-
product
2-Ch 1 GHz A/D and D/A with Virtex-7 FPGA - 6U VPX
Model 58730
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1 GHz 12-bit A/D- One or two 1 GHz 16-bit D/A- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Relay And Protection Testing
As the first protection relay test set manufacturer in China, PONOVO has been always offering reliable protection relay testing equipment for customer for more than 20 years. More than 20,000 relay test kits has been supplied to users in China and other countries, including 6-phase, 3-phase, single phase relay test sets, capable of testing all kinds of protection relays, from electromagnetic relays, solid state, numerical, microcomputer relays and digital relays based on IEC61850 as well as other testings, such as, energy meter, transducer, etc. With various models with different specifications, users can definitely choose the model suitable for their testings.
-
product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.25 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2223-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Virtual Optical Power and Energy Meter
844-PE-USB
The Model 844-PE-USB is a Power Meter with a USB connection to use a computer as the monitor, allowing the user to access the full computing power of the computer.
-
product
Programmable Switching DC Power Supply
SPS5000X Series
The SPS5000X-Series is a programmable Switching DC Power supply series that provides a wide range of output power using single-channel and multi-channel output configurations coupled with constant power capability. The series of power supplies includes sixteen models with voltages to 160 VDC and power to 1080 W. The SPS5000X supplies can be connected in series (2 units) or in parallel (3 units) to meet the requirements of 0~320V and 0~270A, with a maximum combined power of 3240W.
-
product
Simulink models run on ADwin
ADsim
With ADsim, you easily run Simulink models on ADwin hardware. With a few clicks only, you insert inputs and outputs for the ADwin system as blocks into the model and start C code generation. After compilation, the model runs on the ADwin system in real-time with absolute timing precision and predictability reaching sample rates up to 100 kHz.
-
product
Terminations And Mismatch Loads
JFW’s online 50 Ohm Low power termination and mismatch load models are listed in the table below. JFW has been designing, manufacturing, and delivering quality terminations and mismatch loads for over 30 years. Our mismatch loads allow you to select the impedance mismatch your RF testing requires.
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - XMC
Model 71851
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex Ultrascale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the Kintex - Ultrascale FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Microwave Testing
220
The PICOPROBE® MODEL 220, a high performance microwave probe which incorporates a WR-5 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
product
Industrial Design
Altair’s industrial design tools allow designers, architects, and digital artists to create, evaluate, and visualize their vision faster than ever before. Focus on ideas instead of being hindered by shortcomings of the software tools and liberate creativity with design software that lets the user model freely, make changes effortlessly, and render beautifully.
-
product
Ultrasonic Thickness Gauge
QTG Series
Ultrasonic Thickness Gauge - QTG Series are economical, user-friendly, menu driven, and multi-functional units offering extensive features from basic measurements (model: QTG I) to extended memory (5000 reading storage) and USB output capabilities (model QTG II). The instrument can measure with very high resolution (0.01 mm or 0.001 inches) the thickness of metallic and non-metallic materials such as steel, aluminum, titanium, plastics, ceramics, glass and any other good ultrasonic wave conductor. The Ultrasonic Thickness Gauge - QTG Series accurately displays readings in either inches or millimeters and is equipped with special features like Automatic recognition of probes with different frequencies and Automatic zeroing of the unit.
-
product
PCI Data Acquisition Boards
ADDA12-100DMA Series - Dual 12-bit A/D + Dual 14-bit D/A, 25 Ms/s
Model ADDA12-100DMA has two simultaneously sampling 12-bit A/D converters, two 14-bit D/A converters, five vectored TTL inputs and two vectored TTL outputs, and is able to transfer data directly into the computer system's memory at 100 MB/s in systems with 64-bit PCI slots or 80 MB/s in 32-bit slots.
-
product
RF Shielded Box
LTL A4001
Liveon Technolabs LTL A4001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A4001 RF shielded test enclosure can comfortably house the intermediate device on test. LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
product
Open Source Computer Vision & Machine Learning Software Library
OpenCV
Open Source Computer Vision Library
The library has more than 2500 optimized algorithms, which includes a comprehensive set of both classic and state-of-the-art computer vision and machine learning algorithms. These algorithms can be used to detect and recognize faces, identify objects, classify human actions in videos, track camera movements, track moving objects, extract 3D models of objects, produce 3D point clouds from stereo cameras, stitch images together to produce a high resolution image of an entire scene, find similar images from an image database, remove red eyes from images taken using flash, follow eye movements, recognize scenery and establish markers to overlay it with augmented reality, etc.
-
product
Pulse Characterization Sensors
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
product
PXI 2x SPST Power Relay, 2 Slot
40-170-001
Model 40-170 is available either as 2 x SPST High Power Relays, suitable for switching inductive/ capacitive loads up to 30A at 250VAC or as 2 x DPST switching up to 20A. Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
33 GHz Optical Probe
DPO7OE1
The DPO7OE1 is a 33 GHz, low noise, broad wavelength optical probe with optical reference receiver (ORR) performance for 28Gbaud PAM4 and PAM2 (NRZ). The DPO7OE1 can be used as a conventional Optical-to-Electrical (O/E) converter for wide-bandwidth optical signal acquisition. The DPO7OE1 provides an FC/PC or FC/APC optical connection for Tektronix DPO/MSO70000 C/DX/SX model oscilloscopes for high-speed optical signal verification.
