Counting
-
Product
LXI WTB Adaptor, Thru line
60-982-001
-
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
Product
Quadrupole Mass Spectrometer for Residual Gas Analysis
RGA Series
-
Systems for the examination of components present in a vessel or evolved from a process. HALO RGA – for residual gas analysis. 3F Series RGA – triple filter mass spectrometers for analytical applications. 3F-PIC – pulse ion counting detection for fast event studies. Measures the concentration of gases and vapours in real time.
-
Product
cDAQ-9188 , 8‑Slot, Ethernet CompactDAQ Chassis
782824-01
-
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Wide Angle Scale Instrument
LS-110 Watt
-
Standard Electric Works Co., Ltd
LS-110 DUAL Wide Angle Scale meters are combination Digital/Analog indicating instruments. They can be configured to accept ACV, ACA, DCV or DCA, Hz input. Both the digital and analog displays can be modified to represent virtually any scaling or engineering units as required. It utilizes a moving coil type element , 3-1/2 digit display for indication (+ or - 1999 counts).
-
Product
Automated DC Parametric Curve Tracer
MultiTrace
-
MultiTrace curve tracer is a mid-sized benchtop model supporting pin counts from 216-625 pins and includes the PGA-625 fixture as a standard interface. MultiTrace supports a wide range of test applications: Failure analysis, Reliability testing, Counterfeit device analysis, Nondestructive electrical counterfeit test, Opens, shorts leakage testing (OSL), Post decap electrical inspection, Optical fault localization, ESD testing, Latch-up testing, Supply current measurements, and more!
-
Product
Two-Way Optical Loss Test set
KI23422OLV-INGAAS
-
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber at 1310 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use.
-
Product
PXI High Density MUX BRIC, 6-Chan, 160-Pole
40-570-016
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Photon Doppler Velocimeter - MATRIQ
-
The Quantifi Photonics Doppler instrument combines the key optical components for Photonic Doppler Velocimetry (PDV) measurements in a compact instrument to enable streamlined high-channel count PDV test setups.
-
Product
Milli Ohm Meters
-
Teledyne Test Tools series of D.C. Milli-Ohm meters offer two models T3MIL50 and T3MIL50X, which features a 3.5-inch TFT display with a measurement accuracy of 0.05%, maximum 50,000 count measurement display and sampling rate of 60 readings per second. The T3MIL series also provides four wire measurement as well as temperature measurement and temperature compensation functions to meet the requirements of low resistance measurement applications.
-
Product
Digital Multimeter
6410 DM
-
Standard Electric Works Co., Ltd
● 3000 counts with a maximum display of 2999.● Angled display design helps the user to identify the reading of value easier.● Auto scanning function for AC/DC voltage, and current.● Auto ranging.● Range change function.● Continuity check.● Diode & Capacitance measurement.● Data hold function.● Low battery indication.● Over range indication.● Fuse protection.● Special hook design used to hang the meter for ease of use.
-
Product
Full Wafer Test System
FOX-1P
-
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
Product
Advanced Multimeter
7117
-
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy and stable hand held 6000 counts multi-meter; with special designed IC to support true RMS measurement. It performs measurements of DC voltage/current, true RMS AC voltage/current, resistance, capacitance, frequency, diode, continuity, temperature and non-contact voltage sensing.
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782258-01
-
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI-2598, 26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module
778572-98
-
26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module—The PXI‑2598 is a general-purpose switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2598 is also well suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking to predict relay lifetime and reduce unexpected system downtime.
-
Product
Rolling Seal 4 Optical Connector
RS4
-
- GAF/ELI enhances mating efficiency and eliminates potential for shell damage while offering positive latch indication.- Longer, contoured cable end lead-in bushing enhances fine alignment of connector halves during the mating sequence.- Reduced channel count to align with more efficient field architectures.
-
Product
PXI 3A Power MUX BRIC, 8-Channel, 6-Pole
40-571-401
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Autoranging Digital Multimeter
HH2205F
-
High Accuracy (Basic Accuracy 0.5%). 3-3/4 Jumbo LCD display 4000 count with symbolic signs. Auto Ranging High Voltage test up to 1000V DC and 750V TRMS AC. Higher Current test up to 20A AC/DC. Diode and Continuity check. Measure Resistance up to 40MΩ. Measure Temperature up to 760oC or 1400oF
-
Product
Insulation Resistance Testers
-
Shanghai Beha Electronics Co., Ltd.
