-
Product
Fully Automatic Tensile Testing System
-
This is a fully automatic tensile testing system for metals. The system is fully automated from supply of specimens, measurement of specimens, tensile testing, recovery of specimens, and data processing, and is capable of continuous nighttime testing.
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Product
Hi-Pot Testing
-
The CableEye HVX System combines our M3U tester with a high voltage module to provide Hi-Pot testing of insulation resistance and dielectric breakdown up to 1500Vdc and 1000Vac.
-
Product
Testing Wiper Motors
-
Magtrol developed two automatic testing benches for front wiper motors, rear wiper motors (pendulum with measure of angle) and ABS motors (excenter). The test setup is equipped to handle torque ratings from 3 to 50 Nm and a speed range of 0 to 10,000 rpm
-
Product
Soil Testing Instruments
-
Soil water hardness meter, soil moisture meter, soil nutrient tester, soil salinity tester, soil water potential tester
-
Product
Electrical Components Testing
-
To be successful on the market, the safety, quality, durability, and reliability of your products are essential.Manufacturers are responsible for ensuring that the products they place on the market meet all relevant regulations. Ensuring that your customers receive safe components of high quality is critical to the longevity of your business.Every part of an electrical appliance can be hazardous and one defective component can lead to disastrous results. Our experience and scope of accreditations help you to meet local and global electrical product safety regulations. As one of the largest certifiers within the CB Scheme TÜV Rheinland Group has vast experience in a broad range of product testing.
-
Product
Battery Boxes Testing Equipment
-
Battery boxes can be tested for faults by placing the box on a metal plate. By applying a test voltage to an electrode inside the box, the moulding can be checked thoroughly - particularly at the injection points - and any faults found. Defects will be identified by a spark passing from the electrode, through the defect itself, to earth (the conductive material placed outside the battery box.
-
Product
Low Resistance Or Continuity Testing
-
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
-
Product
LTE eNodeB Testing
-
The DuoSIM and DuoSIM-Advanced are the most scalable eNodeB test systems in the industry. From basic functional testing to complex C-RAN environment simulation, the DuoSIM line of testers makes validation and development of network equipment faster, easier, and more cost effective.
-
Product
Performance Testing
-
If you want to check the strength of your application or the server’s strength you will need to find out how much load, in terms of the number of users the application can handle. We use the Performance Testing techniques, to check the load an application can handle.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
-
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
Telecom/NEBS Testing
-
Eurofins E&E North America’s extensive capabilities in telecommunications include testing, compliance assistance & design reviews, application preparation and agency liaison. Eurofins tests products for compliance to U.S., Canadian, and international standards for telecom devices, from NEBS equipment to consumer products such as DSL modems.
-
Product
Thermal/Mechanical Testing
-
Accolade Engineering Solutions
As new products employ advanced materials and processes, the need to measure and characterize those material properties becomes increasingly important. DSC is used to measure heat flow in to or out of a material. Some DSC applications include measurement of melting temperature, polymorphic transitions, crystallization temperature, thermal stability, heat of fusion and degree of cure. TMA is used to measure dimensional changes of a material as a function of temperature.
-
Product
AI Powered Software Testing Services
Astute
-
Leveraging 12+ years of deep experience in test and QA, Infostretch developed ASTUTE – an AI-powered quality engineering suite comprised of intelligent testing services and BOTs that leverage advanced machine learning techniques to optimize every aspect of your testing cycle from discovery to maintenance.
-
Product
Mobility Simulator Creates V2X Environments For Testing
MxDrive™
-
MxDrive is a multi-vehicle and infrastructure mobility simulator that provides an environment to generate and run real-world conditions to test connected vehicle applications. Testing V2X applications on actual roads has limitations. Only a limited number of test conditions can be achieved, while safety and damage risks further limit test coverage. MxDrive combined with the MxSuite ecosystem significantly simplifies the testing of Advanced Driver Assistance Systems (ADAS), Sensor Fusion, Radar, and V2X. MxSuite is ISO 26262 qualified to test safety applications for OEMs and suppliers.
