Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
product
Universal SOIC ZIF (Zero-Insertion-Force) Test Socket
Series 547
Universal SOIC Zero Insertion Force Test Socket. Devices with up to 44 pins can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Accepts SOIC gull-wing and J-lead devices, up to 44 pins on .050 [1.27] lead pitch, body widths from .150 to .600 [3.81 to 15.24].
-
product
Force & Strain Measurement
Load cells, tank weighing devices, balances, scales, force gauges, torque sensors and strain gauges including diaphragm, dual parallel, linear, rosette, T-rosette, and torsion and shear types.
-
product
Bond Force Measurement And Calibration Systems
BFS-20
Based on its design and easy handling it can be used also on other brands to measure the bond force.
-
product
3-Component Quartz Force Links
261 Series
Three-component force links eliminate the preload requirement of 3-component quartz force ring sensors, and offers a convenient, 4-screw hole mounting plate on each side end the sensor. Quartz 3-component force links are constructed by installing a 3-component force ring sensor, under preload, between two mounting plates.
-
product
Verification Of Maximum Withdrawal Force Test Apparatus
IEC60884 FIG 18
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG 18 verification of maximum withdrawal force test apparatusThis device complies with the requirements of GB 189.1-2008 Figure 18/19, IEC884 Figure 18/19, VDE0620, etc. It is suitable for checking the maximum force required to pull the plug out of the socket and the single pole pin pulled out from the socket assembly. Whether the minimum force required is within the range specified by
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type A, Ø0.80mm, 305gf
K100-A080305-SKAU
K100 Series, Pitch 100mil, Tip Style A, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
product
Grips and Fixtures for Force Gauges
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
product
6-Component Wheel Force Transducer
Whether vehicle dynamics tests, brake tests or determination of load spectra - the new 6-component Wheel Force Transducer WFT-Cx measures all forces and torques acting on the vehicle with high precision. The robust housing reliably protects against dirt, water and snow and allows applications in any weather.
-
product
Force Testing
Force testing is a way of determining how an object will react when it is subjected to tensile or compressive loads
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 305gf
K100-I126305-SKAU
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 305gf, Steel with Gold Plating.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 155gf
K100-H080155-SKAU
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
product
Force Tester
CS2 Series
The CS2 Series are high quality digital force testing machines optimized for production and laboratory testing of applications up to 5 kN (1100 lbf). These force testing machines are an excellent choice for simple testing within plastic, rubber, packaging, pharma, cosmetic, electronics and wood.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 155gf
K100-L150155-SKAU
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
product
Centor Easy, graphical force gauge
CNR EA
The Centor Easy force gauges are designed to meet the production needs of its users. This group offers several features which are indispensable today for quality control, for example : ease of reading with its large backlit graphical display, RS232 output, memory of the last 100 values and ability to set thresholds with visual and sound alarms.
-
product
Digital Push And Pull Force Gauge
HG-2-1000
Shenzhen Chuangxin Instruments Co., Ltd.
Digital push and pull force gauge is a universal portable force device, testing push and pull load. It is small, light, easy to take, multi-function, high precision. Applicable for all products doing push and pull load test, insert and pull out force test, destroy test, etc. It also can be combined with the machine and clamp to make up a small tester for different purposes.
-
product
Twin columns automated force test stand 36" travel - 10,000 lb
710SN
The advanced 710SN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle
KR100
K100 Series, Pitch 100mil, Receptacle, no wire wrap pin. Brass with gold finish.
-
product
Digital Force Gauges
Imada digital force gauges are highly accurate instruments that provide the precise force measurement required in quality testing that determines strength and/or functionality of a part or product. Digital gauges can be used for destructive or non-destructive force measurement applications and check both compression and tension (push or pull) forces. The high sampling rate of Imada digital gauges enables them to capture the peak force of destructive tests which occurs in milliseconds. Imada digital force gauges also feature selectable units: lbf, kgf and N and easy-to-program high/low setpoints for Go/No Go testing.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type G, Ø1.50mm, 155gf
K100-G150155-SKAU
K100 Series, Pitch 100mil, Tip Style G, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
product
Force Protection
The Durham is a high-performance, highly-mobile and easy to emplace Medium Range Day/Night Wireless Surveillance System using a state of the art day camera and a cooled, highly sensitive 640x480 InSb Focal Plane Array thermal camera with 8X continuous optical zoom. The system is image stabilized and has automatic tracking of targets. Each system consists of a Base Station and one Remote Station which can be emplaced up to 5km away for wireless operation or within 500m for fiber optic operation. A single Base Station can monitor and control up to four (4) Remote Stations. The system is powered by a generator, batteries, solar (supplemental power), or vehicle power. Other options available are laser pointers, designators, and a vehicle integration kit.
-
product
Torque and Force Calibrators
Self-contained, semi-automated, multi-functional calibrator, which provides a rapid highly accurate and safe means for calibrating and testing a wide variety of torque and force measuring instruments.
-
product
Mechanical Force Gauges
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
product
Force Distance Tester
925
The Model 925 is a low cost force-distance tester. It communicates with a Windows™-based PC to send data into an Excel format. The data can then be viewed and analyzed in tabular or graphical format. Once in the Excel format, the data can be transferred or used in any of the multiple Excel operations. This line of displacement-force test stations has a positional resolution of 0.0025 mm (0.0001 inches). Your test department will appreciate the high accuracy readings provided over the complete travel range.
-
product
High Force Large Area Bond Tester
Sigma HF
- For high force and large area- Typically for IGBT, power modules and batteries up to 1000 kgf- High axis speed- Deep access up to 80 mm- SEMI S2 safety cabinet with visual feedback- Flexible positioning of multiple work holders
-
product
Force Gauges
Mark-10 digital force gauges can be used in a virtually limitless number of tension and compression force testing applications. All force gauges are able to capture the peak force in both tension and compression and have selectable units of measurement. Force gauge capacities are available from 50 gF full scale to 2,000 lbF, the broadest force range in the industry. Mark-10 force gauges may be handheld or used with a force test stand and gripping fixtures to create a complete testing solution.
-
product
Radiation Force Balance
Radiation force balance for diagnostic and therapeutic medical ultrasound
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 230gf
K100-L150230-SKAU
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
product
Atomic Force Microscope
DriveAFM
The DriveAFM is Nanosurf’s novel flagship AFM platform: a tip-scanning atomic force microscope (AFM) that combines, for the first time, several capabilities in one instrument to enable novel measurements in materials and life sciences.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 305gf
K100-K150305-SKAU
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
product
Force Tensiometer
K100
Our universal Force Tensiometer – K100 performs high-precision, automatic and reliable measurements of surface tension and interfacial tension, critical micelle concentration CMC and contact angle on solids, fibers and powders. With high-quality components and a uniquely wide range of methods, the instrument carries out many tasks in the field of surfactant analysis and wetting measurement for your quality assurance or research.
