-
Product
Interference Source, 32 GHz
M8054A
Interference Generator Module
32 GHz interference source blade for the M8040A BERT.
-
Product
Interference Locating System
SeeWave®
-
Interference impacts wireless network coverage and quality of service, but hunting interference in the field can be expensive and time-consuming. PCTEL’s SeeWave® interference locating system enables a single user to accurately detect the interfering frequency and locate its exact source.
-
Product
Interference Modeling And Simulation
-
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
Product
Interference Detection And Mitigation
-
Now more than ever, it’s critical to protect military systems from the threat of GNSSGlobal navigation satellite system (GNSS): A general term describing any satellite constellation that provides positioning, navigation, and timing (PNT) services on a global or regional basis. See also GPSGlobal Positioning System is a navigation satellite system. See also signal jamming and spoofing by using anti-jamming GPS and spoofing detection solutions.
-
Product
Spectrum Monitoring and Interference Systems
-
Automate wide area, close-proximity signal monitoring, interference detection, identification, location, reportingIncrease flexibility; set up rugged, portable-RF sensors in fixed, temporary or mobile platforms in any environment for extended periods of timeRemotely deploy a single sensor or a network of sensors synchronously country or city-wide, or in a roomCustomize for your application with software for spectrum monitoring, emitter location, signal intercept, capture/analysis
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Interference Simulation System
GSS7765
-
Combined with Spirent’s powerful GSS7000 or GSS9000 Series simulators, the GSS7765 interference generator creates the ultimate tool for testing against external jamming and unintentional interference. The GSS7765 enables you to create and generate custom waveforms, helping you to defend your systems against real-world threats.
-
Product
Spectrum Monitoring and Interference Detection Software
-
Supports multiple users; Compartmentalization between profiles; Allows real-time monitoring and generates SMTP alarm traps; Displays a large number of carriers (100+) Numerous RF calculations and monitoring settings; Waterfall Display; Spectrogram Display; OCBW, ACPR, 3dB Bandwidth; Min/Max, Channel Power; Up Time Report; All Major Browsers Supported
-
Product
Noise & Interference Generator
GPS7500
-
The programmable GPS7500 Noise & Interference Generator is capable of generating up to a 40 MHz wide noise or interference band for GPS receiver susceptibility testing.
-
-
Product
Metallic Probe Inductive Proximity Sensor
-
Shanghai Pubang Sensor Co.,Ltd.
1. All-in-one stainless steel housing design, strong anti-shock function2. Magnetic field interference, high switching frequency, wide temperature range3. Protection class IP67 (IEC)
-
Product
Customized Multibeam Echosounder Solutions
-
Our proven approach ensures that our customers will benefit from a turn-key survey solution. This can also include an acoustic synchronization unit in order to avoid acoustical interference of different hydro-acoustic on-board sensors or data management software providing an overview of the data being collected by the scientific instrumentation.
-
Product
EMI Receiver
KH3939
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Monics SatGuard
-
Kratos Defense & Security Solutions, Inc.
SatGuard can help resolve in minutes, revenue loss problems that have lasted weeks, months or longer. The VSAT monitoring and mitigation product from Kratos classifies VSAT networks and identifies the specific IDs of the terminals causing interference to much more quickly resolve issues.
-
Product
EMC/EMI
-
American Environments Co., Inc.
ElectroMagnetic Compatibility/ElectroMagnetic Interference
-
Product
EMC Testing Inductors
-
Electromagnetic Compatibility (EMC) testing is a somewhat unique discipline within the world of electrical product development and analysis. Electromagnetic Compatibility (EMC) testing is primarily concerned with understanding and mitigating the affects of Electromagnetic Interference (EMI).
-
Product
Modulation Distortion Up To 8.5 GHz
S930700B
-
S930700B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 8.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930700B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
L Series Receiver
LR
-
Excellent performance in a small package for ENG and DSLR video production is the purpose and intent of the LR receiver design. Tracking front-end filters block interference from high powered RF signals on nearby channels to preserve the extended operating range. RF spectrum scanning displays accurate results on the LCD to make finding clear spectrum quick and easy.
-
Product
Ring Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
Product
Basic Contact Probes H772LI-0.1
1018289
-
Introducing the H772LI-0.1 Basic Contact Probes, designed for precision and reliability in various electrical applications. With a pitch of just 100 mil (2.54 mm), these probes ensure optimal connectivity for your devices. The total length of the probe is 30.50 mm, featuring a sleek outer diameter of 2.00 mm, which allows for easy fitting and reduced interference. The press ring diameter of 2.04 mm and collar height of 0.20 mm contribute to secure connections, maintaining a robust interface across different environments.
-
Product
Automatic Capacitance and Tan Delta Bridge
-
*Automatic Microprocessor controlled Guarded Bridge Circuit.*Suitable for testing at voltages up to 500kV.*Can be used to measure both Grounded and Un-Grounded Specimens.*Automatic guard circuit for three-terminal measurement.*Interface measurement and automatic interference suppression circuitry.*Optional range Extension Transformer for large capacitance values.*Test data storage facility.*RS-232 computer interface and USB printer interface.*Window Interface Software for data transfer.
-
Product
Predictive Emission Monitoring Systems
PEMS
-
Predictive Emission Monitoring Systems are software-based solutions able to deliver reliable real-time emission estimations exploiting advanced mathematical or statistical models. PEMS provide accurate emission monitoring, drastically reducing the capital investment and ongoing operating costs due to maintenance activities and spare parts, minimizing the interferences with plant operations. PEMS allows plant owners and operators a better control on costs, neglecting unexpected costs due to unpredicted issues in the conventional hardware analyzers.
-
Product
Wavefront Modeling And Simulation
-
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
Product
Signal Analysis
Synchronous Accumulation (Order Analysis)
-
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
Product
4-Port Isolated RS-232/422/485 With IRIG B Card
ECU-P1624D
-
industrial communication module designed for high-reliability, time-synchronized serial data transmission. It supports four software-configurable RS-232/422/485 ports, often including isolation for interference protection, alongside an IRIG-B time synchronization input, commonly used in substation automation.
-
Product
RS232 / RS485 / RS422 / TTL Serial Converters
-
Rated to perform at temperatures between -40°F and 185°F (-40°C and 85°C), our rugged industrial-grade RS232 / RS485 / RS422 / TTL serial converters are almost indestructible. These industrial-grade serial converter products support multi-drop RS485 / RS422 networks and come with 600W surge protection, 15KV ESD protection, selectable end-of-line terminators, and optional 2500V opto-isolation circuitry, which ensure crisp data signals without interference for all types of installations.
-
Product
Test tools
-
Try our low-cost RF sniffers for fast and easy troubleshooting of unwanted interference caused by electromagnetic radiation sources in your local environment.
-
Product
LISN Line Impedance Stabilisation Networks / AMN Artificial Mains Network
-
A LISN Line Impedance Stabilization Networks / AMN Artificial Mains Network: *supplies the neccessary mains voltage (AC or DC) and current for the Equipment under Test (EuT).*couples interference voltage generated by the EuT and supplies it to the receiver.*provides well defined RF-impedance to the Equipment under Test (EuT)*keeps away unwanted disturbance coming from mains (filter)*protects the mains from unwanted disturbance voltage generated by the EuT