*This is a variable high voltage insulation tester from 500V to 15kV in 500V steps.*The is menu driven and uses Dynamic Current Auto ranging technology.*It has a Bar-Graph which displays the voltage stressing the insulation while the test is in progress and the voltage decay during the automatic discharge of the tested circuit.*The top line of the display shows the elapsed time at the start of the test. Digital readout of the total time will remain displayed even after testing has ceased.*A 4-digit display (2000 counts) is showing the actual insulation resistance.*This instrument displays a voltage warning and sounds when AC or DC is present before injecting the test voltage.
-
Product
Saluki SFS-2000H Fusion Splicer (6 motors)
-
SFS-2000H series is the core-to-core alignment (6 motors) fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, and more intelligent. The rich functionality and ultra-low splice loss make the splicer adaptive to fiber splicing in various environments.* Core to core alignment (6 motors)* 7s fast splicing, 14s highly efficient heating* 320/200 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups and 100 images of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 300 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
Product
Accelerometer & Platform Test Bench
mS 1115
-
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
Product
Appliance/Tool Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• Lowest Board Count In Industry• No Proprietary Circuit Boards• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
Product
Handheld Digital Multimeter, 4 digit, Water and Dust Resistant
U1271A
-
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.7% for ACV accuracy)Intelligent features to improve productivity and safety (selectable Low Pass Filter LPF and quick signal type identification Qik-V)Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 200) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
Product
PXI/PXIe High Voltage Multiplexer, Single 48-Channel, 2-Pole
42-321-129-HI
-
The 40-321-129-HI (PXI) and 42-321-129-HI (PXIe) are single 48-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
-
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Counters & Frequency
-
NLS panel mount digital counters, frequency meters, and interval timers are available in four case sizes and feature a wide range of functions. These versatile, rugged, and low cost meters find many applications. Features in various meters include highly accurate crystal time base circuitry, counts of up to one million per second, frequencies to 60 MHz, battery back-up and a presettable decimal point. Multiplexed BCD outputs are also available for some meters.
-
Product
Precision Dials
HROII-PD and HROII-PDA
-
National RF’s HROII-PD and PDA precision dials were inspired by the earlier National Radio Company’s famous HRO series of communications receivers. This earlier equipment incorporated a ten turn dial with a rotating number plate on the inside. Every 72 degrees of rotation, a new number appears in a rectangular cutout in the dial skirt. The numbers count from 0 to 500 in decade intervals. The HROII-PD and PDA duplicate this counting action but in a smaller diameter assembly than the earlier dial.
-
Product
Impact Testing Machine (Izod & Charpy)
-
Suitable for Charpy & Izod Impact tests on different materials. It is based on Pendulum principle.Rigid designs of instrument frame & other parts assure minimum energy absorption during fracture which results in improved test accuracies.The highly strained & wearing parts like support blocks & strikers are of special alloy steels duly heat treated.Direct indication of Impact energy absorbed by sample on large dial -Safety guard for the user is provided.Initial potential energy for Charpy is 300 Joules & for Izod is 170 Joules with a Least Count of 2 Joules (for Analogue models) & resolution of 0.5 Joules (for Digital Model).Drop Angle of Pendulum for Charpy is 140° & for Izod is 90°.ASTM Impact Testing machine is also provided, which conforms to E-23 ASTM standard.Gauges, Tongs, Sub-zero bath, Templates, U & V Notch milling cutters are available with it (Optional).
-
Product
Conventional Meters
-
Shenzhen Star Instrument Co., Ltd.
Conventional Meters always counts energy as forward energy, irrespective of the real energy direction. It detects cover opening and measures energy by multi tariffs even with the N line fail.
-
Product
93 Ohm Coax Cable
RG62A/U
-
RG62A/U part number from Pasternack is a RG62 coax cable that is flexible. Pasternack RG62 flexible coax cable is 93 Ohm and has a PE (AS) dielectric. Our RG62 coax is constructed with a 0.239 jacket made of PVC. RG62 coax has a shield count of 1, a RF shielding of 45 dB and the maximum frequency for this Pasternack cable is 1 GHz. RG62 coax cable has an attenuation at 1 GHz of 8.7 dB and a maximum power of 77 watts at 1 GHz.
-
Product
Autoranging Digital Multimeter w/Bargraph
HH2209
-
High Accuracy (Basic Accuracy 1.0%)Jumbo LCD display 3260 count, 21mm figure heigh with BaragraphAuto Ranging or Manual Ranging at your choiceHigher Voltage test up to AC 750V and DC 1000VHigher Current test up to 20AResistance test up to 30MΩTemperature test range from -4oF or 1832oFWide Frequency test range up to 300kHzDiode test, audible continuity check and Transistor testLow Battery Indication