-
product
DHCP Tests
The Dynamic Host Configuration Protocol (DHCP) provides configuration parameters to Internet hosts. DHCP consists of two components: a protocol for delivering host-specific configuration parameters from a DHCP server to a host and a mechanism for allocation of network addresses to hosts. DHCP is built on a client-server model, where designated DHCP server hosts allocate network addresses and deliver configuration parameters to dynamically configured hosts. (Source: RFC 2131)
-
product
CDNs
In addition to a range of 'conventional' CDNs, Laplace are unique in offering two other types. Both types are 'versatile' in that they are configurable, offering great flexibility in terms of the type of cable each model can be used with. This reduces the number of CDNs necessary to hold in stock. The final type is, in addition to being versatile, fitted with an output which monitors the RF level applied to the cable.
-
product
Potable Coordinate Measuring Machines
Romer
A first in the world of portable measuring arms: The ROMER Absolute Arm features absolute encoders and is therefore the first measuring arm which does not require referencing before measurement. When the arm is turned on, it’s ready to go.Quality control, inspection, on-machine verification, reverse engineering, virtual assembly or 3D modelling. Wherever these needs arise, you will find the ROMER Absolute Arm. Much more than just a metrology tool, its value lies in its versatility.Portability, stability, light weight and high-performance laser scanners make the ROMER Absolute Arm an all-purpose 3D measurement, analysis and digitising tool that can be used by anyone, anywhere and with minimum training.Unlike many metrology devices, the ROMER Absolute Arm does not require warm-up time or initialization, thanks to a stable carbon fiber structure and industry leading Absolute encoders. Simply take the measuring arm to the part, switch it on and start measuring.
-
product
Universal Hardness Tester
A great advantage for testing labs is combining different test methods in one Universal hardness tester, which allows significant cost and space savings, flexibility and user-friendliness. Qualitest offers a competitive range of dead-weight models up to best selling load-cell type systems. These Universal hardness testers can cover Rockwell Regular, Superficial as well as Brinell and Vickers scales in one single machine.
-
product
mA Loop Calibrators
Loop Calibrators are indispensable tools for process calibration professionals and we have just one you need. Choose from three different models depending on your need for accuracy and intrinsic safety. Each one is feature-rich and simple to operate and read.
-
product
ICP® Shock Accelerometers
Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.
-
product
Easy E23 / E84
Objective Solutions' Easy E23/E84 product line is designed to simplify the integration of SEMI E84 and E23 into Process Equipment and Factory Vehicle systems. The models provide a standard E23/E84 infrared interface to AGV/OHV and process equipment, utilizing Hokuyo transceivers. The Easy E23/E84 units have been developed to work as-is with Hokuyo IR transceivers and as an option, with opti-isolation as required by direct-connect applications. They enable simple integration to process equipment or AGV application programs.
-
product
Cinema Surround Loudspeakers
HMS
Designed to complement Meyer Sound’s Acheron screen channel loudspeakers, the self-powered HMS maintains a wide dynamic range, exceptional fidelity, and precise clarity during the most demanding of digital soundtracks. It is available in four models: HMS-5, HMS-10, HMS-12, and HMS-15, ranging in size, weight, driver size, and power to accommodate a wide range of venues and applications.
-
product
DCDC
QQA Series
The QQA series features the latest in MOSFET design, state of the art surface mount technology, and offers a 4:1 ultra-wide input range, and efficiencies greater than 80% (typ). Features include continuous short circuit protection, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. All models are packaged in a six-sided shielded miniature case measuring only 1.0” x 2.0” x 0.4” high.
-
product
Ruggedized Laser Distance Meter with Compass
TRUPULSE 360R
F. W. Breithaupt & Sohn GmbH & Co.KG
*Scope magnification 7-times*Field of view 100m/915m distance*LCD Display*Range to non-reflecting targets 1.000m*Range to reflecting targets 2.000m*Accuracy in range ± 30cm (± 1m to weak targets; shown in display)*Accuracy in slope ± 0,25°*TruVector Compass Technology*Accuracy of compass ± 1° typical*RS 232/Serial interface (Model B: with Bluetooth)*IP protection IP56
-
product
16 Channel Multievent Peak Sensing ADC
V785N
The Model V785N is a 1-unit wide VME 6U module housing 16 Peak Sensing Analog-to-Digital Conversion channels. Each channel is able to detect and convert the peak value of the positive analog signals (with >50 ns risetime) fed to the relevant connectors. Input voltage range is 0 ÷ 4 V. The Mod. V785 N features LEMO 00 connectors for both input and control signals.
-
product
40W to 65W - Single Output
CSW Series
*Accepts 115/230/277 VAC Nominal Inputs*DIN Rail Mount Option*Global Safety Agency Compliance*<150mW Off-Load Power Consumption*DOE Efficiency Level VI, ErP Tier 2*UL 1310 Class 2 Compliant (24V Model)
-
product
1 GHz A/D and D/A with Virtex-7 FPGA - XMC
Model 71730
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual uSync clock/sync for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
