Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Signal Conditioning Modules
-
Signal conditioning modules provide signal conditioning on a per-module basis for various types of sensor or signal.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
HandyScope HS5 + SureConnect: 100 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 10MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-110XMS-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 100 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
PXI-6232, 16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Multifunction I/O Module
779618-01
Multifunction I/O
16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sourcing DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6232 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sourcing digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6232 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6232 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 12-Bank 6GHz SMA
60-801-012
Microwave Multiplexer
The 60-801-012 is a 6-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
NI-9476 / 779140-01
Digital Module
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V, based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
Product
Unified Satellite Phone Monitoring System
-
Unified Satellite Phone Monitoring System is designed to intercept Voice, SMS and Text traffic from Satellite Phones operating on Thuraya, Iridium and IsatPhone Pro Satellite networks. The system is pre-integrated & pre-configured in a compact ruggedized transportable casing for plug and play operations. It intercepts the signals from L-band uplink (from Satellite Phones to Satellites) and downlink (from Satellite to Satellite Phones) to provide the duplex calls up to 15 Kms with LOS and beyond that simplex calls. System is equipped state-of-the-art high performance Thuraya and IsatPhone Pro decryption module , Iridium proprietary protocol module to provide processed intelligible output in the form of Voice, SMS and Text along with session related information such as Called Phone Number (for session initiated by Satellite Phone),Caller ID, TMSI/IMSI/IMEI and geo-location
-
Product
4-CH 16-Bit 10/40 MS/s PCI Digitizers with 512 MB Memory
PCI-9816/9846
Digitizer
The ADLINK PCI-9816/9846 are 10MS/s, 40MS/s sampling 16-bit 4-CH digitizers designed for digitizing high frequency and wide dynamic range signals with an input frequency up to 20 MHz. The analog input range can be programmed via software to ±1 V or ±0.2 V and ±5 V or ±1 V. With a deep onboard acquisition memory up to 512 MB, the PCI-9816/PCI-9846 are not limited by the data transfer rate of the PCI bus to enable the recording of waveforms for extended periods of time.
-
Product
PXI Single 64 Chan 1 Pole MUX
40-657-001-1/64/1
Multiplexer Module
High Density Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
Line Injector
J2120A
-
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
-
Product
3 DB 90 Degree Hybrid Couplers
-
KRYTAR's 90 Degree Hybrid Couplers perform many functions, including splitting and combining signals in amplifiers, switching circuits, and antenna beam-forming networks used in a wide range of commercial and military applications. 90 degree hybrids are used in circuits requiring a balanced division of power into two transmission lines with 90 degree separation of phase.
-
Product
NI-9470, 5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module
787089-01
Digital Module
5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module - The NI‑9470 is a digital output module that features proportional valve drive control. You can use the NI-9470 to perform pulse width modulation (PWM), dither control, and current readback. The NI‑9470 features eight output channels compatible with signals from 5 V to 30 V and transient overvoltage protection between the output channels and the backplane.
-
Product
MULTI-STANDARD SIGNAL GENERATOR
VENTUS 2.0
-
Ventus 2.0 is a portable multi-standard signal generator operating with USB 2.0. It supports all common terrestrial broadcasting to satellite signals. Changing from one modulation to another is very easy with T-PUMP, included software.
-
Product
Power Dividers & Splitters
-
Keysight dividers and splitters are used in a wide range of applications, such as: transmission line fault testing, power combining, source leveling, ratio measurements, power splitting, and critical signal processing applications that require minimal insertion loss and high port isolation.
-
Product
Rotary Position Sensors -AEC- Q200 Compliant
-
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
Product
PXI Voltage Amplifier 10K Ohm, D Type
41-650-011
Amplifier
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
Product
Float Switches
-
B/W Controls has been manufacturing float based tilt switches for decades. Simple tilt position is all that is needed to actuate a B/W relay and or signal a control panel of the alarm.
-
Product
Cellular Signal Analysers
SNYPER Family
-
2G, 3G and 4G LTE cellular signal analyser range - including Spectrum 'livescan'. The SNYPER is a sophisticated yet easy to use range of cellular signal analyser comprising 2G and 3G versions with LTE family Now available.
-
Product
CATV Return Band Two Carrier Generator
PC-2
-
The PC-2 is a compact, temperature-stable two RF-carrier source. It is designed to be used for activating and testing the return-band. When used with a signal level meter, the PC-2 assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.
-
Product
Transceiver
-
A device which receives an electrical digital signal, converts it into an optical signal, and transmits it into the fiber or vice versa. Optical transceiver is a standard device in optical communication system.
-
Product
FieldFox Handheld Microwave Signal Analyzer, 50 GHz
N9962B
Signal Analyzer
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
Oscilloscope
2542C-MSO
-
The 2540C Digital Storage and Mixed Signal Oscilloscope (MSO) Series delivers advanced features and debug capabilities for a wide range of applications at an entry-level price point. With up to 200 MHz bandwidth in a 2-channel configuration, each model offers a maximum sample rate of 1 GSa/s, and a maximum memory depth of 14 Mpts. In addition, these oscilloscopes provide an 8” color display with 256 levels of color grading combined with a high waveform update rate up to 60,000 wfms/s, which allows the instruments to capture infrequent glitches with excellent signal fidelity.
-
Product
Signal Conditioners / OEM Boards
-
Signal conditioners and OEM cards that can be integrated into your system.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 7-Bank 6GHz SMA
60-801-007
Multiplexer Module
The 60-801-007 is a 6-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
USB-5132, 50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device
780468-02
Oscilloscope
50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5132 low-cost oscilloscope device has two channels that sample up to 50 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
Product
Automotive Tablet Oscilloscope
SATO1000 series
-
Shenzhen Micsig Instruments Co., Ltd.
*8-inch TFT-LCD capacitive touch screen with 800 * 600 resolution, interagtes a new generation of hardware & software technologies*High bandwidth, High sampling rate, Large memory depth, excellent signal capture performance
-
Product
Mass Interconnect
-
Mass interconnect is a way of connecting test instrumentation to a device under test (DUT). To put it simply, mass interconnect is a very large plug and socket which connects your device under test to your test instrumentation without the mess and hassle of having to connect each signal separately.
-
Product
Car-to-X Test Bench
-
Qosmotec Software Solutions GmbH
The QPER-C2X adaptation, that emulates signal strength between radio devices for Car-to-X communication in the lab, can be combined with the test automation software CANoe from Vector Informatik to enable a fully automated lab test under realistic radio conditions. This combination can be regarded as full test bench setups for Car-to-X test laboratories.
-
Product
8-bank, 16-channel, 1 Pole Version is part of the 40-614C High Density 2A Multiplexer Module
40-614C-003
Multiplexer Module
This 8-bank, 16-channel, 1 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
783908-01
Digital Module
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
