Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
Preamplifiers
-
Is an electronic amplifier that converts a weak electrical signal into an output signal strong enough to be noise-tolerant and strong enough for further processing, or for sending to a power amplifier and a loudspeaker.
-
Product
Trace Level Chemiluminescence NO-NOy Analyzer
Model T200U NOY
-
Teledyne Advanced Pollution Instrumentation
The Model T200U NOy analyzer has been developed and refined specifically to address the challenges of NOy monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is coupled with a remote NOy converter via umbilical to allow measurements with a lower detectable limit of 50 ppt.The Model T200U NOy analyzer combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer. The remote NOy converter is provided with a stainless steel, NEMA 4X (IP65) enclosure and custom sample umbilical to allow a mounting height of 10 meters. In addition, the converter features a unique purge circuit designed to remove residual calibration gas.
-
Product
Temperature and Humidity Transmitter
T3419
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
CompactPCI
CPCI-ADDA
-
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
-
Product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
Power Line Conditioner
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
Product
Angular Orientation Sensor
WOS-120
-
The Miniature Angular Orientation Sensor system Model WOS-120 contains both a 3-axis fluxgate magnetometer and a 3-axis accelerometer. These sensors are sampled by an internal A to D converter and microprocessor subsystem which outputs 16 bit digital data representing the magnetometer and accelerometer readings. The system can also be configured to transmit the roll, pitch and azimuth orientation angles of the Model WOS-120 system. These angles are calculated before transmission from the accelerometer and magnetometer sensor output data.
-
Product
LXI WTB Adaptor, Terminated
60-982-002
-
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
Product
Keysight 4-Channel D/A Converter with Waveform Memory for 34980A
34951A
Digital / Analog Converter
The Keysight 34951A module for the 34980A Multifunction Switch/Measure Unit has four electronically calibrated analog channels that can output up to +/-16V DC or +/-20mA DC with 16 bits of resolution. Each channel can be updated individually with a 200 kHz update rate. You can use the standard waveforms provided or create your own with over 500,000 points. These points can be dynamically allocated among one or more channels and output as a point-to-point arb.
-
Product
Coaxial Power Detector
-
RF Lambda’s coaxial power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O Module
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - PCIe
Model 78651
-
Model 78651 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A twochannel, high-speed data converter with aprogrammable DDC, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkeysolution.
-
Product
SparkFun BabyBuck Regulator Breakout
3.3V (AP63203)
-
Who doesn't occasionally need power regulation? We certainly do, so we've designed the SparkFun BabyBuck Regulator Breakout to help us with just such a task. Featuring the AP63203 from Diodes Inc, this breakout board takes advantage of a 2A synchronous buck converter that has a wide input voltage range of 3.8V to 32V and fully integrated 125mΩ high-side power MOSFET/68mΩ lowside power MOSFET to provide high-efficiency step-down DC/DC conversion. All of this snuggled up in a low-profile, TSOT26 package that's integrated into a 0.4in by 0.5in board.
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
Product
Conversion Devices and Adapters
-
Conversion devices and adapters fulfill several roles. For example, you can use them to convert an output signal to a signal type that can be measured by a data logger, to adjust resistive bridge measurements, or to build distributed measurement networks.
-
Product
Ultra Low Noise DC Power Supplies
R4G Series
-
R4G series are series regulator system DC power supplies so that enabled setting and reading out more fine output with a 4-digit indicator on furont panel and a high resolution D/A and A/D converter adopted newly.
-
Product
DCDC
DP Series
-
The DP family is an economically priced high performance series of regulated DC/DC converters offering single and dual outputs. Features include MOSFET design operating at a switching frequency of 100Khz, continuous short circuit protection, LC input filter, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. These miniature converters maintain excellent regulation over varying line and load conditions (0.2% for line and 0.5% for load). They are packaged in an IC compatible 24 pin DIP configuration measuring 1.25” x 0.8” x 0.4” high.
-
Product
4-20mA Input A/D Converters
-
Analog Devices range of 4-20mA Input A/D Converters deliver accuracy, robustness and flexibility for Industrial Control applications. As the world’s leading supplier of data converters, Analog Devices is constantly introducing new A/D converters (ADCs) that drive system level architectures. Our portfolio of leading industrial 4-20mA Input A/D Converters offer considerable integration including, sense resistor, signal conditioning circuitry and advanced on-chip diagnostics to maximize performance and provide an integrated system level solution, all based upon robust silicon processes.
