Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
200-Pin LFH Cable Connector, Bottom Exit, Male
C200LMB-2SP-5A
This connector with bottom cable exit shell is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector.
-
product
PXI Single Microwave Transfer Switch 40GHz 50 SMA-2.9
40-782A-541
The 40-782A-541 is a single transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 40GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
PXI Very High Density MUX 49 Chan 4 Pole
40-675-002-49/4
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 12.4GHz, 50Ω, N-Type, Remote Mount
40-780B-512-E
The 40-780B-512-E (PXI) and 42-780B-512-E (PXIe) are dual SPDT 12.4GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
product
9-Pin D-Type Female Connector
92-960-009-F
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
product
XMC-to-PCI Express Adapter
7988
The Technobox, Inc. P/N 7988 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 7988 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
product
20-Pin GMCT Cable, Male to Male, 10A, 1m
A020GMR-020GMR-0B100
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Outdoor AGC Optical Node
SR814WA
Hangzhou Softel Optic Co., Ltd.
*SR814WA series of 1310nm optical relay station is a two-way optical connector with HFC network engineering experience and equipment development experience accumulate for many years by ourselves only for HFC two-way Broadband Network. This product is designed with full consideration of network topological structure.The building block system modularized structure is adopted in SR814 Series *Field Optical Work station. It has flexible configuration and convenient debugging, and solves engineering and technical problems of collecting noise with two-way return path network. And it meets the requirements of modern CATV business network security transmission with high reliability of FTTB (Fiber to the Building).*SR814WA and SR814WB Optical Workstation are four way independent output models; WR-8604HB and WR-7504HB Optical Workstation are two way independent output models.*SR814WA Optical Workstation is our latest flagship product. Advanced optical AGC control circuit adds to the part of optical receiving to ensure the input optical power as low as -9dBm.
-
product
In-Line Isolator Single Stage 1310nm Bare Fiber 250μm Without Connector
IL-S-31-25-05-OO-3422
Guilin GLsun Science and Tech Group Co., LTD
Center Wavelength 1310 nm PDL ＜0.1 dBPMD 0.25 ps Dimension Φ3.4×22 mmOperating Temperature -5 to +70°C Storage Temperature -40 to +85°C
-
product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 37-Pin D-type Connector
40-158-104
The 40/42-158-104 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
44-Pin D-Type Female Connector
40-963-044-SF
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
PXI Matrix Switch: 8x32, 1-Wire, 100Vrms/2A, Armature Relays
M9122A
The M9122A is an 8x32 full crosspoint switch matrix offering high-voltage switching in a high-density PXI module. This module allows for higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This module is configured with a common ground. The durable armature switches are capable of switching up to 100Vrms, with up to 60W of power. The 8-wide bus can be used to route signals between your instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
product
CTEL 6U 5 slot with ATX, P1P4s, P2P3P5l, RoHS
104CTEL605-4046R
CompactPCI CTEL 6U 5 slot with system slot left, H110 bus, ATX connector, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
product
PXI 16x2 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-728-002-L
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
product
High Density Modular Connector
L Series
The L Series comes with frames in various lengths to accommodate a variety of module combinations. The frames range from a basic frame with just 2 side rails and 2 end caps, to more complex versions with jackscrews, backshells, cable clamps, etc.
-
product
32-CH DI & 32-CH DO 12 MB/s High-Speed Card
PCIe-7200
- x1 lane PCI Express interface- 32-CH TTL digital inputs and 32-CH TTL digital outputs- Up to 12 MB/s transfer rate- Onboard programmable timer pacer clock- Support handshaking digital I/O transfer mode- Bus-mastering DMA for both digital inputs and outputs- 5 V power available on connectors- Compact, half-size PCB
-
product
Rear-Panel I/O Transition Module
CP3-GESW8-TM8
CP3-GESW8-TM8 is a rear-panel I/O transition module providing flexible access to CP3-GESW8 or NETernity™ CP3-GESW8N rear-panel I/O. Up to eight Gigabit Ethernet ports of the switch are accessible from the transition module's stacked RJ-45 connectors. Each Ethernet port is routed as four 100 Ohm differential pairs.
-
product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 2x96 Male SCSI Connector
510109591
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x96 Male SCSI Connector
-
product
Industrial Connectors / Han®
Rugged, rectangular, heavy-duty plugs and sockets used to reliably transmit power, signal, and data in harsh industrial settings, enabling modular machine setups with easy connect/disconnect for power, data, and even pneumatics in one compact system.
-
product
PXIe-2544 , 6.6 GHz, 50 Ω, Solid-State, 8x1 PXI RF Multiplexer Switch Module
780587-44
PXIe, 6.6 GHz, 50 Ω, Solid-State, 8x1 PXI RF Multiplexer Switch Module—The PXIe‑2544 features high-performance solid-state relays that offer unique benefits such as unlimited relay life and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel.
-
product
PXI 2 Amp MUX, Single 16-Channel 2-Pole
40-635-102
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Low to Modest Volume Clean, Inspect, Test
KI-TK034
1310/1550 nm source & power meter, inspection microscope, cleaning materials. Interchangeable MPO/APC, SC, LC connectors (EAR99 Restricted)
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
Cable Assembly, 50-Pin D-Type, Female to Female, 2m, Exit Away From Pin 1
40-970-050-2m-FF
The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Cut Ends, 2m
A015DM5-C-0A200
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
6U CPCI Rear Transition Module With Rugged M12 Connectors, CPCI-RMPSA
20040269
The cPCI-RMPSA is a 6U CPCI Rear Transition Module with ruggedized M12 connectors that supports ADLINK 6U CompactPCI processor blades.
-
product
Eurocard Plugbord
4616, 160-PIN VME64x
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 160-pin DIN connectors. 3-Hole Solder Pad Pattern on both sides. 3-Hole Solder Pads (0.28” x 0.080”) for interconnecting multiple component leads.Interleaved buses on both sides, back-to-back. Pad and bus surfaces solder-coated for user convenience. Row and column legends provided.
-
product
RTSI Bus Cables for 4 PCI or AT/ISA Devices
776249-04
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
product
PXI 9 x SPDT RF Switch 500MHz 50 Multiway Connectors
40-754-009
The 40-754 is a 50Ω High Density RF switch available with 17 or 9 SPDT relays in a single PXI module. The 40-754 is available with two connector options; an SMB connector that provides a frequency range of 1.2GHz (useable to 1.8GHz) occupying two PXI slots, or an MS-M RF multiway connector which limits the bandwidth to 500MHz but offers a high density solution occupying one PXI slot. The RF switch design is identical in each case.
-
product
MS-M 3-Pin RF Cable Assembly 0.5m
40-979-503-0.5m-FU
The MS-M RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
