Distribution Amplifiers
amplify each output from input's split.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Video Distribution Amplifiers
-
Product
LINEAR AMPLIFIERS
-
These amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance and fast response. The output is linear from DC up to megahertz range.
-
Product
Amplifier Built-in Ultra-compact Laser Sensor
EX-L200
-
Panasonic Industrial Devices Sales Company of America
The EX-L200, the one of the world’s smallest Laser Sensors with a built-in amplifier, is designed to detect minute objects with utmost accuracy. Despite its miniature size, the Thru-Beam Type (EX-L211) can detect minute objects with a diameter of just 0.3mm, and the Spot Reflective Type (EX-L221) can even detect gold wire whose diameter is a mere 0.01mm. To facilitate solving application tasks, these sensors come equipped with a Potentiometer and two indicator LEDs. For the Thru-Beam Type, reflective material on the receiver allows users to visualize the laser beam, easing beam-axis alignment.
-
Product
40~860 MHz Trunk Hybrid Amplifier
AS 1616
-
Hybrid Amplifiers used in Trunk and branch lines specially designed to serve the needs of cable systems with very Long Trunk Cables. They are in Aluminium Housing providing maximum heat dissipation and have RFI Shielding. They incorporate superior quality Hybrid IC Module to obtain excellent features.- Frequency Range: 40 ~ 860 MHz- Mains cum Power Pass- Output Level: 102 dBµV- Level Flatness: ±0.75 dB- 32 dB Gain (40 dB Optional)- Optimum for Trunk Distribution- Superior Quality Hybrid IC Module- Hybrid IC Protected- Voltage Selection LED - for Easy Selection
-
Product
GaN Amplifiers
SBP-3233831838-KFKF-E1-HR
-
Model SBP-3233831838-KFKF-E1-HR is a power amplifier with a typical small signal gain of 18 dB and a nominal Psat of +38 dBm across the frequency range of 32 to 38 GHz. The DC power requirement for the amplifier is +30 VDC/2 A. The mechanical configuration is an inline structure with K(F) connector as its input port and output port. Other port configurations, such as K connectors and WR-28 waveguides for either the input or output, are also available under different model numbers.
-
Product
Utilization Planning, Radio Network Configuration, Data Distribution
SOVERON
-
R&S®SOVERON® management software supports centralized network management, where a central organizational unit performs complete mission planning as well as decentralized management, where the various configuration steps are made at different military hierarchy levels.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
Erbium Doped Amplifier
CATV
-
Amonics CATY Rackmount EDFA area made with high power pump laser and stability pump combiners, robust in high power boosting. The result are EDFAs that possess high output power, high gain with very low noise, and are ideal for CATV applications. The turnkey microprocessor controlled rackmount EDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
Portable Power Amplifier
PAV250Bip
-
PAV250Bip is the portable OPAL-RT used amplifier model, which is specially designed for R&D of power system simulation. It is designed with linear type amplifier so that it is with precise accuracy, which could be adapted to various capacitive and inductive load.
-
Product
RF High Power Amplifier Modules
-
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
Product
RF Amplifier Modules
-
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
Product
Thermocouple Interface Amplifiers
-
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
Product
GaN 100W Power Amplifiers
PE15A5033F
-
The PE15A5033F is a 100 W high gain Class A/AB Coaxial Linear Power Amplifier operating in the 0.7 to 2.7 GHz frequency range. The amplifier offers 100 Watts typical saturated power and 45 dB minimum small signal gain with 1.5 dB typical gain flatness @ Psat. The amplifier requires typically a +30V DC power supply. The SMA connectorized module is unconditionally stable and operates over the temperature range of 0C and +50C. The unit comes with a Heatsink and Fan.
-
Product
Extensible & Modular Broadband System on Flexible, Distributed Microservice Architecture
Connect Modular Broadband
-
Connect Modular Broadband is an extensible and modular broadband system built on a highly flexible, distributed microservice architecture. Leverage the benefits of disaggregation underpinned with open network hardware and unlock unprecedented levels of automation.
-
Product
Solid State Power Amplifiers
SSPAs
-
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
Product
Low Phase Noise Amplifier
-
RF Lambda’s lower phase noise amplifier offerings include special power supply conditioning and utilize technology to reduce the phase noise addition from amplifying the signal. Hermetically sealed options are available upon request.
-
Product
Dual Channel High Voltage Linear Amplifier
F10AD
-
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-819
-
The SCS-818 and SCS-819 amplifier/filter module provides eight 4-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-818) and 0.5Hz to 70kHz(SCS-819). Each of the SCS-818/SCS-819's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
Analysis Tool for ECU Networks and Distributed Systems
CANape
-
The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware, CANape can store multiple gigabytes of data per second. Calibration data management and convenient measurement data evaluation including data management as well as reporting make CANape a complete tool for ECU calibration. Of course, CANape also provides access to bus data, diagnostic data and analog measurement data.
-
Product
Single-Ended to Differential Amplifiers
-
Analog Devices has developed a broad portfolio of single-ended to differential amplifiers that help designers meet their high performance requirements. ADI single-ended to differential amplifiers enable the processing of both single-ended inputs to complementary differential outputs or differential inputs to differential outputs. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single-ended output.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800E (5RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800E (5RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Precision Op Amplifiers (Vos <1mV & TCVos<2uV/C)
-
Analog Devices' broad range of precision amplifiers provides industry-leading support to designers in need of traditional trimmed and zero-drift amplifier technology. Our precision amplifier family helps preserve the accuracy of dc information in an incoming signal with low offset voltage (VOS < 1 mV) and low temperature drift characteristics (TCVOS < 2 V/C).
-
Product
DALI Distribution And Commissioning
UBi
-
Every UBi can create up to 6 branches of a DALI line. Simply put a DALI line into one of the 2-way pluggable terminals, and then use any combination of the 5 remaining terminal pairs to route your cable anyway you like. Or, if you want the UBi to be a power supply, simply power a UBi Power with 24VDC and it will power your DALI line with 21.9VDC 245mA and still give you 5 DALI connections – one for your DALI controller and four to branch however you like.
-
Product
Power Amplifiers
-
Precision Test makes two power amplifiers for use with our FSG series of hand held signal generators.
-
Product
Amplifiers
-
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
Product
RF Benchtop / EMC Amplifier
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
-
Product
DVB-T Amplifier Module
-
The COMM-connect DVB-T Amplifier Module is a very versatile module, for use in multiple applications, including driving High Power amplifiers or stand alone Gap-filler. The amplifier covers both VHF & UHF bands, and can be combined with several COMM-connect filter options.
-
Product
Amplifiers & Signal Processors
-
Power for Core Technology Group Signal Chain ProductsFlexible bi-polar voltage converter using low cost connectorsDriving multiple devicesIndustrial +/- 10 volt power source
-
Product
Modal Exciters & Amplifiers
-
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Product
SparkFun Qwiic Thermocouple Amplifier
MCP9600 (Screw Terminals)
-
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
Product
Power Divider Combiner, 2 Way, SMA RF Splitter for Distributed Antenna Systems (DAS)
PD2120
-
INSTOCK Wireless Components, Inc
Ideal for DAS (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy SMA Female (Jack) 50 Ohm
