Fuel Injection
-
Product
Fault Injection Module
WF 3154 C-Series
-
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
Product
Mixed Injection System Liquid Vaporizers
MI-1000/MV-1000
-
This mixed injection system can rapidly vaporize a wide variety of liquid sources by using the gas-liquid mixture vaporization method. This method allows for the stable vaporization of high boiling point liquids.
-
Product
Primary & Secondary Current Injection Testing Sets
-
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
Product
Large Current 1000A Primary Current Injection Test Set
TEST-901
-
Beijing GFUVE Electronics Co.,Ltd.
TEST-901 primary current injection test set adopts ARM Chip to control its output process and large capacity of toroidal transformers. It is equipped with LCD display and current meter; it can show primary current value, second current value, turn ratio and the action time. Packing is used as aluminum alloy body with PC panel. TEST-901 is mainly applied to CT turn ratio testing in the power system and contact resistance test which need large current.
-
Product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
-
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
Product
Secondary Injection Test Set
PTE-100-C Plus
-
In the Pro version this voltage source incorporates a dedicated LCD display and its own BUS-PTE connection that make the operation easier and enable it to be used also with other sets in the PTE range.
-
Product
MASTER FUEL PRESSURE TEST SET
FPT5000
-
*Quickly and easily diagnose fuel-related issues on most major gasoline engine platforms, including domestic and foreign vehicles*In-line adapter configuration allows for easier connection to the fuel system as well as the ability to isolate the supply and return lines independently without disconnecting the adapters from the engine*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary
-
Product
PXI Fault Insertion (Fault Injection) Modules
-
PXI Fault Insertion Units (FIU), also known as Fault Injection switch products, are designed specifically for safety-critical applications where the response of a control system is required to be evaluated when sensor connections behave in unexpected ways. These modules are scalable solutions that can be used to switch signals between simulations and real-life devices in a multitude of hardware-in-the-loop (HIL) simulation and test systems. The fault insertion unit can significantly simplify and accelerate the testing, diagnosis and integration work in HIL applications.
-
Product
Universal Primary Injection Test Set for Substation Assets
CPC 100
-
The patented CPC 100 primary injection test system replaces several individual testing devices. This reduces the costs for training and transport, and cuts down testing time.
-
Product
Injection Transformer
J2101A
-
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
Product
Fuel Hose Assembly Tester - USAF
9201
-
The purpose of this equipment is to provide a source of high pressure fluid for proof testing of fuel hoses after assembly or on a periodic schedule as required by specification.
-
Product
Hydrogen Fuel Cell
-
Honeywell Aerospace Technologies
Honeywell has a decades-long history of innovation in power generation for all kinds of aerospace and defense applications, which was further strengthened by the 2020 acquisition of Ballard Unmanned Systems, a global leader in fuel cell technologies for unmanned aerial vehicles (UAVs).
-
Product
SparkFun LiPo Fuel Gauge
-
LiPo batteries are a great way to power your projects. They're small, lightweight, and pack a pretty good punch for their size. Unfortunately, even the best batteries eventually run low on power and when they do it's often unexpected (and at the worst time). Don't be caught by surprise next time your board suddenly powers-down! The SparkFun LiPo Fuel Gauge connects your battery to your project and uses a sophisticated algorithm to detect relative state of charge and direct A/D measurement of battery voltage. In other words, it tells your microcontroller how much 'fuel' is left in the tank. The LiPo Fuel Gauge communicates with your project over I2C and an alert pin also tells you when the charge has dropped below a certain percentage.
-
Product
Primary Current Injection Testers
-
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
Product
Primary Injection Testing
-
For primary injection testings, PONOVO has been providing users, various testing equipment, including CT/PT test set, Single phase universal test test upto 250A and 1000A, etc. CT/PT tester could be used for testing all kinds of CT testing, with additional PT testing functions.
-
Product
Electronic Fuel Quantity Indicator
-
Proportional to the amount of fuel in the tank, thereby visibly indicating remaining fuel quantity to the pilot.
-
Product
Fuel Cell Test Systems
-
Fuel Cell Test System is a complete test station for operation and measurement of PEM/DMFC fuel cells.
-
Product
Injection Transformer
J2100A
-
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
Product
Primary Injection Test Set
T1000
-
T1000 primary injection test set is the model featured with light weight and 2 minutes continuous output time at 1000Aac.
-
Product
Direct Liquid Injection System
VC Series
-
The VC Series is able to rapidly vaporize pure water or other liquid sources without carrier gas, which enables you to construct a more compact vaporization system.
-
Product
Fuel Cell Test Software
-
Exceptional functionality with a user-friendly graphical interface- Enhanced with our proprietary automation language, Emerald Software - Comprehensively manages the full range of FCATS fuel cell test system parameters- Simple user-friendly interface permits even novices to begin testing in minutes
-
Product
Secondary Injection Test Set
PTE-100-C Pro
-
The values which are presented in the LCD display are highly accurate, easy to read, and independent of the injection made by the PTE-100-C base unit.The display shows continuously the phase difference between the voltage and the current injected, and can be adjusted during the test with an accuracy of 0.1º. This facilitates the test for directional relays or reclosers and synchronizing relays, etc.
-
Product
Primary Injection Test Systems
-
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Product
Multi-Stage Injection Analyzer
FJ-8000 series
-
Common rail method already is commonly known as an injection system of diesel engine now. That system enables multi-stage fuel injection by offering high injection pressure in various driving situation. Adopting the common rail system helps improving fuel consumption, reducing noise and vibration, because the system can make the fuel approximate complete combustion which suppresses PM and NOx generation. FJ-8000 series is the multi-stage injection analyzer that supports more accurate injection by measuring injection quantity, injection rate, injection timing, and injection period by multi-stage injection of common rail system in the environment that is near to an actual vehicle environment.
-
Product
Primary Injection Test Systems
-
Weshine Electric Manufacturing Co., Ltd
1.DC display primary current, secondary current test value, easy to observe and record the experiment..2.High measuring accuracy: 0.5 level.3.Small size light weight easy to carry.
-
Product
Track (Oval)type ZCT Sensor／Through Hole type ZCT/CT Sensor／Injection CT Sensor
Track Type ZCT Sensor
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accurate track(Oval) type ZCT sensor*Through hole type
-
Product
Single Phase DC Injection Set Kit
PDC120A/PDC200A
-
PDC120A/PDC200A Single Phase DC current injection set kit is portable test set which could generate DC current for the various testings in railway transportation, HVDC converting stations, etc.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Current Injection
-
K&S Engineering and Scientific Ltd
The outputs are continuously variable from zero and are all isolated. The current outputs can be used at twice their continuous rated current on a 25% duty cycle with a maximum ON time of 5 minutes.
-
Product
Fuel Cell Test Stations
-
The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software.
