-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
-
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
NVMe® Technologies
-
We have been a leader and expert in NVMe Testing Services for several years providing conformance and interoperability testing. In addition, we also host NVMe Plugfests where storage vendors from around the world come together to test against NVMe standards to qualify them for the NVMe Integrator's List. The NVMe Integrator's List currently consists of configurations that have proven to be interoperable and conformant to NVMe standards.
-
Product
Fuel Injection Pressure Tester with 2 Gages in Case
33980
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with multi-port and some throttle body injection (TBI). Test all Chrysler cars with multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.
-
Product
AC Warning System
AC-15
-
Monitors AC on pipelines or structuresAlarm at 15v AC ThresholdConforms to NACE SP0177-2007Audio and Visual AlarmsCalibration Test UnitSuperbright LED'sReplaceable 9v Batteries
-
Product
Voltage Stabilizer
MS 7643
-
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
Product
Cable Test and Diagnostics
-
Cable testing and diagnostics provides information about the cable’s global condition (e.g. the cable’s overall insulation system), and will reveal localised problems, such as poor joints and terminations; it will also reveal localised weak spots in the insulation. Various cable tests are carried out to spot potential failures before they can cause severe outages. Megger cable test equipment provides access to all of the technology needed to make informed cable management decisions through the different stages of the cable’s life cycle.
-
Product
Mixed Signal Automated Tester
MSAT
-
Whether you are testing radar systems for the Department of Defense (DoD), or the next actuator circuit card for aircraft landing systems, ARC’s Mixed Signal Automated Tester (MSAT) offers flexible automated testing capabilities for nearly every budget.
-
Product
DUT Boards
-
RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.
-
Product
Teraohmmeter/IR Tester
98x
-
The new 981i and 983i Teraohmmeters are designed to tackle the toughest High Resistance measurement applications. Demanding applications that most other IR testers won’t measure up to. So when it’s time to test higher voltage IR values like today’s electric vehicle systems and higher voltage solar arrays — look to Vitrek to deliver the IR tester you need for your production line.
-
Product
Singlemode Power Meters and Laser Sources
-
The KD Optics range of Singlemode power meters and Laser sources are designed for the testing of SDH, CATV, Telecom and other singlemode links. The power meters are highly accurate with a wide dynamic range, while the laser sources feature a very quick stabilisation time, promoting accurate readings.
-
Product
Power Electronics Test Bench
OP1300
-
The multi-purpose and ready-to-use Power Electronics Test Bench combines a state-of-the-art Hardware-in-the-Loop (HIL) simulator from OPAL-RT with Imperix’s Rapid Control Prototyping (RCP) system and real power hardware. It enables rapid development of power electronics, drives and smart-grid applications across industry and academia.
-
Product
CREST Penetration Testing
-
CREST is a not for profit organization that serves the needs of a technical information security marketplace that requires the services of a regulated professional services industry.
-
Product
Meter Test & Calibration
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for meter test and calibration including portable power source, standard reference meter and meter test system. All products are accredited to the highest production standards with different options of measurement accuracy (class 0.05 and class 0.1).These enable them to cover different applications for test and calibration of different types of energy meters, electric transducers, indicating meters and so on.
-
Product
Dual Mobile Communications DC Source w/ DVM
66309D
-
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66309D dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a half rack box) and eliminates the need for two separate power supplies.The 66309D dc source provides all of the capabilities of the 66309B with the addition of a built in digital voltmeter.
-
Product
20MHz Pulse / Function Generator
Model 2019A
-
- Versatile Waveform Generation for a Wide Range of Testing Application- Wide Range of Frequencies from 0.0002Hz (i.e. 5000s) to 20MHz (i.e. 50ns)- Choice of Eight Selectable Waveforms- All Outputs can Drive 50 ohms Terminations- Trigger and Gate Modes with Adjustable Start/Stop Control
-
Product
Test Device for Bicycle Batteries
ATGF 1500/PBG
-
The ATGF 1500 is a multifunctional testing instrument for bicycle batteries and accompanying battery chargers. The easy to use ATGF 1500 is suitable for battery systems of Derby Cycle, Gazelle, Simplon and ZEG. est programs: Quick Test, Capacity Test, Recalibration.
