Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
1 GHz, 2 Analog Channels Oscilloscope
DSOX3102A
Oscilloscope
1 GHz2 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Oscilloscope - 1 GHz, 4 Analog Channels
DSOX3104T
Oscilloscope
1 GHz4 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
ESPI Analysis Application
TP601010
-
First released by Intel in June 2013, the Enhanced Serial Peripheral Interface (“eSPI”) is designed as a replacement for the Low Pin Count (“LPC”) bus. eSPI supports communication between Embedded Controller (EC), Baseboard Management Controller (BMC), Super-I/O (SIO) and Port-80 debug cards. eSPI was available in the Sky Lake chipset (2015) and is available in the Kaby Lake [current] chipset. Cannonlake will support eSPI and is slated for release the second half of 2017. Icelake is scheduled for release in 2019 and it will mark the first chipset when eSPI becomes mandatory.
-
Product
Windows Managed Client/Server Software For BACnet Systems
CBQ
-
CBQ is implemented as a managed .NET 64 bit DLL. The DLL works with BACnet/IPv4 and BACnet/IPv6 over Ethernet, and you can even use MS/TP through USB or any standard serial COM port, with an external EIA-485 converter. Our famous MS/TP for Windows technology is unequalled and provides fast, reliable operation with direct connection to EIA-485 networks.
-
Product
ARM LPC2468 Board
MS 1511
-
- 32 Bit ARM7 LPC2468 Processor (128KB SRAM, 512KB FLASH)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports- High Speed Logic Device- External Bus Interface (15 bit address bus and 16 bit data bus)
-
Product
Conduction Cooled XMC Interface Board with PCI Express Host Interface, Supporting up to 4 PX Modules, 2 RTx 5 Channel Modules, 1 Discrete & 1 Serial Module
EXC-8000ccXMC
-
The EXC-8000ccXMC is part of Excalibur’s 8000 family of multiprotocol boards. This conduction cooled XMC interface board has a PCI Express host interface and supports up to 4 Px modules, 2 RTx 5 channel modules, 1 Discrete and 1 Serial module. Due to the constraints of the XMC specification the modules are integrated onto the board itself rather than as physically separate modules.The EXC-8000ccXMC supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from modules that support DMA, with much less CPU overhead than when not using DMA.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - XMC
Model 71610
-
- 32 bits of LVDS digital I/O- One LVDS clock- One LVDS data valid- One LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAs- DMA controller moves data to and from system memory- Up to 2 GB of DDR3 SDRAM- PCI Express Interface- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- RoHS Compliant Lead-Free Version Available
-
Product
Mixed Signal Oscilloscope, 500 MHz 2 Analog Plus 16 Digital Channels
MSOX3052A
Oscilloscope
500 MHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
3U CompactPCI Serial 9th Gen Intel Xeon®/Core™ i7 Processor Blade
cPCI-A3525 Series
Processor Blade
CompactPCI® Serial (PICMG CPCI-S.0) is a new modular computer standard officially adopted by PICMG in 2011. The CompactPCI Serial standard defines a completely new connector to support high-speed serial interfaces including PCI Express, SATA, USB and Ethernet. A CompactPCI Serial backplane has six high-speed connectors P1 to P6 on the system slot but only P1 is mandatory on peripheral slots, P2 to P6 being optional. A CompactPCI Serial system can comprise a total of nine blades (one system blade and eight peripheral I/O blades) through an Ethernet full mesh or single star architecture. The CompactPCI® Serial standard is the next-generation of the CompactPCI® specification and provides more flexibility and higher speed and bandwidth in modular system solutions.
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX4032A
Oscilloscope
350 MHz2 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
10-Pin RJ50 Male to 9-Pin D-SUB Male Serial Cable
182845-01
Serial Cable
S8 Serial Cable, 10Pos Modular Plug to DB-9, 1 m (non isolated)
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-7 FPGA - 6U VPX
Model 57720
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- One or two DUCs (Digital Upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connectionsto the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Intel 80486 DX2 Processor Board
MS 1500
-
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
Product
64 Channel Digital Output and 4 Channel RS422 Module
DP-OBC-3006
-
DP-OBC-3006 is a 3U cPCI-based board with 64 Digital Output channels and 4 ports of RS422 serial interface. It has 64 digital output channels in open/ground configuration and operates on 32-bit, 33MHz PCI bus. Four RS422 channels are incorporated with opto-isolated inputs which supports baud rates upto 115. Kbps.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Bench Digital Multimeter, Calibrated, Data, 1 kV, 10 A, 3.8 Digit
72-1015 CAL D
-
The 72-1015 CAL D from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
PXI Single 36 Channel MUX, SMB Connectors
40-735-912-S4
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
HPLC Pumps
MX Class
-
Further applications include demanding metering and dispensing, as well as Sample Injection, Infusion, or Cone Wash for Mass Spectrometers. Standard fluid path material is Stainless Steel. With flow rates up to 10 mL/min, these pumps can tackle the majority of demanding laboratory applications.Features include pressure monitoring with automatic pressure compensation, Pulse Dampener, integrated Prime-Purge Valve, interactive keypad control, and complete PC control and status through RS-232, micro-USB 2.0, and Ethernet serial communications. Requiring minimal bench space for the performance, the MX Class will easily integrate into most workspaces.
