Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
MS-M Style RF Connector Female Contacts RG179
40-969-701-FC
-
This is a 30 piece kit of RF Connector Female Contacts for MS-M style Connector Housing, suitable for RG179 Co-axial Cable.
-
Product
High Voltage 9 Pin D-Type Cables - Connector to Connector for Pickering
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 9-pin D-type connector.
-
Product
Cable Assemblies
-
VPC Cable Assemblies provide a reliable interconnect between the instrument and receiver interfaces. Connector‑to‑connector cable assemblies are also available.
-
Product
Signal Generator
8005
-
5 digit BCD, 1 latch control line, 25 pin female, D type connector. Normal switching mode, SSB phase noise will be degraded in the fast mode.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 50 GHz, 50 Ω, SMA-2.4, External Termination, Failsafe, Remote Mount
40-781A-722-E
Relay
The 40-781A-722-E (PXI) and 42-781A-722-E (PXIe) are dual failsafe SPDT 50 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
10-meter (33 feet) Sensor Cable
E1739B
Calibration Cable
The E1739B 10-meter (33 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.Other cable lengths available: E1739A 5-meter (16 feet), E1739C (49 feet) 15-meter and E1739D 25-meter (82 feet).
-
Product
Block Down-Converter
BDC Series 5” x 2.5” x 0.6”
-
*Connectorized Package *Compact, Rugged Design *Custom Designs Available *Internal Low-Noise LO *Automatic Switchover to Internal Reference ifExternal Reference is Removed
-
Product
Cable Assy 9-Pin D-Type, F/F, 0.5m
40-970-009-0.5m-FF
Cable Assembly
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 50 GHz, 50 Ω, SMA-2.4, External Termination, Failsafe
42-781A-721
Relay
The 40-781A-721 (PXI) and 42-781A-721 (PXIe) are single failsafe SPDT 50 GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Data Broadcast Units
-
The DBU-TTL Data Broadcast Unit is designed for use in receive only data broadcast applications. The unit supports 8-Ports Data/Clock distribution of TTL signals on BNC connectors. 1U rack mount chassis.
-
Product
SparkFun RJ45 MagJack Breakout
-
This is the SparkFun RJ45 MagJack Breakout, a simple board that will provide you with a way to put an ethernet port into your breadboard. The SparkFun RJ45 MagJack Breakout is the same one found in our very own mbed Starter Kit and breaks out each pin from the ethernet jack. This rev of the breakout is equipped with the RJ45 MagJack connector already soldered to the board which mean you no longer need to solder the connector to the board yourself or worrying about buying them separately!
-
Product
25 Pin Breakout Interface
VSI-Breakout-25
-
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-515-011
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-212-M
Multiplexer Module
The 40/42-860A-212-M is a PXI/PXIe single insert/bypass switch with SC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
P19729B130G050TL106ST
1000015
-
The Pogo Connectors, specifically the model P19729B130G050TL106ST, are designed to provide reliable performance through their advanced technical features. With a pitch of just 3.00 mm (118 mils), these connectors ensure seamless connectivity in applications requiring compact and efficient connections. They operate effectively across a wide temperature range of -45°C to +200°C, making them suitable for various environments. The basic contact probe design ensures optimal functionality and longevity in demanding conditions.
-
Product
Wi-Fi Antennas
-
Our extensive portfolio of Wi-Fi antennas includes internal/embedded antennas and externally mounted antennas in a variety of formats. Options range from extremely small adhesive-backed PCB antennas for IoT devices to large MIMO panel antennas for wide area coverage. A wide variety of connector options and mounting options are available to give our customers greater flexibility. Our Wi-Fi antenna portfolio includes products manufactured by TE Connectivity, Laird Connectivity External Antennas, and Hirschmann Car Communications.
-
Product
Ball Pressure Apparatus
BP-20
-
Is designed to perform tests specified in many standards where resistance of insulating materials to elevated operating temperatures is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaires, motors, connectors, etc. The test ensures that external parts of insulating material, the deterioration of which might cause the appliance to fail to comply with the relevant standards, are sufficiently resistant to heat.
-
Product
Calibration Kit
N912
-
*N912 Calibration Kit, * Frequency Range: up to 9 GHz, * Impedance: 50 Ohm, * Connector Type: N-type.
-
Product
Chassis
RSM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or any combination or configuration such as a 16x8 matrix, 32x4 matrix or two 16x4 matrices. Matrix configurations are non-blocking and physical layer switches act like a cable connection with D connectors creating a one to one connection between D9, D15 or D25 connectors.
-
Product
Couplers
-
Macom Technology Solutions Holdings Inc.
MACOM’s couplers are used extensively in a wide range of aerospace and defense, wireless, and wireline communications applications. Our directional and hybrid couplers are offered in a variety of connectorized and surface mount packages with a broad range of coupling values ranging from 6 to 30 dB. Operating at frequencies from 2 MHz up to 18 GHz our couplers are ideal for real-estate constrained customers who need a high performing device for easy assembly.
-
Product
3U CompactPCI® Subsystem with 8-Slot Backplane and 400 W ATX Power Supply
cPCIS-2630 Series
Backplane
- 400 W ATX Power supply- 3U CompactPCI® backplane with seven peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports rear I/O backplane with P2 connectors for cPCI 50mm/80mm depth RTMs- Temperature, voltage, and fan monitoring LEDs
-
Product
High Voltage Switching Systems
HXV Series
-
HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Unterminated (Tinned Ends), 0.5m
40-972B-200-0.5m-MU
Cable Assembly
This male rear exit to unterminated 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to the product by screwlocks.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends
A050DF5-C-0A100
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Docking / ATE
-
The iDock Series is a series of connectors ideal for use with automatic machine handlers in production testing. Floating bushings allow up to .04" of re-alignment. Use with a combination of various I/O modules and a max of 5,952 signal contacts simultaneously. The iDock series is rated up to 100,000 cycles.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode
40-855A-022
Multiplexer Module
The 40/42-855A-022 is a PXI/PXIe dual 2-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Coaxial Switch, DC to 40 GHz, SPDT
8765D
Coaxial Switch
The Keysight 8765 family of switches is designed for microwave instrumentation and ATE systems and features excellent electrical and mechanical performance. The Keysight 8765D is equipped with SMA connectors and operates from dc to 26.5 GHz with 3.5mm connectors and 40 GHz with 2.4 mm connectors. Option 292 can be ordered with Keysight 8765D. It is available with voltage option covering any drive voltage between 4.5 volts and 32 volts dc. Where performance data are required, Option UK6 includes a printout of test results. This switch is designed from the ground up for maximum dependability and performance. It is designed to operate within its specifications for more than 10,000,000 cycles.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode
40-855A-222
Multiplexer Module
The 40/42-855A-222 is a PXI/PXIe dual 2-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Additional Products: 3 Pin Power D-Type Cables - Connector To Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Failsafe
42-780B-753
Relay
The 40-780B-753 (PXI) and 42-780B-753 (PXIe) are triple failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
