Discrete Component Testers
check connected individual semiconductor components.
-
Product
Simulating Optical Design Components
Wave Optics Module
-
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
Discrete Input Event Recorder
-
Wabtec M Series Recorders provide a compact recording solution for discrete electrical and pneumatic signals and provide compliance to FRA Crash Hardening requirements.
-
Product
IPD RF Components – LTCC
-
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Passive Components
-
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
-
Product
LCR Component Meter with Component Impedance Measurement
LCR45
-
The new LCR45 does everything that the popular LCR40 does, but we've added some significant enhancements. The LCR45 features a new high capacity micro and high resolution ADCs.*Fluid measurements of L, C and R (continuous readings with selectable hold function).*Fine resolution for improved performance at low inductance/capacitance/resistance.*Auto and Manual component type.*Auto and Manual test frequency.*Frequencies: DC, 1kHz, 15kHz and 200kHz.*Display of component values, complex impedance, complex admittance and magnitude/phase.
-
Product
Coaxial Components
-
Surge arrestors are designed to protect wireless base stations, switching centers and transmission lines fromthe damaging effects of extreme high voltage surges caused by lightning strikes. The RFS lightning protectiondevices are designed and tested to the most demanding specifications. They are rated to protect against bothdirect and indirect multiple strikes in the harshest environments imaginable. Their rugged construction utilizes solid metal housing, and superior plating, which results in outstanding system protection and operatingcontinuity.
-
Product
Passive Components
-
Narrow and broadband, tailored cut-off frequencies and slope, electronically controllable, high-Q factor, highly linear transfer characteristics
-
Product
Radiation Hardened Solutions and High Reliability Components
-
Offering a complete portfolio of RadHard and HiRel components, CAES serves as the foundation on which many critical applications are built.
-
Product
Measurement Components
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Innovative developments and modern electronic applications to support everyday life require the use of ever higher frequencies – this applies to specialized areas such as aerospace technology and automotive as well as to the increasing bandwidth requirements in communications technology.
-
-
Product
Lens Driver Components
-
Analog Devices offers a range of lens driver solutions for camera modules in camera phones, camera enabled handsets, DSCs, consumer entertainment, and computer imaging. Lens drivers integrate drivers, waveform control, power management, signal processing, travel control, and more to provide the smallest, lowest power, most complete system solutions with the latest motor/actuator technologies.
-
Product
16-CH Discrete Input 16-CH Discrete Output Module with UJ Type Connector
HSL-DI16DO16-UJ
Input/Output Module
*16-CH digital input and 16-CH digital output*Higher output current up to 90mA/channel*Isolation Voltage: 2500Vrms*JAE 3-pin connector*Easy installation and wiring
-
Product
RTM Analog & Discrete Signal Conditioning Board
-
CPCI Rear IO Analog and Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3663i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector. And Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector
-
Product
Components - Passive Multipliers (FT)
FT Series
-
Farran Technology manufactures a series of standard frequency multipliers which are available in fixed or tunable versions. GaAs Schottky barrier varactors are used to achieve the highest efficiency. The multipliers can be used with solid state or vacuum tube sources. A rugged compact mechanical design is used to maximise reliability.
-
Product
Protective Cover, 9050, VXI and Discrete Wiring, ITA
410114298
Protective Cover
Protective Cover, 9050, VXI and Discrete Wiring, ITA.
-
Product
ITA, 9050, 50 Module, VXI And Discrete Wiring, VDATS
410104721
ITA
Customized VDATS 9050 VXI ITA frame with 3 bearings per side.
-
Product
68-Pin SCSI Micro-D Male Discrete Wire
40-962-068-M
SCSI Male Connector
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Wound Component EST Analyzer
19036
Analyzer
Chroma 19036 is the industry's first wound component electrical safety test (EST) analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
Product
Embedded Components
-
Teledyne Labtech prides itself in being at the forefront of RF/Microwave PCB development. Teledyne Labtech were also one of the first companies to successfully develop techniques for embedding SMD resistors and capacitors within multilayer structures and the embedding of connector pins in buried stripline circuits.The advantages of such a structures ensures a much higher density of interconnect. This then removes the need for via-hole connections to the board surface or the need to create access pockets to the inner layers. Consequently you finish with a board with that exhibits much lower RF/Microwave losses. This is particularly important when designing large RF feed networks or 16:1 power dividers.
-
Product
Components - Power Amplifiers (FPA)
FPA Series
-
FPA series driver amplifiers and power amplifiers are discrete and/or MMIC pHEMT device-based amplifiers that operate over the frequency range 18 to 110 GHz for high output power applications. The amplifiers are offered in two categories, standard and custom built up to 250 GHz.The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration. The optional input and output integrated isolators are available to further improve the port return loss.
-
Product
High Mix High Component Count Or LED Panels
MC388
-
The MC388 features four simultaneous heads with dual-vision alignment that can achieve placement rates of 10,500 CPH. When used as an inline machine, up to 192 Smart Feeder can be attached, providing a near-zero job changeover time. Plus, it has the huge placement area, high precision, and accuracy that users have come to expect from MC-series component placers. The MC388 is ideal for LED strips, drivers, or other large, high-component panels.
-
Product
PXI Vector Component Analyzer, 100 kHz to 53 GHz
M9818AS
Vector Component Analyzer
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
Product
PRECISION COMPONENT ANALYZER
6400 SERIES
-
The 6430B and 6440B Precision Component Analyzers provide thorough and accurate testing of any passive component to high resolution. In particular, for capacitor manufacturers, the instruments provide capabilities for both fast automatic production testing and complete design characterisation. Users include designers of passive components, manufacturing test, designing and testing materials as well as circuit designers who are evaluating component characteristics.
-
Product
RF/Microwave Components and Integrated Microwave Subsystems
-
PIN Diode Switches, PIN Attenuators, PIN Limiters, Video Products, Switching Assemblies, Integrated Subsystems
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
Digital Input Module
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
Complete Set of React Components
ExtReact
-
Building React components on your own is time consuming, has integration and maintenance risks, and gets in the way of actually building the app. Now you can easily get all of the components you need to build data-intensive web apps with ExtReact. To learn more, read the FAQ and try ExtReact in a browser with Sencha Fiddle.
-
Product
Optical Modules And Components
-
Luna offers a complete line of high performance active and passive fiber optic modules and components for a wide range of fiber optic systems, including interferometric systems for fiber optics sensing, fiber optic gyroscope (FOG) and optical coherence tomography (OCT).
-
Product
Passive Components
-
VDI offers a wide variety of waveguide sections, tapers, antennae, bends, and directional couplers for your application. Please note that external dimensions are subject to change.
