-
Product
Debug Probes
J-Link and J-Trace
-
SEGGER Microcontroller GmbH & Co. KG
SEGGER J-Links are the most widely used line of debug probes available today. They've been proven for more than 10 years with over 250,000 units sold, including OEM versions and on-board solutions. This popularity stems from the unparalleled performance, extensive feature set, large number of supported CPUs, and compatibility with all popular development environments.
-
Product
Microscopic Probes
M12PP
-
CAPRES M12PP Microscopic Twelve-Point Probes are specialized versions of the CAPRES Micro Multi-Point Probes. By using a dedicated 12-by-4 multiplexer, a total of 495 different pin-configurations can be obtained, each with different probe pitch. This is utilized in e.g. the CIPTech, where 8 or more combinations are used to obtain a “depth profiling” of the measured structures.
-
-
Product
Sanitary Probes
-
Used in the food, beverage, dairy, and pharmaceutical industries, these hygienic/sanitary probes carry 3-A certification, which is required in these sanitary, wash down, & clean-in-place applications.
-
Product
TSP138 Switch Probes
Switch Probe
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
Product
AC Current Probes
CWT
-
Power Electronic Measurments Ltd
The CWT Rogowski current probe is suitable for measuring AC currents ranging from 300 milliamps to hundreds of kA from below 0.1Hz to >30MHz.
-
Product
Beam Probes
-
The CO2 Laser Beam Probes are hand-held plates designed to simplify the alignment of IR optical systems. They display the laser beam as a dark image on a fluorescent background using the same UV-excited, thermal-sensitive surfaces developed for Macken Instruments'' Thermal Image Plates.
-
Product
Conical Laser Power Probes
-
Conical Head Power Probes are used to measure high power density CO2 laser beams which may damage the standard flat surfaced Power Probes. The conical absorbing cavity exhibits a high heat dissipation.
-
Product
Probes, Magnetic Field
EM-6880 | 9 KHz – 520 KHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
Jandel Four Point Probes
-
Jandel probe heads are manufactured solely by Jandel Engineering Limited and there is one to fit all mountings and systems known to us.
-
Product
Optical Communication Probes
-
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
Product
BIP-10 Battery Probes
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 30Resistance Remark: Probe Resistance Steel: 30 mOhms, Gold plated: 100 mOhmsTest Center (mil): 260Test Center (mm): 6.60Full Travel (mil): 157Full Travel (mm): 4.00Recommended Travel (mil): 126Recommended Travel (mm): 3.20Overall Length (mil): 591Overall Length (mm): 15.00
-
Product
ICT Probes
Merica Serirs- MP175
-
Minimum Center: 1.91mm (75mil)Current Rating: 3amps, continuousContact Resistance: 40milliohmsMounting Holes Size: 1.35Full Stroke: 6.40mmRated Stroke:4.30mmSpring Force: 203gf (7.2oz)/227gf(8oz)
-
Product
Trident Fiber-Optic Probes
Fiber-optic Probe
Our most popular and cost-efficient option for the test of multiple LEDs — testing three LEDs with a single Sensor. This method of testing LEDs scales up, so that testing 3, 30, 300 — or any number of LEDs — is far more cost-efficient than other methods. This is our most popular Fiber-optic Probe and can be combined with any of our Universal LightProbe Sensors.
-
Product
CP-059-025 Battery Probes
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 313Overall Length (mm): 7.95
-
Product
Profile Probes
-
Consist of several temperature sensing points inside one probe. Used to profile the temperature at various points along a single axis. Great for measuring the temperature distribution in tanks.
-
Product
CMM probes, Software and Retrofits
-
The 5-axis measurement product range represents the biggest step-change in measurement capability ever introduced, delivering unprecedented speed and measurement flexibility, whilst avoiding the speed versus accuracy compromises inherent in conventional techniques. Whether the REVO scanning or the PH20 touch-trigger, Renishaw's 5-axis systems boost measurement throughput, minimise lead times and give manufacturers a more comprehensive appreciation of the quality of their products.
-
Product
TSP100 Switch Probes
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
High Voltage Probes
-
High voltage measurements have a variety of different requirements, and our PVM series and VD series probes are designed for most of these requirements. The PVM probes are designed for wide bandwidth and ease of portability where a variety of measurements must be made. The VD series probes are designed for use at higher voltage ranges, and where physical stability is required.
-
Product
Current Probes
-
Current probes allow you to measure DC or AC current. Yokogawa's selection of current probes allow measurements ranges up to 500 ARMS and bandwidths up to 100MHz.
-
Product
Battery Probes
Battery Probe
Offer a wide range of terminations for SMT, PTH or double-ended probes for simplified hardware mount solutions.
-
Product
Low & High Voltage Differential Probes
T3
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
-
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
-
Product
Spring Contact Probes
-
Spring Contact Probes - Test Center: 50 - 100 milsCurrent Rating: 3 - 5 ampsContact Resistance: 30 - 50 milliohmsSpring Force: 113 - 312 gf (4-11 oz)
-
Product
Ultrasonic Immersion Probes
SONOSCAN I
-
The SONOSCAN immersion transducers for Non-destructive Testing (NDT) are mainly used to test metals and plastics for the smallest material defects. For example, binding defects, welding defects or cracks and pores in metal parts can be detected. The powerful, robust ultrasonic probes can be connected to all common ultrasonic testing devices. Due to variable designs and sizes, the immersion probes guarantee optimal use. In addition to ultrasonic standard pobes, we also offer customized transducers according to your individual specifications.
-
Product
High Frequency Coaxial Analytical Probes
-
D-COAX offers four analytical probe models: HyPac model for package characterization, and two models, Omni and OmniJet, for board level characterization, and DP1.4mm differential, single-ended probe.
-
Product
Touch-Trigger Probes
-
Touch-trigger probes measure discrete points, making them ideal for inspection of 3-dimensional geometric parts.Renishaw provides a comprehensive range of systems to meet the application needs and budget constraints of all users, from simple feature checks on manually operated CMMs, to complex part measurement on high-speed computer controlled machines.
-
Product
SPM Probes
-
AppNano silicon probes are manufactured out of prime grade, low resistivity (0.01- 0.025 Ω-cm), n-type antimony doped, single crystal siliconOur well-established silicon technologies combined with novel micro-fabrication processes achieve consistent high quality monolithic probes with unprecedented tip sharpnessWe have many standard silicon probe series designed for a wide variety of applications that are compatible with most AFM equipment in the market
-
Product
Scanning Probes
-
3D Laser Scanning Probes for your existing CMM are options for full-time or part-time use. Laser Design’s broad range of scanning probes ensures a perfect fit between the scanner and the size and detailed features of your parts.
-
Product
Switch Probes
Switch Probe
Switch point flexibilityDesigned for long life and reliable performanceVariety of tip options
