Exposure
-
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Exposure Systems
Model 2000AF & 2000SM
-
The OAI Model 2000 Exposure Systems may be configured as either an edge-bead exposure system (2000SM) or a flood exposure system (2000AF); both configurations are based on OAI’s proven, time-tested platform.
-
Product
Exposure Systems
Model 2012AF & 2012SM
-
The Model 2012AF Flood Exposure System provides a cost-effective method for automated flood exposure. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.The Model 2012SM Automated Edge-bead Exposure System provides a cost-effective method for edge-bead removal using standard shadow mask technology. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.
-
Product
Lightning, Exposure Meters
-
Lutron Electronic Enterprise Co., Ltd.
Lightning, Exposure Meters by Lutron
-
Product
Vibration Exposure Timers
-
EU Directives and the UK Regulations specify specific daily exposure limits, which can be translated into the HSE's Exposure Points. Points are determined quantifying the Vibration Level of tools and the Time that operators are exposed to the vibration, named Exposure Time.
-
Product
Human Exposure Measurements to Luminaries
-
Through different ways of coupling between luminaries and humans, a level of exposure of a person to electromagnetic fields can be derived. One part of the exposure is based on capacitive coupling between lighting equipment and person. This creates induced internal electric field that must be evaluated using an EMI receiver and a Van Der Hoofden test head.
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
-
Product
Exposure Systems
sX series
-
Exposure systems are equipment or systems designed for the assessment of, for example, health risk, efficacy of therapies or mechanisms associated with exposure to electromagnetic fields. The systems designed by the IT''IS Foundation are the sX series, where sX stands for "System for eXposure" with options for cells (c), vertebrates (v), and humans (h).
-
Product
LITHOSCALE® Maskless Exposure Lithography Systems
-
Maskless exposure lithography systems represent an entirely new product platform of EVG lithography equipment.
-
Product
Sound Level Meter
SoundTrack LxT
-
The SoundTrack LxT® Sound Level Meter was developed to meet the unique needs of those involved in workplace noise exposure assessment and plant noise surveys.
-
Product
Domino Symphony PCIe
-
Four 10-bit 65 MHz A/D converters with four 8- or 10-bit LUTsPCIe x1 busD³ technology for extremely low synchronization jitterSupport for mega-pixel progressive-scan and interlaced cameras, asynchronous reset and exposure controlTrigger, strobe and general purpose I/O lines
-
Product
Human Vibration Management Software
HVManager
-
HVManager is a Risk Assessment and Recordkeeping software tool for reporting Vibration measurements and predicting Personal Exposure Levels. It provides reports of vibration measurement data from hand-arm and whole-body measurements acquired from the Larson Davis HVM100 Human Vibration Meter and produces vibration database records by tool type and serial number. HVManager also compiles cumulative predicted vibration exposure levels from any combination of tools and task durations taken from the measurement database.
-
Product
UV Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
* UV test chamber simulates damaging effects of long term outdoor exposure of materials and coatings by exposing test samples to varying conditions of the most aggressive components of weathering – ultraviolet radiation, moisture and heat. * UV test chamber use fluorescent lamps to provide a radiation spectrum centered in the ultraviolet wavelengths. Moisture is provided by forced condensation, and temperature is controlled by heaters. Based on your testing sample’s size, We has two options uv test chambers for choice.
-
Product
Preconditioning
-
Preconditioning is performed prior to package level reliability testing to simulate the effects of board assembly on non-hermetic devices where moisture may have been absorbed during normal storage. The subsequent exposure to high temperature during infra reflow assembly can cause internal damage such as “pop corning” and delamination.
-
Product
Intensified Cameras
-
Excelitas offers a broad range of single to multi-channel image intensified cameras through our renowned pco.dicam series. With extreme short exposure times down to 2.5 ns, our pco.dicam cameras offer the ability to precisely address ultra-fast processes far beyond the capabilities of any other camera type. Featuring state-of-the art scientific CMOS sensor technology, our pco.dicam intensified cameras combine high resolution, fast frame repetition rates, 16-bit dynamic range and extreme sensitivity for efficient single photon detection.
-
Product
EYE Super UV Tester
-
UV rays are the greatest cause of product deterioration. This unique system dramatically intensifies the deterioration acceleration caused by UV rays. It can achieve an acceleration factor greater than 100 times normal sunlight, producing material effects equivalent to extended outdoor exposure. Its compact size makes it ideal for research and development testing of paints, inks, pigments and fibers as well as plastics.
-
Product
EMF Measurements Antennas
-
An isotropic antenna that allows to carry out radiated emission and environment exposure measurement (elettrosmog) to the radio frequencies in proximity of radio and television stations and repeaters for mobile telephone.
