Electron
-
Product
LWIR Micro Thermal Camera Module
Lepton®
-
The FLIR Lepton® is a radiometric-capable LWIR OEM camera solution that is smaller than a dime, fits inside a smartphone, and is one tenth the cost of traditional IR cameras. Using focal plane arrays of either 160x120 or 80x60 active pixels, Lepton easily integrates into native mobile-devices and other electronics as an IR sensor or thermal imager. The radiometric Lepton captures accurate, calibrated, and noncontact temperature data in every pixel of each image.
-
Product
Mechanical Test Service
-
The mechanical properties of an electronic system enclosure have to be stressed in order to determine the robustness of the total system. The multiple electrical interconnections have our special attention.
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
Electronic Ballast Tester
WT4000
-
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
Product
Counterfeit Defect Coverage Tool
-
The SAE Counterfeit Defect Coverage Tool is a dynamic, web-based application that supplements SAE Standard AS6171 authored by the SAE G-19A Test Laboratory Standards Development Committee. It provides potential test sequences for the identification of counterfeit electrical, electronic, and electromechanical (EEE) parts along a range of risk levels and EEE part types. Allowing users to compare alternative test sequences as a function of resources needed to implement those tests, the SAE CDC Tool is appropriate for those ordering counterfeit detection tests as well as those performing the tests.
-
Product
Varactor Tuning Diodes
-
Macom Technology Solutions Holdings Inc.
MACOM’s GaAs and Silicon varactor tuning diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for high Q filter and VCO electronic tuning circuits and are available in die form, flip chip, plastic and ceramic packaging. These GaAs diodes boast a constant gamma series for higher frequency and high Q applications and silicon abrupt and hyper abrupt series in plastic packaging are suitable for high volume surface mount applications.
-
Product
8-Slot BRIC, 1024x4, 1 Pole, PXI Matrix (8 Sub-cards)
40-559-801-1024x4
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
A/D, Digitizers, Transient Recorders Basics
-
A digitizer is an electronic acquisition device that acquires analog waveforms, processes them through analog-to-digital converters (ADC’s) and sends the digitized sample to a buffer, which allows them to be saved before being processed by a computer. Waveform digitizers are plug-in cards for PCs or industrial PCs that are used to measure continuous voltage signals as well as fast signal changes like voltage transients. Therefore they're also called transient recorder.
-
Product
Fluxmeter
B3
-
Electronic integrator of high sensitivity and extremely low drift. Equipped with RS 232 interface, maximum minimum store and comparator. 4 measurement ranges. Constants of measuring ranging from 10E-7 Vs/digit to 10E-4 Vs/digit.
-
Product
Three Phase Electrical Power Calibrator
6003A
-
The Fluke Calibration 6003A Three Phase Electrical Power Calibrator is the most cost-effective way to get the superior accuracy and performance of three independent phases in one instrument. It is an ideal solution for calibration laboratories, electronics manufacturers, electric utility meter shops, and other organizations that manufacture and maintain energy meters, power quality analyzers, and similar tools.
-
Product
Dissolved Gas Systems
-
Dissolved gas in deionized water has been widely adopted in manufacturing processes in Electronics, Semiconductors, Flat Panel Displays and Solar applications. These wet techniques increase manufacturing productivity in particle lift-off and wet clean operations. Dissolved gases such as Ammonia, Carbon Dioxide and Ozone are environmentally friendly alternatives to heavy chemicals like sulfuric acid and peroxide acid solutions. MKS offers a large product line of Dissolved Gas systems that improve wet cleaning operations.
-
Product
EMI Test Receiver
SER
-
Saluki SER series EMI receivers comply with CISPR 16-1-1 standard, integrated CISPR-AVG, CISPR-RMS, QPK detectors, and electromagnetic interference measurement. According to CISPR, EN, FCC and MIL standards, which is suitable for EMI testing in home appliances, lighting, automotive electronics, medical, and other industries. Combined with ETR PC measurement software and a wealth of test options, accurate automated testing is possible. The whole system is equipped with a spectrum analysis module and a tracking signal generator to meet the testing needs of users in different fields.
