-
Product
Analog Power Supply
Type NPS-2412
-
National RF's Type NPS-2412 analog power supply was designed to be used in communication equipment where radiated switching inverter noise from conventional “switching type” supplies is not acceptable. The power supply consists of a standard rectified transformer output driving a pair of voltage regulators and filtering networks. The 2412 offers an adjustable voltage output between 2 and 24 volts as well as a fixed voltage output of 12 volts. A maximum of 20 Watts of DC power can be supplied from the unit. As the voltage regulators dissipate power in the regulation process, the power to the load is derated accordingly, dependent on the set voltage to the load. The adjustable regulator is a standard LM-317T integrated circuit device. The fixed regulator is a standard LM 7812 device. Upon customer request, the LM 7812 device may be changed to any voltage rating within the the LM-78xx series of regulators. Contact National RF for this modification if desired.
-
Product
XCITE 1100 Field Test Series
-
The Xcite 1100 Field Test Series uses the same Exciter Heads and Master Controller as the 1100 Laboratory Series but replaces the 5 GPM 3-Phase Hydraulic Power Supply with a field portable 1.2 GPM Single Phase Power Supply. While providing the same 3000 PSI pressure, the field test unit is switch selectable from 110 V (20 A) to 220 V (10 A) single phase power.
-
Product
Battery Emulator And Profiler
E36731A
Battery Simulator
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
Product
Modular Redundant Power Supply Systems
-
Extremely high overall reliability results from connecting two power sources so that one will continue to provide power to their load even if the other becomes inoperative. Redundancy may be restored by replacing or repairing the inoperative source while the system remains in operation. A redundant power system should be used whenever the highest attainable reliability is essential, as in communications, computer systems (data storage in particular), process controls, utility and municipal systems, and security/safety systems.
-
Product
Advanced Power System: Dynamic DC Power Supply, 160 V, 12.5 A, 2000 W
N7977A
DC Power Supply
The N7977A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
Supervisory
-
Renesas voltage-monitoring supervisors combine competitive reset threshold accuracy and low power consumption to help monitor the power supply voltages in a wide variety of applications.
-
Product
Narrow Profile Power Supplies
AC-DC Wide Adjust Output
-
Power supplies with the broad adjustment capability required for analog instrumentation and circuitry, electronic system development, basic research, and similar applications.
-
Product
Regenerative Power System, 1000 V, ±60 A, 20 KW, 400/480 VAC
RP7972A
DC Power Supply
The RP7972A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
75-Watt AC/DC Power Supply; Triple Output
56KT1
Programmable Power Supply
NAI’s 56KT1 is a 75 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, triple output, at a baseplate temperature of +85° C.
-
Product
Power Supply Tester
UTS-325
-
UTS and STS systems are based on the Autotest A100 Instrument bus which provides a GPIB interface to load and source control and monitoring along with a measurement path matrix, timer/counter/trigger and peak detector instruments, user assignable relays and drivers.
-
Product
Power over Ethernet (PoE) DC/DC
-
An isolated 25W, PC/104-Plus form factor, 802.3af/at compliant, PoE PD power supply. The Class 4 signature supports up to twice the power of 802.3af compliant PD devices. Designed to power a single board computer from DC power extracted from a CAT5 cable sourced by an 802.3af/at compliant PSE device configured as either an endpoint or midspan device.
-
Product
4U CompactPCI Hybrid PlusIO System with 5 CompactPCI and 4 CPCI-S.0 Peripheral Slots
cPCIS-P2630R
Backplane
- 3U CompactPCI PlusIO backplane with five CompactPCI and four CPCI-S.0 peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports rear I/O backplane with P2 connectors for CompactPCI 50mm depth RTMs- Hot-swappable cooling fans & filter- 400 W ATX Power supply
-
Product
Passive Pulse Splitter
SY037
-
The SY037 passive pulse splitter is ideal for converting pulses from meters or other turbine devices and transmitting the same pulse to three outputs to enable three separate instruments to measure the rate simultaneously. It needs no power supply. It functions simply from the pulses of the meter driving it. It is convenient for meters and any pulse generating device with reed switches, open collector or current source.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
Ultra-High Stability DC Power Supply
62075H-30N
DC Power Supply
The 62075H-30N output power has maximum 7.5kW/30V/250A power module designed with 4U height that can be connected easily as master or slave with three units to 22.5kW/30V/750A in parallel or two units to 15kW/60V/250A in series and operated as a standalone unit via system bus. The 62075H-30N provides stable DC output cur rent sour ce and powe r for pre c i s ion measurement. It offers an advanced 250A/30V ultra high-stable ±10 ppm (current stability ±1.25 mA) with high eciency and high power factor in compliance with energy savings. In addition it has a 20 bit digital control with bright vacuum fluorescent display readout.