-
Product
Pressure Control Setup Using Pid Controller
ULP-26
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Pressure Control Setup comprises of Pressure tank fitted with pressure transmitter to measure the pressure. The pressure is controlled by a pneumatic control valve operated by a I to P converter. The whole system is mounted on a Table top Model with all necessary Piping. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Multiplexed Amplifier-per-Channel Function Card
-
Multiplexed amplifier-per-channel systems have a dedicated pre-amplifier for every channel and a single Analog to Digital Converter, ADC, for the system. Amplified and filtered analog signals are multiplexed to a post-amplifier and then presented to the ADC to be digitized. Significant benefits of the multiplexed amplifier-per-channel system are: Higher Throughput Rates, Improved Filtering, Higher Per Channel Sampling Rate, Sensor Isolation, Improved Channel-To-Channel Isolation
-
Product
8-Input A/D Converter and Counter/Timer Card
AIO8
-
AIO8 is an economical multifunction, moderate-speed, multiplexed analog-to-digital converter card with digital I/O and with counter/timers. It can be used with ISA-bus computers. The card is 7" long and requires one slot in the computer. All external connections are made through a standard 37-pin D-type connector at the rear of the computer.
-
Product
DC-DC Converters
-
Samlex America, Inc Power Supplies
Fully Isolated Regulated DC-DC converters provide stable 12V -12V or 24V-24V regulated output power for situations with an unstable input source.
-
Product
Gain-Compression Measurements
S95086B
-
The S95086B Gain-Compression Measurement (GCA) software provides fast and accurate input power, output power, gain, and phase at the compression point of an amplifier or frequency converter over a specified frequency and power range. With a simple setup, GCA reduces test times through an easy-to-use, fast, and accurate SMART Sweep. GCA also includes a guided calibration that corrects for absolute power levels, frequency response, and mismatch errors.
-
Product
Cylinder type, Near field Antenna Measurement System
anm02
-
As it combines the vertical direction of the probe antenna with the turn of the object antenna, and performs the near field measurement in the shape of a cylinder. The result will be converted to far field. Feature The pattern behind the antenna can be measured by a cylinder scanning. Fast measurement.For example ) Vertical direction 256 point and Rotatory direction 180 point : 30 minutes.
-
Product
DC/DC Converter 2 W
REM2-1509S
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | output 9 V | operates in ambient temperature from -40 to +95 °C
-
Product
I/O's & Converters
-
Rishabh Instruments Pvt. Ltd.,
Module of logic outputs. Control of actuators from monitoring systems or PLC over RS485. 4 relay outputs or 8 OC outputs steered through RS-485/Modbus. Fixing on a TS35 rail. Full galvanic separation between outputs (for relay outputs). Configuration through free LPConfig software.
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
Video Decoders For Automotive
-
Renesas offers a broad portfolio of automotive-grade video decoders that convert analog composite video signals to digital component YCbCr data for applications such as advanced driver assistance systems (ADAS).
-
Product
RFoG 4 Ways or 8 Ways Return Path Optical Receiver
RFoG6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
RFoG6000 series Return Path Receivers are an integral part of two-way RF access networks, converting upstream optical signals into RF signals at the head-end or remote hubs. 4 or 8 independent receivers are packaged in a 1RU 19-inch rack-mounted unit, serving 256 RFoG optical network terminals (ONTs). A low-noise receiver design improves noise performance by 4dB or more over typical return receivers. Low noise enables DOCSIS 3.0. -32dBm receives sensitivity, allow upstream PON-bound design, such as: supporting 32 splitting way in 20km, 64 splitting way in 10km.
-
Product
DC-DC Converters
-
Our proven ability to blend circuit topologies and high-performance components with contemporary construction techniques has led to our premier position in the industry as the largest supplier of DC-DC converters. From standard models to modified products and complete custom designs, Murata''s DC/DC converters can meet the needs for miniaturization, low profile, high efficiency, power-saving, low noise designs for use in industrial and electronic equipment, telecom, medical, automotive, lighting, and more.
-
Product
Audio Video Controllers
-
Most of our cameras can operated remotely. The controllers allow to control the functions of the cameras:– Zoom– Focus– Audio– Pant/Tilt– optionally iris– LANThe controllers convert the optical signal to electrical signalsFor most controllers there is the option to integrate an Ethernet interfaceMost of the controllers can be equipped with an option for shielded intercom. The microphone is either integrated in the housing or a separate microphone can be used.If more than one camera is in use (e.g. one fixed and one mobile camera) multi controllers allow to control several cameras with one device.Up to 4 cameras can be connected to one multi controller. Each camera can be connected to a separate monitor each one monitor can show the selected camera.