-
Product
Cable Harness EM Solver
MHARNESS
-
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
Product
Hardware-in-the-Loop Test Systems
HIL
-
Our early development efforts and NI VeriStand expertise uniquely qualify us to maximize the benefits of and provide top-notch integration services for this software platform. Wineman Technology offers powerful and flexible MIL and HIL testing solutions, such as: Full range of MIL and HIL test systems. Software for testing. Software for simulating electronic control modules. Fault insertion unit (FIU)..
-
Product
SINGLE ENERGY IMPACT HAMMERS
-
Shenzhen Chuangxin Instruments Co., Ltd.
It’s used to test the mechanical integrity of product enclosures and check the durability of enclosures for electrical appliances of other electrical appliances and other electronic products. If damage occurs from the Impact Hammer test, accessibility probes can be used to measure the extent or severity of the damage. The Impact Hammer simulates the mechanical impact to which electrical equipment maybe subjected.
-
Product
PXI 8-slot BRIC Matrix, 320x16, 1 pole (10 Sub-cards)
40-558-801-320x16
Matrix Switch Module
The 40-558-801-320x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
SolderStar Solutions
-
Solderstar provides a complete solution for soldering process control within the Electronics Manufacturing industry.
-
Product
Satellite Simulator
HSDS
-
Hollis Electronics Company LLC
Hollis Electronics HSDS-140 and HSDS-70 satellite simulators are a high technology, low-cost solution for Earth Station to Satellite Link Simulation. Both satellite simulators offer the same features and differ only in the frequency and bandwidth supported.
-
Product
LCZ LCR Meter
SS1063
-
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor,cable,wire,etc.
-
Product
ATCA 5U 14 Slot dual star
109ATCA514-300XR
-
The Elma Electronic 5U ATCA Dual Star backplanes feature pluggability and redundancy "everywhere". There are pluggable connectors for fan trays, shelf managers, and power entry modules.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
Heated Dew Point System
DPS3
-
Model DPS3 is a heated dew point hygrometer that can measure dew points up to 95 °C (203°F) and as low as -35 °C (-31°F). This integrated system includes a microprocessor based electronics, a chilled mirror dew point sensor, a sample flow meter/valve, assorted tubing and fittings all contained in a heated, temperature controlled NEMA-4 enclosure.
-
Product
Electronic Bypass Flow Meters
4912
-
Parker Conflow’s Code 4912 is an Intrinsically Safe electronic bypass flow meter that is designed for high flow, high pressure situations on mining roof support systems.
-
Product
Power Analyzer
PW3390
-
The PW3390 delivers 4 input channels and ±0.04% basic accuracy for power - the top instrument in its class. Achieve more precise measurements of the power and efficiency of high efficiency equipment used in power electronics. Further, a 200 kHz measurement band and flat amplitude and phase characteristics up to high frequencies enable the precise measurement of power at top frequency levels and low power factor.
-
Product
FastCamera
FC1700
-
The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
Product
Breakout Box and Data Logger
1U643-001
-
The 1U634 Breakout Box and Data Logger was developed for the Cessna Excel to serve as the main diagnostics tool for the aircraft?? electronic modules. It allows access to the module pins, and its internal microcomputer digitizes the signals and transmits them to a PC-compatible computer. Advanced software in the computer displays pin voltages either in numerical or graphical form. Data files can be recorded on disk, and played back at a later time for detailed analysis.
-
Product
Fracture Mechanics Clip-On Gages
Model 3541
-
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
CAN Interface
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
-
Product
Joist And Stud Detector With Bubble Level
6342
-
Peaceful Thriving Enterprise Co Ltd
Electronically locates hidden wood & metal stud.
-
Product
Telemetry Antennas
-
Communications & Power Industries
CPI SAT is a multinational manufacturer of high-performance, highly engineered antenna systems used for critical satellite communications, telemetry, tracking and control (TT&C), general telemetry, earth observation (EO), radar, electronic warfare, search and rescue and other specialty applications. Offering advanced antenna systems for land, air and sea, with a full range of solutions and capabilities to meet any military requirement, and its Orbital Systems operations design and manufacture antenna systems that meet the high performance, accuracy, and high reliability needs of demanding satellite tracking applications and mission-critical uplink and downlink applications.
