Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
PXI/PXIe Power Relay Module, 32xSPDT, 5 Amp, 50-Pin SGMC Connectors
42-158-001
Relay
The 40/42-158-001 is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
Product
PXI High Density Multiplexer, 5-Bank, 16-Channel, 1-Pole
40-615A-015
Multiplexer Module
The 40-615A-015 is a 5-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
Single 24-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-101
Multiplexer Module
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-112-HI
-
The 40-230-112-HI (PXI) and 42-230-112-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 122Ω with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
-
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-155-HI
-
The 40-230-155-HI (PXI) and 42-230-155-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI Optical Switching - 1:1 Multiplexer (SPST) Plugin Module
65-281-380
Multiplexer Module
The 65-281-380 1:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, FC/APC Connectors, With Interlock
42-850A-014-M50-HI
Multiplexer Module
The 40/42-850A-014-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a 68-pin micro-D connector.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 24 Channel
41-761-002
Simulator
The 41-761-002 is a low voltage 24-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber
40-850A-314-M50-HI
Multiplexer Module
The 40/42-850A-314-M50-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Bonnet EFS for Horizontal Wellhead Completions
-
This Electrical Feedthrough System design provides a high-reliability circuit for transmitting electrical signals from downhole gauges through the wellhead and Subsea Tree to the Subsea Control Module (SCM) for topside monitoring. The system incorporates Teledyne DGO's high integrity glass-seal technology in three critical pressure barriers for maximum long-term reliability. The feedthrough system creates a permanent connection to the Subsea Control Module when the tree is installed onto the wellhead. In addition, a permanent rig-based DHG cable termination is completed to connect the control line to the feedthrough system. The DHG connector is available with a variety of sealing packages, including fully testable, dual metal-to-metal sealing of all downhole tubing hanger interfaces.
-
Product
Output Signal Cable
Co10-SE
-
The Output Signal Cable Co10-SE is meticulously designed for use with SENIS 3DACMT magnetic transducers, ensuring reliable connectivity and optimal performance. This cable features a tough construction with a 4mm standard banana plug connector, facilitating secure and efficient signal transmission. The layout of the signal wiring includes color-coded outputs for the X, Y, and Z axes, alongside a dedicated ground connection, which simplifies the installation and troubleshooting process for users.
-
Product
XMC-to-PCI Express Adapter
7764
-
The Technobox, Inc. P/N 7764 XMC to PCI Express Adapter permits the use of a single-wide XMC module with VITA 61 (XMC 2.0) style connectors in a 8x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors.
-
Product
Audio Generator
AG-51
-
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber
40-852A-218-HI
Multiplexer Module
The 40/42-852A-218-HI is a PXI/PXIe 8-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
3U Processor Board
CP32108
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP32108 is a compact modular 3U CPCI single board computer compliant with CompactPCI specification. Based on Intel® 6th Skylake-H platform, CP32108 supports a variety of processors. On CP32108, there are rich interfaces like SATAIII, USB3.0, GbE, PCIe2.0, etc. In addition, CP32108 can provide up to 1TB SSD storage with mSATA interface.CP32108 applies high-speed CPCI connector on J2, in order to transmit PCIe2.0, USB3.0, SATAIII signals. CP32108 supports up to x4 PCIe to rear with flexible PCIe configuration including 1 x4, 2 x2, 1 x2+2 x1 or 4 x1.CP32108 integrates Intel® Gen9 HD Graphics P530 display controller, and supports various display outputs like eDP, DP and HDMI(with resolution up to 2560x2160 @24Hz, 24 bpp).
-
Product
Polarization Maintaining Fiber Components
-
OZ Optics offers a broad range of polarization maintaining components, patchcords, and connectors designed to resolve polarization problems, which are becoming increasingly important in today's higher speed and more complex mesh optical networks. By maintaining the polarization of the signal at its source, our polarization maintaining components minimize polarization mode dispersion and eliminate the effect of polarization dependent loss thereby increasing the quality of the signal that is transmitted throughout the network.
-
Product
Optical Power Meter for 400-1550 nm Wave
F-712.PM1
-
Physik Instrumente GmbH & Co. KG
This photometer can convert an optical signal into a voltage signal in high resolution and with an extremely high bandwidth. The design of the optical input enables measuring of the optical signal independent of the position of the optical fiber in the connector. Wavelength range: 400 to 1550 (1) nm
-
Product
Bulkhead Penetrator for Subsea Applications with 4, 7, or 12 Circuits, 30 A
P1.7-30 Electrical Penetrator
-
ODI's P1.7-30 penetrators meet the same electrical performance characteristics as Nautilus connectors and are used where the need to mate and demate is not necessary, generally at the second end of a pressure-balanced oil-filled (PBOF) assembly with a Nautilus connector at the opposite end. The Penetrator is typically attached directly to a vessel, which can be either pressure balanced or at 1 ATM.
-
Product
PCI Express Digital I/O Boards
PCI-P8R8
-
PCI Board with 8 Channels of Isolated Digital Input and 8 Relay Outputs. Includes one CA-4002 D-Sub connector
-
Product
500 Pin SEARAY Cables - Connector to Unterminated For Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a 500-pin SEARAY (250-port) connector.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-030-HI
Programmable Resistor Module
The 40-230-030-HI (PXI) and 42-230-030-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
Product
Thermocouple Connectors
-
We are Europe's largest manufacturer of thermocouple connectors and accessories in IEC, ANSI and JIS colour codes. The full range of connectors are available from stock for immediate despatch.
-
Product
PCI Card
EXC-4000PCI/xx
-
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M4K1553PxS module is NOT compatible to the M4K1553MCH module.The EXC-4000PCI/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
Product
3U CompactPCI 9th Gen Intel® Xeon®/Core™ i7 Processor Blade
cPCI-3520 Series
Processor Blade
The cPCI-3520 Series is a 3U CompactPCI blade available in single-slot (4HP), dual-slot (8HP) or triple-slot (12HP) width form factors with various daughter boards to provide a broad range of I/O requirements. Faceplate I/O in the single-slot (4HP) version includes 1x DVI-I, 2x GbE and 1x USB 3.0 port (these I/O are common to all versions). Faceplate I/O in the dual-slot (8HP) version includes additional 2x USB 2.0, 1x COM, 1x KB/MS and Line-in/Line-out on the cPCI-3520D or additional 2x DisplayPorts, 1x COM in RJ-45 connector, 1x KB/MS and 1x additional USB 2.0 port on the cPCI-3520G. Two more dual-slot options are the cPCI-3520L with additional 2x GbE, 1x COM and 2x USB and the cPCI-3520M with one 100-pin high density connector supporting additional 2x DVI-D, 2x USB 2.0, 2x COM, 2x KB/MS and Line-in/Line-out ports.
-
Product
High Voltage 9 Pin D-Type Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 9-pin D-type connector.
-
Product
9025 Rack Mount
-
VPC rack mountable receivers like the 9025 meet the standards which are essential to support advanced mass interconnect requirements. Connector modules can be intermixed to establish custom interfaces which are ideal for functional and system testing applications.