-
Product
Vehicle Testing
-
short testing times, thereby enabling a large throughput of vehicles;objective, operator independent test results on most test items;accurate measurements;a large set of clear user instructions is displayed, which allows the owner/ driver to stay in the vehicle during the test, thus saving manpower;a wide selection of different test equipment for integration is available;a large number of settings, threshold values and standards can be accessed directly and edited by the user;the modular setup allows a complete variety of Test Lane configurations;easily upgradable by adding more test equipment items per lane;easily expandable by adding more Test Lanes;integration of Test Lanes on remote sites is possible;link up to Government database and remote access possibilities where applicable.
-
Product
Blockchain Testing
-
ZenQ’s BlockChain Testing Centre of Excellence provides Testing services for Blockchain platforms and implementations.
-
Product
Moisture Testing
-
Determine moisture in concrete and other construction materials. Meter for rapid determination of moisture content in sand and other fine or coarse aggregates. moisture content in Solid Materials. Includes Meter, Test Cable and Case. Meter for the Rapid Determination of Moisture Content in Different Types of Soil. Determination of Water/Cement Content Ratio in Fresh Concrete. (Type R for Regular Water Cement Ranges. Type L for Low Water Cement Ranges.)
-
Product
In House Testing
-
Burnsco Environmental Test Chambers
Burnsco Technologies Inc recognizes that many customers have one-time testing requirements or, from time to time, an overload of testing. With that in mind we are pleased to offer you a test center with a unique difference!
-
Product
EOL RF Functional Test
AS652
-
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
Product
Hazardous Locations Product Testing
HazLoc
-
F2 Labs can assist you with your hazardous location testing needs. We can perform the HazLoc product testing required to ensure that your product won’t cause a fire or explosion in an area where flammable or combustible materials (such as dusts, gases, fibers or vapors) are present. The product must be designed using various methods of protection.
-
Product
Material Testing Software
TRAPEZIUM X
-
Windows 10 compatible TRAPEZIUM X can carry out various tests ranging from simple test control to complex custom-made patterns, using the industry's first data search and preview function, free layout reports, visual wizard settings, quick panel, and quick conditions lists.
-
Product
Glyphosate Testing Solutions
-
Glyphosate is a chemical herbicide used during cultivation of cereal grains, pulses, oilseeds, sugar beets and more.The International Agency for Research on Cancer (IARC) classified glyphosate as a Group 2B probable carcinogen in 2016. Since that time, at least 35 countries, regions and municipalities have moved to restrict or ban the use of glyphosate for commercial and noncommercial use.
-
Product
Universal Testing Systems (Up To 2000 KN)
Industrial Series (DX, HDX, KPX)
-
The Instron static hydraulic universal testing systems — part of the Industrial Series — are rugged, high-capacity frames built for demanding material tests in tension, compression, flexure and shear up to 2,000 kN. Featuring large-diameter columns and rugged components for superior frame stiffness and durability, these systems deliver reliable, repeatable performance for high-force testing needs in metals, composites, concrete, fasteners, and structural materials.
-
Product
Performance & Load Testing for APIs, Mobile and Web Apps
-
Test the performance of any mobile app, website or API in under 10 minutes. Simulate up to one million users with our developer-friendly, self service platform. 100% compatible with Open Source Apache JMeter. Supports Selenium.
-
Product
Stability Testing Chambers
-
A stability testing chamber is a specialized enclosure used to control and maintain specific environmental conditions, primarily temperature and humidity, for extended periods. It's used to assess the stability and shelf life of products, materials, or substances by subjecting them to controlled environmental stress.
-
Product
VLSI Test System
3380
-
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
Military Communications Test
-
Astronics testers for military radios and wireless communications systems help you keep your most critical communications up and running smoothly. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in operation.
-
Product
Biosafety Testing
-
Biological products derived from mammalian cell lines pose an inherent risk for the introduction of microbial or viral contaminants. In addition, the manufacturing process or product itself may introduce impurities that must be characterized.
