Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
product
Force Sensors
Our force sensors are indicated for use in modal and structural analysis, process control, and general-purpose dynamic force measurements. See our range of charge modes and IEPE force sensors.
-
product
3-Component Quartz Force Rings
260 Series
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
product
Coercive Force Meter
The meter is mainly used in measuring the coercive force of magnetic components of relays and the mechanical energy meter compensation films, which is the essential instrument of manufacturers who are producing the relays and the energy meters, etc.
-
product
Force Tensiometer
K20
Our Force Tensiometer – K20 is a robust, semi-automatic instrument for the precise measurement of surface tension and interfacial tension. Using the ring and plate method as the main tensiometric methods, it produces reliable measurements for the routine quality assurance of your surfactant solutions and interfacial processes.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 155gf
K100-I126155-SKAU
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 155gf, Steel with Gold Plating.
-
product
Full Bridge Thin Beam Force Sensors
TBS SERIES
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 155gf
K100-C150155-SKAU
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
product
Force Gauges
SHIMPO offers a range of digital and mechanical force gauges to suite every application from low capacities (0.5 lbs) to high capacities (1,000 lbs). Our gauge's features range from simple, no output models to highly sophisticated units that provide memory, statistics and data output. Our gauges are known for their strong construction and highly accurate measurements.
-
product
Force Sensors, Controls & Switches
Direct caliper motor/spindle integration for Brake by Wire systemsExtra-small form factor MSG sensors that weigh less than five gramsFacilitating system-level miniaturizationAdvanced button-type sensors designed to lower costs and improve accuracy
-
product
Atomic Force Microscope (AFM)
CombiScope
The CombiScope Atomic Force Microscope (AFM) is an advanced research instrument that provides the entry path for researchers in biology, spectroscopy and photonics. If you work with transparent samples either in air or in liquid towards nano-scale structures and (near-field) nano-optical properties investigation, the CombiScope is the right solution for you. It perfectly combines inverted optical and atomic force microscopies and unleash all the power of both techniques providing the instrument adjustment and measurement automation, high resolution and high speed. Plus it can be easily upgraded to our Raman spectrometers.
-
product
Conductivity Type (P/N) Checker By Contact Thermo-electromotive Force Method (seebek Effect)
PN-12α
*Thermo electrode and cold electrode is mounted detecting part of measuring probes*Possible to check most figure of sample such as single crystalline silicon wafer, bulk, ingot and so on*Please select from 2 types;1) 2 probe ver.(Hot probe, Cold probe),2) 1 probe ver.(Hot & Cold probe)
-
product
Steel Structure Analyzer
NOVOTEST KRC-M2 (Coercive Force Meter)
Steel Structure Analyzer NOVOTEST KRC-M2 is designed for measuring coercive force of metal products in accordance with IEC 60404-7 and is used for non-destructive testing of chemical-thermal, thermal and thermomechanical treatments, evaluation of mechanical properties and residual stresses.
-
product
Pedal Force Load Cells
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
product
Force gauge management software
CNR LOCK
CENTOR Manager is a simple, user-friendly utility that enables you to communicate with your CENTOR Easy, Star or Dual memory.It enables you to:– modify the calibration date,– reset the overload counter to zero if the sensor has not been damaged,– block access to the menus and configuration.
-
product
Quartz Impact Force Sensors
Impact-style sensors are specifically designed for impact force measurements. The sensor is typically mounted in a free-standing manner with the installed impact cap directed toward the oncoming object with which it will collide.
-
product
Brinell Hardness Tester
Beijing TIME High Technology Ltd.
Measures a material's resistance to indentation by pressing a hardened steel or carbide ball into its surface with a specific force.
-
product
Versatile AFM Optical Coupling
TRIOS
The TRIOS platform is an advanced research instrument that provides the entry path for researchers in materials science, biology, spectroscopy and photonics. TRIOS is the most versatile optical coupling platform providing three ports for optical spectroscopy measurements with top-down, side (oblique) and inverted accesses to the AFM tip and sample.If you work with opaque and/or transparent samples, either in air or in liquid looking at nanoscale structures and near-field optical properties investigation, the TRIOS platform is the right solution for you. It perfectly combines upright optical, inverted optical, and atomic force microscopies, and unleash all the power of both techniques providing instrument adjustment and measurement automation, high resolution and integration flexibility. Such performance is only available from HORIBA.
-
product
Strain Sensors
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
-
product
Coax, Contact, Receiver, 75 Ohm, RG179
610104157
Primary mating contact 610103169. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact - 5 mΩOuter Shield - 3 mΩCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
product
Deadweight Testers & Gauges
The most accurate instrument available for the measurement of pressure above a few psig is the Hydraulic Deadweight Gauge. This type of gauge operates on the principle of balancing a known mass against the force exerted by an unknown pressure on a piston of known area.
-
product
Industrial ATX Motherboard With 12/13/14th Gen Intel® Core™ I9/i7/i5/i3 Processor
IMB-M47
ADLINK's IMB-M47 ATX Motherboard is a driving force behind industrial automation, supporting 14/13/12th Gen Intel® Core™ processors, and delivering substantial improvements in performance, capacity, and GPU support through its seven PCIe slots, PCIe 5.0 compatibility, DDR5 memory, and 2.5GbE PoE capability. Tailored for a range of industrial applications including automation, machine vision, factory automation, and logistics, the IMB-M47 features up to 128GB DDR5 memory at 4800MHz, supports three independent displays, offers USB 3.2 Gen2x2 (20Gb/s), 3x 2.5GbE LAN, multi-M.2 Key M, TPM 2.0 security, and PCIe 5.0 slots for high-performance add-on cards. Optimized for the latest Intel processors, this motherboard blends efficiency and performance cores, bolstering edge applications with swift memory performance via DDR5 technology. With a commitment to technology leadership, ADLINK equips customers with the tools to harness the latest processors, streamline real-time graphics processing, and fuel innovation in Edge AI applications, solidifying its role in the future of industrial edge computing.
-
product
Accordion Custom Connectors
ECT’s Accordion Custom Connectors offer high reliability, high cycle life, patented single beam architecture providing a large range of usable compliance to absorb connector to target mating tolerances. With no requirement for a male to female target penetration, superior ease of use is achieved in blind mate scenarios with low insertion/extraction forces.
-
product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe
LFRE-1I35-4
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
product
Economic Extreme Power Temperature Forcing System
ECO Cool
ECO Cool® Economical Powerful - Thermal Forcing System.Exceptionally Powerful, Economical & Reliable
-
product
Instrumented Pendulum Impact Testing System
JB(INSTRUMENTED)
Jinan Testing Equipment IE Corporation
JB-450I/750I Instrumented Pendulum Impact Testing Machine is equipped with high precision instrumented strain-gauged striking edge & high-speed data acquisition system. This instrumented test system can measure the force of a test specimen during an impact event. Then, the instrumented test data can be used to calculate the energy absorbed by the test specimen. In addition, the crack initiation and arrest loads can be used in fracture mechanical models.
-
product
Torque Transducers
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
product
3-Component Quartz Force Rings And Links
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
product
Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Lead Free Probe
LFRE-1L-7
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
High Force Type Spring Probes
Total length of spring probes for high force is longer than standard type and is more optimized to use for testing PCB. We have 1mm to 2.54mm pitch and you can choose not only tip type but also spring force for each pitch. This makes it possible for you to choose spring probe suits the best for your use.
