Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-350-HI
-
The 40-230-350-HI (PXI) and 42-230-350-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Disconnectors
-
GE Vernova is a global market leader for disconnectors (disconnect switches) since 1960, with 8 product facilities in 7 countries and hundreds of thousands installations in more than 130 countries around the world. The portfolio includes disconnectors for AC applications (up to 1,200 kV), for DC applications (up to 1,000 kV) and for railway applications. We also offer power connectors to connect two or more conductors for a continuous electrical path.
-
Product
Audio Card I/O Modules
PIM481-J/DSUB
-
The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 40 GHz, 50 Ω, SMA-2.9, Failsafe, Remote Mount
40-782B-541-E
Switch Module
The 40-782B-541-E (PXI) and 42-782B-541-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 40 GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
Product
Expanding In-Circuit Capabilities
-
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
Product
68-Pin VHDCI Male to 68-Pin VHDCI Male, 80 MHz, Shielded Digital Cable
156166-01
High Speed Digital Cable
The SHC68-C68-RDIO2 is designed and shielded specifically for the digital I/O connector on the USB-7855 and USB-7856 Multifunction Reconfigurable I/O Devices. This cable features digital I/O lines individually twisted with digital ground for high-signal integrity and noise immunity. The SHC68-C68-RDIO2 is available in 1 m and 2 m lengths.
-
Product
NI 9980 10-Pos Spring Terminal (qty 10)
197991-01
-
10-Pin, Male COMBICON to 10-Pin, Female Spring Terminal Block Plug - The NI-9980 consists of a bag of 10 spring terminal plugs for any 10-position C Series module. These terminal plugs provide direct connectivity to the module. All C Series modules ship with the required connectors, so you can purchase the NI-9980 to add spring terminal connectivity, reduce wiring on multiple devices, or use for spare replacements.
-
Product
6U Processor Blade
CP62007
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62007 is a 6U processor blade based on Intel’s 4th generation core i7/i5 processors using 22nm process technology, supporting up to four cores / eight threads at 2.4GHz. CP62007 supports up to 16GB onboard soldered low voltage DRAM with ECC. It also offers up to 64/128GB SLC/MLC onboard SATA SSD for installing operating system and drivers. The onboard design of memory and SSD enhance the anti-shock and vibration performance dramatically.CP62007’s onboard processor integrates Intel® HD Graphics 4600 controller, supporting a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA. And the VGA resolution is up to 2048x1536. With HDMI/DP/eDP outputs, the resolution can be up to “4K”.CP62007 supports 1x VGA and 2x DP/HDMI/DVI, up to 3 independent or cloned displays.CP62007 uses high speed CPCI connectors on J3 and J4 position for transferring high speed serial signals, such as PCIe2.0, USB3.0 and SATAIII. And the foot-print of high speed connectors are fully compliant with CompactPCI specifications.
-
Product
Step Attenuator
RSC
Attenuator
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
Product
Cable Assembly 44-Pin D-Type Male to Unterminated With Tinned Ends, 1m
A044HM5-T-0A100
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.
-
Product
Streamer Cables
-
Teledyne Marine Geophysical Instruments
Over the years, analog and conventional diameter digital streamer systems from Geophysical Instruments have set the commercial benchmark in the marine geophysical industry.More recently, we have proudly established a new benchmark with the SDS-55 Small Diameter Streamer Array. The SDS-55 utilizes liquid crystal polymer stress members, a novel spacer approach, waterproof hydrophones, and ingenious connector designs. This design yields the most robust fluid-filled streamer in the industry.
-
Product
PXI 2 Amp MUX, Dual 4-Channel 4-Pole
40-635-107
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Cable 100-Pin Micro-D Male to Unterminated, With Ferrules, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-F-9A200
Cable Assembly
This 2m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 40 GHz, 50 Ω, SMA-2.9, Internal Termination, Failsafe
42-781A-422
Relay
The 40-781A-422 (PXI) and 42-781A-422 (PXIe) are dual failsafe SPDT 40 GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8491B
Attenuator
The Keysight 8491B coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. It has type-N connectors with a maximum frequency of 18 GHz. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
PXI High Density Multiplexer, 20-Bank, 8-Channel, 1-Pole
40-615A-001
Multiplexer Module
The 40-615A-001 is a 20-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
Thermocouple Thermometer Data Logger
HD2108.2
-
Thermocouple thermometer with logger. Input for K, J, T, R, N, S, B, E type probes with miniature connector. Maximum, minimum, average.
-
Product
FPC Test Connector Clip Connectors
-
FPC Test Connectors (Clip Connectors) can easily be inserted and can be used for repeat testing, saving time and money as well as minimizing damage.
-
Product
100 Pin 1.27mm Pitch Micro-D Cables - 100 Pin To 100 Pin For Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 100-pin Micro-D connector.
-
Product
Connectors & Adaptors
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger designs and manufactures connectors that are engineered to reliably transmit data and power in numerous types of applications with various requirements. Whether it's high data rates, small form factors or special requirements like non-magnetic materials or special coupling mechanisms, e.g. magnetic self-mating connections, Rosenberger offers standardized and customized connector solutions to meet those requirements.
-
Product
Cable 100-Pin Micro-D Male to Unterminated, Cut Ends, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-C-9A200
Cable Assembly
This 2m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 2m
40-971B-200-2m-MM
Cable Assembly
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
PCIe/104 OneBank SBC w. Dual 1GHz ARM9
EMC²-Z7030
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-Z7030 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Z7030 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
Slip Ring Tester
-
The SRT is an automatic test system offering fast and accurate measurement and reporting of noise, contact resistance and insulation resistance. It’s been designed to improve QA for manufacturers of slip rings, commutators, rotary connectors. It can also be used to test devices coming back for repair and overhaul.
-
Product
LXI Microwave Multiplexer, SP4T, 7-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-803-507
Multiplexer Module
Our 60-803-507 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
RF Antennas
-
These antennas are specially designed for IoT devices, are easy to implement, and provide high efficiency and performance. RF antennas are available in several configurations, with options for the number and range of frequency bands, antenna construction, and RF connector mating interfaces.
-
Product
Mini Array+
DORC's ZX-1
-
Direct Optical Research Company
Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.
-
Product
20-Bit, 1MS/s/ch (16 AI, 2 AO, 16 DIO) MioDAQ, USB Multifunction I/O Device
789889-01
Multifunction I/O
USB-6451 (OEM), 20-bit, 1MS/s/ch (16AI, 2AO, 16DIO), 50-pin Connector, Simultaneous mioDAQ Device
-
Product
Receiver, I2 Micro ICon, 168 Position, For Crimp Contacts
310130102
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 168 QuadraPaddle contacts. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is made for crimp contacts. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-356-HI
-
The 40-230-356-HI (PXI) and 42-230-356-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
