
-
The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.