-
Product
WAV Trigger
-
The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the WAV Trigger can play and mix up to 14 stereo tracks simultaneously and independently, with very low latency. Tracks can be controlled via 16 programmable trigger inputs, or by using a native serial control protocol or even MIDI.
-
Product
USB-COM Data Logger
-
The USB-COM Utility is a free data logging andconfiguration program for use with the Validyneseries of USB or Serial pressure transducers.USB-COM Utility also comes in a premiumversion that allows up to eight signals to begraphed simultaneously while being recorded toa .csv file. The graph X and Y axis may bescaled to any values set by the user. A separatehistorical graph provides a complete visualrecord of the signals from the start of logging.
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
Serial to Parallel Controller
E84 SPC
-
300mm equipment manufacturers utilize this off-the-shelf E84 communications controller to provide SEMI E84 compliant communications for their products. With its built-in Load and Unload algorithms it is the perfect E84 communications solution for process tools, stockers, load ports, FOUP buffers, smart storage shelves and simulation load ports. The E84 SPC easily integrates with equipment controllers through a standard serial communications connection.
-
Product
Advanced ISP programmer
IS01
-
IS01 is a multi-function, high-speed professional universal ISP programmer. It supports almost all kinds of serial programmable devices.
-
Product
Control Unit
Epec 3610
-
Epec 3610 Control Unit is a compact controller containing 22 I/O pins, all of them can be configured as input pins. Epec 3610 has an RS-232 serial port and as an assembly variant, I/O interface that is compatible with the previous Epec 2038 Control Unit. However, Epec 3610 also comes with completely new features like high-side current measurement and an internal 3-axis accelerometer, for example, for levelling purposes. Epec 3610 also has an option for accurate Pt1000 measurement.
-
Product
High Speed Thermal Printer
6041
-
• RS232C serial interface via a 6-pole RJ12 socket• Tested to comply with FCC Standards• Designed for use with Associated Model 6044 and similar devices• Four AA Batteries included• Imported
-
Product
Modbus or Laurel ASCII ProtocolSerial Output DIN Rail Transmitters
-
Laureate TM Series serial output transmitters can be jumpered for two signal levels: RS232 or RS485. Two serial protocols are selectable in software: Modbus or Laurel's Custom ASCII.Modbus protocol operation is fully compliant with the Modbus Over Serial Line Specification V1.0 (2002) for 2-wire, half-duplex connection.
-
Product
Serial Production Mark Quality Control
-
The control system is based on the Sick IVC smart camera, which not only captures, but also processes the image. After training on the font samples, the system practically does not require the operator's attention in addition to setting the current marking for control. The character set can be specified by the operator or transmitted via the interface from the printer or from the enterprise information system.The camera software works autonomously: it loads all settings from the camera's permanent memory, initializes the backlight electronics and waits for a signal from the object presence sensor. When a signal is received from the sensor (an object in the shooting area), the camera captures the frame, searches for markings and analyzes the symbols for their compliance with the exemplary set.
-
Product
PXIe Modular Oscilloscopes
M924XA
Oscilloscope
200 MHz, 500 MHz and 1 GHz bandwidths2 analog channels and 5 GSa/s sample rate See more signal detail with 1,000,000 wfms/s update rate Quickly isolate signals with zone triggering Also available: 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger/analysis and mask testing
-
Product
PCI Express Multi-Function Boards
PCIe-S142i
-
PCI Express, Serial Communication Board with 2 Isolated RS-422/485 ports
-
Product
Intelligent Digital Multimeter, Calibrated, 3999 Count, Mean Value, Auto, Manual Range, 3.75 Digit
72-7755 CAL
-
The 72-7755 CAL from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
