System Under Test
tries inter, extra and intra interoperability. Also known as: SUT
See Also: EUT, Unit Under Test, UUT
-
Product
Meter Test System
MTS-100
-
Kongter Test & Measurement Co., Limited
This Meter Test System features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 120A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
High Voltage Test System
CKT1175-15
-
12.5 mV – 2000 VDCIR measurements to 5000 megohmsHipot testingDwell time prog. from 1 ms to 1000s in 1 ms steps
-
Product
LED Driver Automatic Test System
ATE-2
-
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
-
Product
Test Systems & Sub-systems Development and Integration
-
Research, development and the production of electronic test equipment, systems and subsystems for the industrial, scientific, and defense markets.
-
Product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
System
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
Product
USB PD Test System
6050
-
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
Product
In-System Test Programming System
WriteNow
-
Based on proprietary WriteNow! Technology, the WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices from various manufacturers and have a compact size for easy ATE/fixture integration. They work standalone or connected to a host PC, and are provided with easy-to-use software utilities.
-
Product
Incircuit and Functional Test Systems
-
REINHARDT System- und Messelectronic GmbH
We offer test systems which vary in their expansion and can be used for different ranges of automatic testing.
-
Product
Camera Test System
FS 8681 / SR
-
FS8681/SR is software for evaluating images* and making pass/fail judgments in camera mass production inspections. It consists of the "Editor FS8681" application that sets the inspection content and the "Sequence Runner FS8681SR" application that executes the set inspection.
-
Product
TD-SCDMA Analysis Using NI PXI RF Test Instruments
NI-RFmx TD-SCDMA
Test Instrument
The NI-RFmx TD-SCDMA personality is a highly optimized API for performing physical layer measurements on TD-SCDMA cellular standard signals. NI-RFmx TD-SCDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
Product
802.11ad & ay (WiGig) Test System
IQgig-IF
-
When used in conjunction with IQgig-RF, it supports over-the-air (OTA) testing of WiGig RF modules and end-products. The IQgig family products provide total test solution for R&D characterization and high volume manufacturing.
-
Product
Test System
-
Maynuo Electronic Co.,Ltd a professional R & D and production of programmable DC electronic loads, programmable DC power supply, high power load, power supply, AC power supply, power supply, such as testing high-performance mobile phone test equipment and facilities, as well as electrical, electronic, aerospace, military, chemical, automotive, battery charger, battery, solar cell production lines and other industries to provide automated testing program. The company has many years experience in a number of outstanding technical R & D, product innovation by the majority of users. We are committed to provide users with more accurate and more stable more easily accessible to the higher cost of test instruments, to create the industry in testing the influence of an international brand of excellence.
-
Product
Battery & Electrical System Testing
12-0200
-
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
Product
V4 Marine Communications System - V4 NAVTEX Test System
-
The ICS Electronics Limited V4 NAVTEX Test system may be used for type approval, general performance testing and production testing of NAVTEX receivers.
-
Product
Fully Automatic Tensile Testing System
-
This is a fully automatic tensile testing system for metals. The system is fully automated from supply of specimens, measurement of specimens, tensile testing, recovery of specimens, and data processing, and is capable of continuous nighttime testing.
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
Three-phase Fully Automatic Test System
TS41
-
Calmet Smart Calibration Devices
The Calmet TS41 test system consists of a three-phase reference meter of accuracy class 0.02% (or 0.04%) and an integrated three-phase current and voltage source up to 3x120A/600V. It makes possible automatic testing of electricity meters in meter test stations
-
-
Product
Cable Test Vans and Systems
-
Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.
-
Product
Electro-Stimulation Equipment Testing System
STIMU-600
-
Test device for functional testing of electrical stimulation devices.
-
Product
DC Hysteresis Graph Test System
DX-2012H
-
Automatic measurement of the demagnetization curve of permanent magnetic material such as ferrite, AlNiCo, NdFeB, SmCo, etc. Accurate measurement of the magnetic characteristic parameters of remanence Br, coercive force HcB, intrinsic coercive force HcJ and maximum magnetic energy product (BH)max.
-
Product
ATE & Test Systems
-
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
Product
Semiconductor Test System
-
IST Information Scan Technology, Inc.
As power modules age, their performance degrades. Proper testing and maintenance of semiconductor devices used in power switching can ensure optimal performance and prevent down-time throughout a device’s lifecycle. The IST Model 8900 Series Discrete Semiconductor Test Systems allows you to effectively identify the percent of degradation in semiconductor devices by simulating the exact current and voltage of the parameters used by devices under real operating conditions.
-
Product
PXI System for LRU Test
ARINC 629
-
PXI System for LRU Test Support. The system shown here was developed in support of Boeing 777 LRU Production Test.
-
Product
Test System Mainframe
ITC59000
-
The ITC59000 Test Platform is a desktop DynamicParametric Test System mainframe. The ITC59000Test Platform accepts up to four Test MeasurementUnits (TMUs) that perform transient measurements onsemiconductor devices such as power MOSFETs,IGBTs, and diodes.
-
Product
Engine Performance/Endurance Test System
-
Various types of test system as follows can be built up in combination with measurement control equipment and peripheral instruments (fuel flow meters, actuators, temperature control device, combustion analysis system, ECU monitor, OBD, sound and vibration measurement instruments, emission analyzer, smoke meter etc.)·Traveling fuel economy test·Gas emission test·Output performance test·Deterioration/endurance test·Combustion analysis·Sound source probing
-
Product
Full Wafer Test System
FOX-1P
-
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
Product
Portable Meter Site Test System
Bantam Plus
-
The Bantam Plus is the newest and most technologically advanced portable three-phase meter site test solution available for today’s metering professional. This innovative solution supplies a safe, accurate and highly versatile answer to the diverse test requirements of today’s electric metering.