-
Product
Digital ELCB (RCD) Tester
1812 EL
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2Lines × 16 Characters LCD.● Very low consumption.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Zero Crossing Circuitry permit testing at 0° or 180°.● Disconnection Phase Polarity shown on LCD display.● Auto-off and off override.● Polarity Trip indicator (Positive of Negative Phase).● Wiring polarity indicator.● Measure voltage and frequency between Line and Earth before testing.
-
Product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Dual-Channel High Speed Power meter
JW8103
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8103 Bentch top Dual-channel High Speed Power Meter is according to the newest optical power test requirements ,combined with the technology characteristics of the power meter in domestic and overseas; the dual channel high speed power meter with very fast sampling rate(can achieve 51200 sampling point per second) and fast stable time, greatly improve the test efficiency；provide large InGaAs detector and adaptors，make it suitable for bare fiber environment and dynamic range test；provide more comprehensive menu settings function，for many test situations to use.
-
Product
BNC (M) To Minigator Test Clips
2886
-
Converts BNC (female) cables / connectors to minigator test clips for test versatility.
-
Product
Wide FOV Target Projector
-
The Model 13792 is a broadband portable target projector used for characterizing the performance of a wide variety of infrared sensor systems. The system incorporates SBIR standard components to provide accurate and precise stimulus to sensors under test in laboratory, depot and production line environments. Testing can be automated with the use of IRWindows™ test system controller that reduces test times and cost, while improving the consistency and accuracy of test results.
-
Product
Phase Noise Test System
PN9000 System
-
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
PXI Dual 8 Channel Switch Simulator
40-485-121
-
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
PXI-2542, 6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module
778572-42
-
6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module - The PXI‑2542 is a terminated switch module suited for routing RF signals for production test applications. It features high-performance solid-state relays that offer unique benefits such as unlimited mechanical lifetime and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel. The channel termination and COM lines help minimize reflections of the RF signal and protect your instruments.
-
Product
FPC Test Connectors
-
FPC Test Connectors (Clip Connectors) can easily be inserted and can be used for repeat testing, saving time and money as well as minimizing damage.
-
Product
Software
Electrochemistry Tests
-
Materials Development Corporation
CyclicVoltammetry and Galvanostatic Charging are tests used throughout the industrial and scientific communities to study chemical reactions and behavior of electronic structures. They are extremely helpful in the monitoring of nano based dielectrics, used in super /ultra capacitors or self-assembled monolayers (SAMs). The Cyclic Voltammetry test applies a ramping voltage to a device and measures the resulting current. In acapacitor-like structure the current reveals loss in the dielectric as well as degradation over time. CyclicVoltammetry is used to characterize the performance of supercapacitors and ultracapacitors formed using various nano-technologies. It is also useful in the studies of self-assembled monolayers used for sensors.
-
Product
Analyzers and Timers
CAT Advanced Series
-
Description The Advanced CAT Series Analyzers and Timers are stand-alone or PC-controlled digital instruments for circuit breaker status evaluation. Timing channels record arc closing and opening, resistance and auxiliary contacts. The main contact channels can also measure the resistance value of pre-insertion resistors (if present in the breaker). The advanced CAT series records graphs of the opening and closing coil currents and the movements of the moving parts of the high and medium voltage circuit breaker. Test results are printed on the 112 mm (4.4 inch) thermal printer (optional accessory) in tabular and graphical form. The advanced CAT series provides easy selection of different operating modes:
-
Product
PXIe-5451, 145 MHz, 16-Bit, 512 MB, PXI Waveform Generator
781204-02
-
PXIe, 145 MHz, 16-Bit, 512 MB, PXI Waveform Generator—The PXIe‑5451 is a 145 MHz, dual‐channel arbitrary waveform generator capable of generating user-definied waveforms, standard functions, and I/Q communications signals. It is an ideal instrument for including in systems for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator as wells as time-domain signals like envelope tracking. The PXIe‑5451 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5451 also features advanced synchronization and data streaming capabilities.
-
Product
Software
BatteryPro
-
Chroma Systems Solutions, Inc.
The software is item driven with built-in tests – meaning no programming is required at all. Users are able to read data from the BMS controller and also includes thermal chamber control. Battery Pro Software supports Chroma’s regenerative battery cyclers and provides a safe and stable testing environment.