-
Product
Beam Panoramic Power Supply Battery Crawler 40 to 160 kV
CP160CR
-
Designed to fit into 6” pipelines and higher, the CP160CR constant potential X-Ray generator for crawlers is – in its category – the most powerful panoramic X-Ray tube head in the world for crawlers. The generator is making the cutting edge constant potential technology of the CPSERIES even more compact into a 9.9 kg – 120 mm diameter X-Ray tube head. The crawler unit is capable of penetrating up to 28 mm of steel in 10 minutes, which corresponds to just a 25 second exposure time for 6” standard pipeline welds.
-
Product
13MP 4K Camera Module
e-CAM131_CUMI1335_MOD
-
e-CAM131_CUMI1335_MOD is a high performance, 13 MP 4K camera module with S-Mount lens holder and it has better low light performance. This small form factor 4K camera module is based on 1/3.2” AR1335 CMOS image sensor from ON Semiconductor® and has a dedicated, high-performance Image Signal Processor (ISP) that performs the entire Auto functions like auto white balance, auto exposure control in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression.
-
Product
Grypper "Y"
-
Ironwood Electronics Grypper Y contact is design to work with BGA devices with solder balls/bumps with no equator or small exposure where the standard Grypper cannot reliably hold on to the solder ball. The Y shape, working with the sliding lid, allows reliable contact and ensures device retention in high vibration application. Lower forces, <25 grams, makes insertion easier too and the less aggressive contacting allows 40+ insertions of the same device. The Sliding Lid can be configured to include heat sinking. The Y contact designs cover BGA devices from 0.35mm pitch and larger and the short electrical length has superior electrical performance.
-
Product
Vibration Meters
-
Companies must comply with the Control of Vibration at Work Regulations 2005 – this requires them to minimise and monitor exposure to hand-arm vibration and make sure that it does not exceed set levels and cause Hand Arm Vibration Syndrome. The best way to do this is by using a hand-arm vibration meter.
-
Product
Science-Grade MWIR InSb Camera
FLIR A6700 MWIR
-
Designed for electronics inspections, manufacturing monitoring, scientific research, and non-destructive testing, the FLIR A6700 MWIR camera is ideal for high-speed thermal events and fast-moving targets. Short exposure times allow users to freeze motion and achieve accurate temperature measurements. In fact, the camera’s image output can be windowed to increase frame rates to 480 frames per second to accurately characterize even higher speed thermal events, helping ensure critical data doesn’t get missed during testing.
-
Product
Adjustable Length Linear Backlight, 300 mm to 2100mm
Vitech A1905
-
Modules A1905 are designed for pulsed or continuous illumination of objects in machine vision systems. The time of ignition (90%) and blanking (10%) of the module is less than 1 μs with jitter of the front (jitter) no more than 2 μs, which allows the modules to be used for exposure with "slow" cameras.
-
Product
Magnetic Sensors
-
Magnetic proximity sensors are characterized by the possibility of large switching distances, available from sensors with small dimensions. They detect magnetic objects (usually permanent magnets), which are used to trigger the switching process. As the magnetic fields are able to pass through many non-magnetic materials, the switching process can also be triggered without the need for direct exposure to the target object. By using magnetic conductors (e.g., iron), the magnetic field can be transmitted over greater distances so that, for example, the signal can be carried away from high temperature areas.
-
Product
Rolling Shutter Image Sensors
-
Rolling Shutter devices start and then stop their exposure line by line. This means that that each line will be recorded at a slightly different exposure time. This effect is pronounced for short exposures which produces images with distortion due to moving objects and short flashes of light.
-
Product
Evaluation Services
-
Atlas Material Testing Solutions
Atlas offers a wide range of evaluation and measurement services for our client's specimens during and after the weathering process. These services are available at Atlas' Miami, Florida and Phoenix, Arizona sites. Atlas uses the most advanced instrumentation from leading manufacturers for measuring appearance properties such as color change, gloss, distinctness-of-image, transmittance and reflectance. All of our services meet the latest measurement test standards from organizations such as ASTM, ISO, DIN and others. A full range of visual assessment services is also available, including coating adhesion, blistering, chalking, cracking, mildew growth, and gray scale evaluation in accordance with respective standards' organizations. Temperature monitoring programs are provided for single and multiple specimens under any type of exposure, as well as for large assemblies such as complete vehicles. Strict quality control guidelines have enabled Atlas' Evaluations Laboratory to achieve industry-accepted accreditation from world renowned standards' organizations. Atlas is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) and accredited or approved by Ford, GM and AMECA.
-
Product
Dust Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sand Dust chamber provide an environment to test the exposure of automotive and electronic components to concentrated levels of dust in order to validate product seal integrity.
-
Product
5MP MIPI Camera Module
E-CAM55_CUMI0521_MOD
-
e-CAM55_CUMI0521_MOD is a small form factor, 5 MP fixed focus camera module based on AR0521 CMOS image sensor from ON Semiconductor® has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video. This low light camera module can stream uncompressed VGA (640 x 480) at 75 fps, HD (1280 x 720) at 100 fps, 1280 x 960 at 75 fps, FHD (1920 x 1080) at 65 fps, 2560 x 1440 at 38fps, 2592 x 1944 at 28 fps.