-
Product
Xilinx Kintex UltraScale SoM
TE0841
-
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TE0841 is an industrial-grade FPGA module integrating a Xilinx Kintex UltraScale KU35 or KU40 with 2x banks of 16-Bit width 512Mbtyes DDR4 SDRAM, max 256 MByte Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O’s is provided via rugged high-speed stacking connections.
-
Product
1kV, 80 MHz High Voltage Differential Probe with 6m Cable and Auto Zero Disconnect
HVD3106A-6M
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
LV Iron Core Harmonic Filters
-
Nonlinear loads such as power electronics based equipment and electric furnaces are sources of harmonic currents leading to harmonic distortion, which is one of the most important parameters for defining the power quality. Most of the commercial loads such as personal computers, photocopy machines, power supplies, and compact fluorescent lamps; and industrial loads such as AC and DC motor drives inject harmonic currents into the network that they are connected to.
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
Simulator
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Primary Metering
-
Is used when the utility is providing the customer power at medium voltage (5kV, 15kV, 25kV, and 35kV) rather than reducing the power supplied to the customer to low voltage.
-
Product
400W 6U CompactPCI Hot-Swappable Redundant Power Supply
cPS-H640/AC
Redundant Power Supply
- PICMG® 2.11 CompactPCI® Power Interface compliant- 6U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 400 W DC output
-
Product
19" Solid Fixed Storage Shelf, 24"D
SS-1924
-
Sturdy 19" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
Product
Combo Test Lead Kit
U8201A
-
Designed for use with U3606A DMM | DC power supply; includes leads, probes, alligator clips, SMT grabbers, and banana plugs
-
Product
MPOD HV Module
-
WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which can be mixed in type and parameters. Up to 480 individually controlled high voltage channels are available in one mainframe
-
Product
sbRIO-9253, Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module
787433-01
Current Input Module
Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module - The sbRIO-9253 is an 8-channel analog input module for CompactRIO Single-Board Controller that provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. This module includes diagnostic functionalities to ensure nominal system operations with open-channel detection, power supply detection, and configurable thresholds. You can view the status of each channel and the power supply with eight LEDs. The sbRIO-9253 also features programmable hardware filters for your applications, such as specific Butterworth and comb filters that you can use to reduce the noise in your system.
-
Product
T3 Low & High Voltage Differential Probes
T3 Series
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
Power Supply Testers
-
Qmax Test Technologies Pvt. Ltd.
Power Supply Tester is an integrated package of hardware such as AC/DC Power Sources, DC Loads, Noise Measurement Unit, and DMM etc configured as per user applications, which makes it suitable for testing wide range of Power Supplies and provide economic solution for testing AC/ DC and DC/DC power supplies and converters. The Power Supply Boards that passed in the first level of screening for Go-No Go tests will undergo a second level testing. The second level of testing measures all the key parameters of the power supply such as line regulation, load regulation, efficiency etc and check whether the results are within the mentioned limit, if not declare the UUT (Power Supply Board Under Test) as a failed one.
-
Product
High Voltage Film Capacitor
STHVP/STHVE
-
High Voltage Pulse Current for medium frequency applicationHigh Voltage DC / AC Voltage applicationCapacitor can be discharged at rated voltage directly without any protective component and with ambient Temperature up to +105CHigh Voltage Decoupling and SnubberingVoltage MultiplierInduction heatingAct as discharge capacitor to trigger laser, X-Ray and Tesla CoilFor high voltage capacitor bank or arrayHigh Voltage Power Supplies
-
Product
Advanced Power System - DC Power Supply, 120 V, 16.7 A, 2000 W
N6976A
DC Power Supply
The N6976A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Universal Multichannel System
-
Power Supply Systems are 100% internally developed and designed to install into a standard 19” relay rack. The mainframes and dedicated HV/LV boards were purposefully designed to provide peak performance in a broad spectrum of operational scenarios and for a vast number of detector types. CAEN mainframe systems are modular, making upgrade and maintenance a breeze.A single mainframe may house and provide control for up to 768 independent channels. Each mainframe may be configured with a mixture of both High Voltage boards for detector bias and Low Voltage boards to drive peripheral electronics.
