Insertion Loss & Return Loss
-
Product
Optical Loss Test Set (OLTS)
MaxTester 940/945
-
First tablet-inspired, multifunction optical loss test set (OLTS) delivering insertion loss, optical return loss and fiber length measurements at two wavelengths in five seconds via fully automated bidirectional FasTesT™ analysis. With its step-by-step reference wizard and intelligent fault diagnosis, the MAX-940/945 provides expert guidance throughout the test process to ensure immediate efficiency by first-time users while removing risk of errors or negative loss—a common source of issues when testing low loss fibers.
-
Product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
21-Ch 6A-250VA 2-Bus Fault Insertion
YAV90077
Fault Insertion Unit
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Optical Loss Testing
-
Is to inject a known level of light in one end and measure the level of light at the other end, using an OLTS. The difference between source and receive power levels is the loss.
-
Product
Advanced Loss Tester
OLT-55
-
ated with Stabilized Laser Source, Optical Power Meter, Optical Loss Tester, ORL Tester and Length Testing functions. It can perform automatic bidirectional loss test on single fiber with Pass/Fail assessment. With rich functions, flexible configuration and excellent user friendly design, OLT-55 is the ideal optical loss tester to completely evaluate the optical fiber link condition in FTTx, LAN and CATV network.
-
Product
Dielectric Loss Tangent and Transmission Attenuation Measurement System
RTS03
-
RTS03 measures relative permittivity (dielectric constant), dielectric loss tangent in the frequency range between 5GHz and 26.5GHz based on a correlation between measurement frequency and transmission attenuation as the microwave passes through the flat plane sample.
-
Product
SM & MM Quad Optical Loss Test Set
KI2724-INGAAS
-
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber optic systems at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it is a powerful fiber optic multimeter / OLTS with improved test flexibility and productivity.
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
-
Product
Fluid Loss
-
Fluid Loss testers were designed to be as easy to use as possible, with clear and intuitive controls. Once the cement slurry or mud is placed into the test cell, a programmable temperature controller increases the temperature at the desired rate.
-
Product
Low Loss Combiners
-
*Tunable or band specific low loss combining of Tx and Rx*Typical 0.7dB insertion loss*Optional second duplexer can be installed in the same tray*High power handling with low IM and insertion loss*AISG 2.0 compliant
-
Product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch, N/O Through Relays
40-190B-302
Fault Insertion Unit
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Two-Way Optical Loss Test set
KI23403OLV-INGAAS-APC
-
A Dual Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on multimode fiber at 850 / 1330nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. A multimode APC connector on this model is required for reliable ORL test performance.
-
Product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Diesel Return Flow Sensor
TP-RFS400
-
Common Rail Diesel injection systems are becoming more and more advanced. The diesel return flow sensor RFS400 can be used together with a lab scope (automotive oscilloscope) to diagnose the most advanced Diesel injection systems.
-
Product
Flow Detector with Pressure Loss Compensation Function
FP-213S / FP-2140S
-
The Volumetric Flow Detector FP-213S, FP-2140S are volumetric flow detectors, used in combination with the Digital Flow Meter FM/DF series, for precision measurement of fuel flow such as gasoline, light oil and kerosene.They are suitable for those who want to evaluate the engine performance by measuring the minute flow rate of a small engine and making the fuel supply pressure as close as possible to the actual vehicle state.
-
Product
Loss Measuring System for Transformers
LiMOS
-
HIGHVOLT Prüftechnik Dresden GmbH
The transformer loss measuring system LiMOS is designed for highly accurate measurement of losses and other parameters required in the framework of routine and type testing of power transformers. The combined voltage/current sensors and the digital signal processing enable a very compact design with only one HV device per phase with smallest volume and footprint. The digitized and preprocessed signals are transmitted via fiber optic cable to the receiver unit (LiMO-MCSU).
-
Product
Single Mode Low Loss All Optical Switch From 8x8 To 192x192 Ports
SERIES 6000
-
The Polatis Series 6000 Network Optical Switch is a high-performance, fully non-blocking all-optical matrix switch available in sizes from 8x8 up to 192x192. It is designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds. With support of Software-Defined Networks (SDNs) via an embedded NETCONF and RESTCONF control interfaces, the Series 6000 enables extremely low latency for time-critical traffic required for new virtual cloud services in hybrid packet-optical data centers. The Series 6000 is based on Polatis’ patented DirectLight® optical switching technology that has been proven in the most challenging data center, telecom and defense applications and is also used by major network equipment manufacturers to automate testing of optical components and subsystems.
-
Product
Two-Way Optical Loss Test set
KI23422OLV-INGAAS
-
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber at 1310 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use.
-
Product
SM & MM Quad Optical Loss Test Set
KI2724-INGAAS-APC
-
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Product
Dielectric Loss Tangent Testing Instruments
-
Insulation materials in electrical equipment are used between a pair of electrodes; therefore it can be expressed as capacitors. Applying AC voltage to a capacitor with insulation materials causes an energy loss due to the leak current, the dielectric polarization, and the partial discharge. Because of this, the phase of the capacitor current is more delayed than that of a zero-loss current (reactive current) flowing in an ideal insulation material. The delay angle is called "Dielectric Loss Angle", and the tangent is "Dielectric Loss Tangent" (tanδ). Please refer to the technical guide explained in detail.
-
Product
Quad Optical Loss Test Set
KI27624-INGAAS
-
A Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber optic systems at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful optical multi-meter style solution to improve test flexibility and productivity.
-
Product
Insertion Flow Meter
SPI Mag
-
The SPI Mag Insertion Flow Meter provides a highly cost-effective solution for the accurate measurement of liquid flow in closed conduit, pressurized pipe applications. Unlike conventional magnetic meters, the SPI Mag's cost is independent of pipe size.
-
Product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Digital Program Insertion Auditor
Torque DPI
-
The DPI Auditor supports the ANSI/SCTE 35 2001 standard that defines a fully digital mechanism to control remote splicing equipment via cueing messages embedded in the transport stream. The core of the standard is centered on an SIT (Splice Information Table) which can contain a schedule message or an insert message.
-
Product
Two-Way Optical Loss Tester
KI23403OLV-INGAAS-APC-50U
-
A Two-Way Optical Loss Tester (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on multimode fiber at 850 / 1330nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. A multimode APC connector on this model is required for reliable ORL test performance.
-
Product
Channel Insertion & Encoding
-
ATX’s encoder products provide a cost-effective and space-efficient solution for digital transmission and/or insertion applications. ATX’s fully integrated wall or rack mount “single unit” line of products are ideal for inserting security camera video into MDUs, inserting barker or information channels into hotels and other commercial properties, for digital simulcast applications, and for digital delivery of PEG or hub site specific programming.
-
Product
Two-Way Optical Loss Test Set
KI23427OLF-INGAAS-APC
-
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber with an APC connector at triple 1310 / 1490 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. The 650 nm VFL is on a separate port.
-
Product
MX Series - i2 Modular Inserts
-
VPC i2 MX inserts offer standard and hybrid transmission options for both wired and PCB solutions.
-
Product
VTAC Vertical Header Insert
-
The VTAC vertical header insert is designed to mount on custom PCBs. Can be configured as a backplane connector and daughterboard connectors. Also sold as a set under 610151108.
