-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
Oscilloscope - 500 MHz, 2 Analog Channels
DSOX3052T
500 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782264-01
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
Frequency Multipliers
Analog Devices active and passive frequency multipliers enable designers to economically multiply lower frequencies to higher frequencies without creating measurable additive phase noise. This broad portfolio features a range of devices that can meet the size, volume, and cost needs for multiple applications, including:
-
product
Modbus RTU Analog Input
Provide direct connection to a wide variety of sensors to any host with an RS232 or RS485 port. The modules perform all signal conditioning, scaling, linearization, and A/D conversion. They each contain some discrete digital I/O lines and can measure signals such as:
-
product
Power Amplifer AURORA Digital Interface For Simulator Application
PAV DIA01
PAV DIA01 is the optional accessory unit and Aurora digital interface for PONOVO’s power amplifiers which could convert the analog input signal into digital signal, supporting communication between power amplifier and simulators via AURORA protocol.
-
product
Linear Power Supplies Voltage Stabilizer/Current Limiting, Ultra Low Ripple/Noise
Series JQE
Series JQE power supplies are systems-type voltage stabilizers with current limiting. They are available in a variety of ratings: 100 watts in a 1/4-rack package, 250-500 watts in a 1/2-rack package, and 1000 watts in a full-rack package. These power supplies offer ultra low noise and ultra low ripple at the output. They are MIL-STD-461 compliant.The traditional analog meters (M Models) have been replaced by digital meters on DM models. Availability of models with analog meters is limited and they will be discontinued in the future.
-
product
Bit Waveform Digitizer Board
ATS9373
ATS9373 is a 12 bit waveform digitizer board that can sample one analog input at rates up to 4 GS/s or two inputs at 2 GS/s. With on-FPGA FFT signal processing and data throughput as fast as 6.8 GB/s (6800 MB/s), ATS9373 is an ideal solution for many applications, including next generation OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - XMC
Model 71891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
-
product
Miniature Absolute Magnetic Shaft Encoder
MA3
The MA3 is a miniature rotary absolute shaft encoder that reports the shaft position over 360 with no stops or gaps. The MA3 is available with an analog or a pulse width modulated (PWM) digital output.
-
product
Portable Laser Power & Energy Meter
StarLite 7Z01565
*Brilliant large size TFT 320x240 display*Compact handheld design with rubberized bumpers and optimized kickstand*Choice of digital or analog needle display*Select between English, Japanese, Russian and Chinese interfaces*Analog output*Easy to use soft keys*Easy measurement configuration with context sensitive help*Backlighting and rechargeable battery*Single shot energy measurement with thermal sensors*Power averaging*Resizable Screen graphics*EMI rejection
-
product
AMIDA 5000 Tester
AMIDA 5000 is a high-end performance test system, combining analog, mixed-signal and logic with the latest test solutions. High pin count - as many as 512 smart multi-function pinframes and 128 sites. Ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. This system has a higher number of parallel tests and a higher level of capability. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The 5000 series test system is the best analog, mixed signal, digital IC, PA test system for engineering verification and mass production. It can be easily connected to all well-known wafer probing machines and sorters, and also supports parallel test functions. The 5000 series meets customers' needs for high-precision, high-resolution, high-reliability, user-friendly, and low-cost testing and measurement of test systems.
-
product
Mass Flow Controller for Medium Flow
HFM-201 / HFC-203
The HFM-201/HFC-203, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-201 / HFC-203 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Many corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
product
PXI Analog Output Module
PXI Analog Output Modules support both static and software-timed voltage output applications. Modules also include 5 V TTL/CMOS digital I/O lines. Some PXI Analog Output Modules can deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. These advanced features enable you to use the PXI Analog Output Module to replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.
-
product
GPIB Analog Interface
Model 4861B
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
product
Extension Module
GE-AI-4
Infinite Industrial Informatics Lt
GE-AI-4 is a DIN rail mount, analog input expansion module with I2C serial communication interface. It can be used for the analog input expansion of Infinite's products as the SCOM-100 GSM controller and the iLOGPlus RTU/Data Logger.
-
product
FTTH Optical Node
SRXG-2020AW
Hangzhou Softel Optic Co., Ltd.
SRXG-2020AW, the operating bandwidth of 47~1000MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver, Whether used in analog television or digital television. Products with high sensitivity optical receiver tube and special low noise matching circuit. Receiving at high optical power can be adjusted by PAD level, played limiting output, so SRXG-2020AW within a large dynamic range of the received optical power of +2 dBm ~-21dBm, have excellent characteristics.
-
product
High Output Current Op Amplifiers ≥ 100mA
Analog Devices high speed , high output current (≥100 mA) op amps deliver high output current while driving low impedance loads with excellent linearity. Whether it's high output current, low input bias current, wide bandwidth, high slew rate, or low distortion, no one sets more performance standards for next-generation designs with the widest portfolio of leading edge products than Analog Devices.
-
product
Lighting ICs
Based on its 30-year experience in power conversion and high-voltage technology, ST offers a wide portfolio of solutions for electronic ballasts, ranging from high-voltage ballast controllers for analog solutions (with or without embedded PFC), to complete power management units with integrated drivers and voltage regulator for digital platforms.
-
product
Boundary-Scan Test and In-System
PCIe-1149.1
The Corelis PCIe-1149.1 is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the PCIe-1149.1 offers up to 80 MHz clock rates on 4 or 8 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
4 High-Voltage/High-Current (External VCC) D/A Outputs
DA5
Digital-to-Analog (D/A) module DA5 provides 4 independent D/A output channels (half-bridge) utilizing a single external supplied power source with full-scale operating range of 0-65 VDC (V-control mode) and 0-2 A (I-control mode). Alternatively, two channels can be paired (full-bridge) to achieve a full-scale operating range of ±65 V and ±2 A from a single external supplied power source. Linearity/accuracy is ±1% FS range over temperature. The DA5 provides either voltage or current control loop modes, which are programmable for the application.
-
product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782259-01
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Oscilloscope 70/100/200 MHz, 2 Analog Channel
DSOX1202G
The DSOX1202G oscilloscope provides 70, 100, or 200 MHz of bandwidth on 2 analog channels, and waveform generator.
-
product
PCIe-6361, PCI Express 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device
781050-01
PCI Express 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device - The PCIe‑6361 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Debug Hardware
To record your digital and analog signals, just press start. You can fill your entire computer’s memory with data so it is easy to capture lengthy or rare events.
-
product
PXI 8-Slot BRIC Matrix, 230x8, 1-Pole (5 sub-cards) Dual Bus
40-560B-121-230X8-M
The 40-560B-121-230x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
product
PC/104-based Analog Input, Analog Output, and Digital I/O Board
PCM-MIO-A-1
The PCM-MIO-A-1 is a versatile, PC/104-based analog input, analog output, and digital I/O board designed for high-accuracy and high-channel-count analog and digital I/O. The board is based upon Linear Technology’s precision converters and voltage references which require no external calibration. The digital I/O utilizes WINSYSTEMS’ versatile WS16C48 Universal I/O controller functionality, also available on many of our SBCs and other I/O products.
-
product
Compact Differential Pressure Transmitters
Series 668B/D
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
