System Under Test
tries inter, extra and intra interoperability. Also known as: SUT
See Also: EUT, Unit Under Test, UUT
-
product
Vibration Test System
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Vibration Test System is a simulation of the various environments encountered in the manufacturing, assembly, transportation and use phases of execution. It is primarily used to identify the ability of a product to withstand environmental vibrations.
-
product
DWV/IR Test Systems
When used in conjunction with ART's own parametric relay test systems such as the RT290, the RT900 offers high speed AC and DC Hipot (dielectric withstand voltage) and Leakage testing of relays or other multi-pin passive devices.
-
product
High Voltage Cable/Harness Test System
CKT1175-50
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
product
Thermal Stability Test System
Premier Electrosystems' Thermal Stability Test Setup is used to test thermoplastics and PVC (Plasticized Polyvinyl Chloride) materials. When exposed to continuous heat, these materials degenerate and emit harmful acidic gases. The instrument is manufactured for testing PVC materials for their thermal stability at higher temperature.
-
product
Incircuit and Functional Test Systems
REINHARDT System- und Messelectronic GmbH
We offer test systems which vary in their expansion and can be used for different ranges of automatic testing.
-
product
RF Conducted Immunity Test System
RFCI61000-4-6
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Rail Traction Inverter Test System
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.
-
product
PXI System for LRU Test
ARINC 629
PXI System for LRU Test Support. The system shown here was developed in support of Boeing 777 LRU Production Test.
-
product
SSD Test System
The Neosem’s SSD test system combines advanced SSDtest hardware, software and environmental chamber into a single platform and supports all popular storage interfaces including PCIe, SAS & SATA and fast emerging protocols such as NVMe and AHCI.
-
product
LED Power Driver Test System
Chroma C8000
Chroma Systems Solutions, Inc.
The Chroma 8491 ATS is equipped with optimized standard test items for LED driver testing (lighting & TV backlight). The user is only required to define the test conditions and specifications for the standard test items to perform the test.
-
product
CDM Test System
1100-CDM series
Tokyo Electronics Trading Co., Ltd.
Model 1100-CDM is the latest model developed as a successor to the conventional CDM-550, and supports testing methods (Field-Induced CDM) that conform to international standards. In addition, a camera and a high-accuracy robot can apply CDM stress to a precise position.
-
product
Stationary Meter Test Systems AC
Today Meter Test Technology is much more than only testing accuracy and functionality of a conventional electricity meters. With implementation of SmartMeters a complex test and data management system is required. – It’s a good thing to have experts by your side.
-
product
Automated Test Systems
Chroma Systems Solutions, Inc.
From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
product
Camera Test System
FS 8681 / SR
FS8681/SR is software for evaluating images* and making pass/fail judgments in camera mass production inspections. It consists of the "Editor FS8681" application that sets the inspection content and the "Sequence Runner FS8681SR" application that executes the set inspection.
-
product
Universal Testing Systems (Up to 600 kN)
5980 Series
Instron 5980 Series floor model testing systems are universal, static testing systems that perform tensile and compression testing; and also perform shear, flexure, peel, tear, cyclic, and bend tests. The 5900 Series are engineered for precision, built for durability, and offer the flexibility for changing requirements. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. 5980 Series floor models are robust, heavy-duty frames commonly used for testing high-strength metals and alloys, advanced composites, aerospace and automotive structures, bolts, fasteners, and plate steels. Frames are available in load capacities of 400 and 600 kN.
-
product
Phase Noise Test System
PN9000 System
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
product
Six-Cell Diffusion Testing System
Phoenix DB-6
The Phoenix DB-6 (six-cell diffusion block) provides an ideal platform compliant with 21 CFR Part 11 for release-rate testing of six vertical diffusion cells at once using manual sampling methods. Controlled by an advanced computerized display, the DB-6 provides uniform and precise heating and stirring of six cells. The compact footprint of the DB-6 economizes on lab bench space.
-
product
Conformance Test Systems
With an established market leadership position in GCF and PTCRB approvals for LTE-Advanced and all leading-edge technologies, Anritsu continues expanding its number of test case validations in GCF and PTCRB for Protocol, RF and RRM conformance testing. With increasing complexity of wireless technologies, Anritsu Conformance Test systems provide easy-to-use control software to maximize testing efficiency.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
-
product
Cable Sheath Testing and Fault Location System
Shirla
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation
-
product
Memory Test System
T5801
Capable of Testing Ultra-High-Speed DRAM Devices, Supporting Next-Generation GDDR7, LPDDR6, and DDR6 Technologies
-
product
Cogging Test System
CTS
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
-
product
AC Hysteresis Graph Test System
DX-2012SA
Under continuous frequency of 1 kHz to 500 kHz, automatic measurement of magnetic hysteresis loop of the soft magnetic materials such as silicon steel, precision alloy, non-crystal and ferrite, accurate measurement on the dynamic magnetic characteristic parameters such as amplitude permeability µa, loss angle d, loss iron Pc, remanence Br and coercivity Hc.
-
product
Stand-alone I-V Test Systems
OAI offers a complete line of high performance I -V Testers. I -V Testers and I -V Rider software may be ordered as a stand -alone system or integrated into any OAI Solar Simulator. Three standard ranges of I -V Testers are available; ≤1A, 1 -5A, 5 -10A, and 20A. Higher current testers are available as custom options. An OAI Application Engineer will work with you to insure that the I -V Tester and I -V Rider software you choose is optimized for your specific application.
-
product
Portable System for High-Boltage Solid Dielectrics Testing
HVTS-70/50
Portable system HVTS-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
-
product
Test Tables / System Solutions
WEETECH, as a manufacturer of test equipment, offers its customers also a "Ready To Use" test system solution. It consists of the test table, the customer-specific adaptation as well as the test device, and is very quickly ready for use at the customer's site. According to the customer's requirements, the set-up is designed as a system with permanently installed adaptations for the production of constant cable harnesses in large quantities or with interchangeable adapters for the flexible production of different cable harnesses. Depending on the application, a larger table version or a smaller desk version is available. Various interfaces are available for integrating these solutions into a complete production automation system.
-
product
Manufacturing Test Only System
MTO
The MTO restricts access to test development and test files, yet enables users to run any predeveloped onTAP boundary scan / JTAG tests, including memory cluster tests and Flash programming, when activated. The MTO also provides access to ProScan, the graphical debugging environment for onTAP. Users have access to accurate pin-level diagnostics and debug features, such as the netlist browser, test reports, and low-level pin access for toggling pins, to speed up the manufacturing process and ensure accuracy.
-
product
VLF Test System
BAUR PHG 70 portable
BAUR Prüf- und Messtechnik GmbH
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
