Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
Product
High Speed Phase Inverter - Buffer
WMA-IB-HS
-
The WMA-IB-HS can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision, high speed and low noise. Because of its high bandwidth, the WMA-IB-HS model is ideal for the Falco Systems WMA-100 or WMA-300 amplifiers. It can also be used with all other Falco Systems HV amplifiers, or even with high voltage amplifiers of another brand.
-
Product
Ammeter
AC Moving Iron Meter
-
Moving-iron instruments are generally used to measure alternating voltages and currents. In moving-iron instruments the movable system consists of one or more pieces of specially-shaped soft iron, which are so pivoted as to be acted upon by the magnetic field produced by the current in coil.
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
STP Engine (IP Core)
-
The Stream Transpose® (STP) engine is a reconfigurable processor (DRP: Dynamically Reconfigurable Processor) core that combines the flexibility of software and the speed of hardware. The firmware defining processing can be reconfigured in an instant, allowing an almost infinite variety of functions to be integrated into a system. A 40nm process is currently available for ASIC.
-
Product
AC Power Sources
BPS Series
-
AMETEK Programmable Power, Inc.
The BPS Series consists of multiple high power AC power systems that provide controlled AC output for ATE and product test applications. This high power AC test system covers a wide spectrum of AC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the BPS Series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the unit to its designated location (using included casters), plug it in, and the BPS Series is ready to work for you.
-
Product
Data Acquisition & Control
Data Acquisition Module
With these DAQ systems, you can acquire and digitize signals from variety of sources and sensors, store the data, analyze it, and present the results in local and remote locations.
-
Product
Insight Product Co. Computer Vision For Assisted Driving Systems And Self-Driving Cars
-
Insight Product Company has developed a kit of algorithms for advanced driver-assistance systems in addition to optical sensors used in unmanned vehicles, integrate them into a built-in platform.
-
Product
Swept-Source OCT System
-
Santec’s Swept-Source Optical Coherence Tomography System (SS-OCT) provides a complete, flexible solution which can be used for a wide range of applications, both medical and industrial. Components can be selected to optimize the imaging speed, resolution, imaging area and depth for each application. The system is supplied with a graphic user interface (GUI) that controls the scan parameters and displays both cross sectional and 3D images. An API is available as an option, for integration with other equipment and image analysis automation. We also supports the hardware and software customization where appropriate.
-
Product
PXI 2 Amp Multiplexer, Single 32-Channel, 1-Pole
40-635A-101
Multiplexer Module
The 40-635A-101 is a single 32-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
R3
-
R3 - 19'' Rack Mountable DAQ SystemRack mountable DAQ system built into standard PC computer chassis and integrated SIRIUS data acquisition slices. Ready for simple and inexpensive upgrade of PC components.
-
Product
Hall Sensor Board with I2C Interface
056-742
-
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
sbRIO-9269, Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781120-01
Voltage Output Module
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The sbRIO‑9269 is a channel‑to‑channel isolated analog output module. The sbRIO‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes. Non-enclosed modules are designed for OEM applications.
-
Product
Analogue IC Tester
SYSTEM 8 (AICT)
-
The SYSTEM 8 Analogue IC Tester is the answer to testing analogue devices. The key feature of the AICT is its ability to functionally test all common analogue ICs and discrete devices in circuit. It is also capable of testing all types of analogue and digital components by means of the well-known, power off V-I test technique. For users requiring only the latter function, please select the Analogue Test Station section.
-
Product
“Two-Pressure” Humidity Generation System
9500
-
The Model 9500 Humidity Generator is a system capable of producing known humidity values using the fundamental, NIST proven, "two-pressure" principle. The 9500 is capable of continuously supplying an accurately known relative humidity, dew point, frost point, parts per million, or other calculated values for instrument calibration and evaluation as well as precision environmental testing.
-
Product
In-line Testing system
-
Automatical testing of electronic or automotive components and devices
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Professional Thermal Camera
FLIR T540
-
Diagnose potential faults in industrial, electrical, and mechanical systems, or discover temperature anomalies in R&D testing with the 464 × 348 resolution FLIR T540. This portable, ergonomic thermal camera offers advanced features like 1-Touch Level/Span and continuous laser-assisted autofocus, making it the perfect non-contact diagnostic tool for condition monitoring and research applications. Streamline electrical/mechanical surveys, troubleshooting, and repairs with Inspection Route mode, which runs pre-planned routes created in FLIR Thermal Studio Pro (Route Creator plugin required) so users can record temperature data and imagery in a logical sequence. The built-in Macro Mode allows R&D users to quickly switch from wide angle to close-up analysis without changing the lens. When coupled with Research Studio software, the T540 helps engineers assess unexpected hot spots and find potential design flaws. The T540 also features FLIR Ignite for automatic uploading of images directly from the camera to the cloud for easy, secure storage and sharing. The purchase of a T540 camera includes a 3-month subscription to FLIR Thermal Studio Pro and FLIR Route Creator.
-
Product
Portable Appliance Tester
PAT-10
-
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Configuration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (Pat) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplified set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
Product
Oil Tan Delta Tester / Tester System
-
The instrument is designed to test the insulation resistance of electronic and electrical components in the range of 1 Meg ohm to 10 Million Meg ohm.
-
Product
NVIDIA® Jetson Nano™ Edge Inference Platform
DLAP-211-Nano
-
- Deep learning acceleration with NVIDIA® Jetson Nano™- Compact fanless system 148(W)x120(D)x49.1(H)mm- Wide temperature range from -20°C to 70°C
-
Product
Manual Fixture Kit
230352 – CMK-03
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Industrial Protection
-
Schweitzer Engineering Laboratories, Inc.
Industrial protection solutions provide complete protection for low- and medium-voltage systems. Using these devices helps you avoid expensive equipment damage and failure while maintaining system performance and increasing availability. They can easily coordinate with other devices in industrial- and commercial-scale petrochemical, metals and mining, and water and wastewater facilities as well as data centers, hospitals, universities, and more.
-
Product
Flex Conveyor
-
The QuickShip Flex Conveyor is a fully-functional, adjustable metal detector conveyor systems that comes standard in a variety of aperture heights, belt speeds, and belt lengths. Through LOMA’s QuickShip™ program we guarantee certified inspection systems when you need them. This system is designed to meet unique operational needs without the lead time of a custom-built system.
-
Product
Single Mode & Multimode Testing Kit
KI-TK076
-
Single mode & multimode testing kit with an optical power meter and light source for low to medium test volume on SM and MM systems.
-
Product
Time Domain Reflectometer (TDR) Card
PCI-3127
-
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
Product
Connector Blocks for Interfacing to Ribbon Cables
-
VI Control Systems has designed several connector blocks for mating ribbon cables to screw terminals. Our design goal was to make the connector blocks small and inexpensive. Connector blocks are mounted by using 6-32 stand-offs. The connector blocks feature a ground plane that is connected to the mounting screw holes.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm
50-293-014
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 52.4kΩ
50-297-033
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
Amplifier
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
Product
Video System Controller for Avionics Displays
DP-VME-5400
-
DP-VME-5400 is a Video System Controller for Avionic Displays. It is a VME-based I/O module mainly used to perform video switching and video conversion operations. Applications for this board include display control in air-borne operations and redundancy control.
