AC Electronic Loads
Simulate voltage, current and power ranges.
-
product
Power Load Switches
Low-resistance power load switches offer reliable overcurrent and thermal protection. They are designed for general-purpose power protection or for applications such as USB, hot-swap and power distribution. The power switches come in 1- or 2-channel versions with fixed and adjustable overcurrent limit. Some include a USB charge controller specifically designed to optimize USB host applications.
-
product
Electronic Dosimeters & Readers
Readers operate using software packages installed on computer (PC) and communicate with DMC 3000 dosimeter and DMC 2000 and SOR families in hands-free data exchange mode. the LDM 320 reader is used as an interface to activate a dosimeter (to switch into counting mode) or to deactivate it (to switch into pause mode). When used with the included* DMCUser software, it functions as an interface to read and write the internal data of the DMC 3000, SOR and DMC 2000 dosimeters.
-
product
THRU HOLE BARE AND LOADED BOARD TEST PROBES
SERIES 93
ElectricalMAXIMUM CURRENT: 7 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS mean
-
product
Mini AC Leakage Current Clamp Tester
M-102+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・23mmφCT window and ultra compact size.・Data-hold function. Especially useful when working in dark or hard to get areas.
-
product
Dynamically Controlled, High Voltage Digital I/O PXI Card With Pin Electronics
GX5055
The GX5055 represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the GX5050, the GX5055 offers high performance pin electronics and an enhanced timing generator in a compact, 6U PXI form factor.
-
product
Load Cells
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
product
Electronic Tearing Strength Tester
DRK108B
Shandong Drick Instruments Co., Ltd.
DRK108B Electronic Tearing Strength Tester is the special instrument for tearing strength test. In paper making industry, packaging industry, science and research industry and supervision and inspection industry, it is necessary.
-
product
On Load Tap Changer Analyzer
TAP-4-PLUS
The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.
-
product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
product
electronic Consolidated Automated Support System
eCASS
electronic Consolidated Automated Support System (eCASS) will validate that the aircraft is combat ready. eCASS is the workhorse for avionics repair across the Naval Aviation Enterprise. Through automated testing at sea and ashore, maintainers are able to return equipment to readiness status quickly and efficiently. Compatibility with legacy CASS stations preserves the Navy’s investment in more than 550 Test Program Sets supporting 750 avionic components.
-
product
Low Profile Compression Only Load Column Load Cell with Mounting
CLC SERIES
Our CLC Series is our high capacity compression only load cell, featuring low profile compact size for a wide range of portable and dedicated applications. The loading diameter (D1) is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. All ranges are made from 17-4ph heat treated stainless steel and incorporate a stainless steel molded connector system designed to resist washdown and splash. The mating connector, sold separately, is available in three different cable lengths.
-
product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
product
AC Power Sources
MX Series
AMETEK Programmable Power, Inc.
The California Instruments MX Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the California Instruments MX series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the MX15, MX22.5, MX30, or MX45 unit to its designated location (using included casters), plug it in, and the MX series is ready to work for you.
-
product
Road Load Data / Durability
Vehicle Durability Testing and Road Load Data AcquisitionA road load data acquisition system from Dewesoft is a perfect vehicle durability testing solution for real-drive tests or tests on the road simulator test benches. Our advanced DAQ technologies will shorten time to test dramatically and make sure you get the correct measurements right the first time.
-
product
MTM-Load-1: 1-Channel DC Load Module
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.
-
product
Load Banks
BD Series
*12 kW, 15kW and 18kW Battery Discharge Load DC*All of our Load Banks are continuously rated for Power and Current.
-
product
AC Line Separators
ALS-2
Standard Electric Works Co., Ltd
● x10 Model allows for more accurate measurements of low amperage devices.● Direct reading x1 mode.● 4mm Voltmeter input jacks.● Intergrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40PS
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～500A*Current measurements of feeder
-
product
Programmable AC Power Source
Chroma Systems Solutions, Inc.
The Chroma programmable AC power source 61500/61600 series are the right solutions to meet complex single and three phase requirements due to their ability to simulate AC line conditions and measure critical product characteristics during testing. These features make the 61500/61600 series ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification and quality assurance to mass production.
-
product
AC Hipot Tester (Digital)
KT-5000PD-2D
This Hipot(puncture) Tester is shows a leakage current on digital meter while test.Also good, bad, test, enable signal exchange from External equipment, and it is a precision measurement equipment the system connection is easy.
-
product
DC-Powered, AC Voltage Monitor
VAD/VQD
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
product
Electronic Load Board 3U CPCI-S (air cooled)
056-377
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
Electron Microscope Analyzer
QUANTAX EDS for SEM
Bruker's latest generation of QUANTAX EDS features the XFlash® 7 detector series, which provides the largest solid angle for X-ray collection (also called collection angle) and the highest throughput.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Electron Microscope Analyzer
QUANTAX EBSD
QUANTAX EBSD system, with its popular OPTIMUS 2 detector head, is the best available solution for analyzing nanomaterials in the SEM
-
product
Split type AC Current Transformer
CTS-100
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy installation by metal fitting.
-
product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Top Load
12R2-8U-TL
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
product
Through Hole Type AC Current Sensor
CT-13K
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*High accuracy and compact size.*Measuring range:AC 1A～50A.
-
product
Programmable DC Electronic Load
M97 series
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications. From 150W to 200KW, there are many models to choose from :
-
product
Battery Loading Unit
BLUe
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
