Charge Sensitive Preamplifiers
See Also: Detectors
-
Product
Smart Refrigerant Charging Kit
HUB4
-
UEi Test & Measurement Instruments
The HUB4 gives the ability to wirelessly get Vapor and Liquid pressures via the WPP1 probes and Vapor and Liquid temperatures via the WPC1 probes, all via the free UEi Hub App. Easy to use and a rugged design make the App and probes an excellent addition to any technician's toolbox.
-
-
Product
Programmable Current Preamplifier
99539
-
The Model 99539 is a modular, multi-channel current preamplifier with parallel, logic level, gain control input. It consists of circuit boards which plug into a 3 1/2" high by 19" wide rack chassis.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
Charge Plate Monitors
-
Our charge plate monitors the voltage of the battery and the voltage of the battery.
-
Product
Low Noise Preamplifier
-
The UPL-3001 preamplifier is a high performance solution for the low-noise amplification of ultrasonic signals. Designed for signals ranging from 0.5 to 300 MHz, the small and lightweight, rugged unit is perfect for remote applications. This is ideal for P&C, TT, AUT or TOFD inspection.
-
Product
16 Channel Charge Integrating ADC
CQ16
-
The CQ16 is a 16-channel 12bit, fast converting charge-integrating ADC for CAMAC. To provide compatibility to older CAMAC ADC’s it can be switched into an 11-bit mode. All data read-out is provided either via CAMAC commands or through the fast FERA bus on the front of the module.
-
Product
Low Noise Differential Preamplifiers
-
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
Product
Microphone Preamplifier
426A05
-
Preamplifier for 1/4" side vented prepolarized microphones.
-
Product
12V Auto Battery And Charging System Analyzer
1947
-
Peaceful Thriving Enterprise Co Ltd
1. Check for batteries, regulators and alternators. 2. For all 12V system vehicles, with LED indicator that helps pinpoint problems for fast troubleshooting. 3. Other car battery testers are also available.4. With CE Approval.
-
Product
Time Sensitive Networks
-
Time Sensitive Network (TSN) standards enable deterministic real-time communication over Ethernet, allowing solutions to be built to provide extremely precise, predictable timing and control across the network. By adding features to Ethernet such as time synchronization, ingress policing, seamless redundancy, frame preemption, scheduled traffic, and stream reservation, TSN ensures data is not delayed by the network.
-
Product
Preamplifier
-
The UBBV series are external, extremely low-noise broadband preamplifiers that can be mounted to any SPECTRAN spectrum analyzer. They are ideally suited for spectrum analyzers and oscilloscopes as well as antennas of all manufacturers and are supplied with extensive accessories.
-
Product
Battery Charge Discharge Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Charge Discharge Tester is a multi-function comprehensive tester which is not only a battery charger and Battery discharger, but a battery activator.
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Thermal Sensitivity Tester
NTE-2A
-
The NTE-2A Thermal Probe is a sophisticated, non-invasive device for the clinical evaluation of neuropathy and the assessment of short fiber neurological function. Individual thresholds are compared to normals to statistical normals. These results provide an accurate means of tracking chronic changes in small fiber nerve function. It can be used for pain studies and in any application were a variable, accurately-controlled temperature stimulus is required. The NTE-2A is often used in conjunction with the Vibratron II to assess peripheral neuropathies.
-
Product
Current Preamplifier
1641
-
The Model 1641 Current Preamplifier is a simple low cost wideband gain block for use with photomultipliers
-
Product
Battery Charge And Discharge Test System
9841
-
*Easy user interface*Measure Voltage, Current, Power, KWH, AH, Temperature, Reference Voltage*Accuracy Measure Time*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery. *The test result will be stored to ACCESS data
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
-
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
Product
In-line ICP® Charge Converters
-
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
Product
High Current capacity testing from Intelligent Charging
CT75A
-
A UK-based helicopter manufacturer wanted high capacity testing capability for their helicopter batteries and came to Intelligent Charging for a Special Unit. As a result of the above requirement, Intelligent Charging designed and built this new capacity testing unit to add to our extensive range of intelligent battery charging and capacity testing products. With up to 100.0A capacity testing capability this model will satisfy the most demanding aviation battery.
-
Product
USB Preamplifier, 100 MHz to 26.5 GHz
U7227C
Amplifier
The U7227C, 100 MHz to 26.5 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
Radiometer Spectral sensitivities precisely adapted to the measurement task
UVS-B-T
-
Compared to the spectral response of the UVS-E, the UVS-B-T has a sharper cut-off at the transition from UV-B to UV-A. This feature reduces the UV-A contribution to the radiometer output and permits the highest possible correlation to atmospheric UV-B irradiance.
-
Product
High Sensitivity Shock0 to 5g
TGP-0605
-
The TGP-0605 measures low level impacts and can be used for machine condition monitoring and the monitoring of expensive and/or fragile shipments.
-
Product
USB Preamplifier, 2 to 50 GHz
U7227F
Amplifier
The U7227F, 2 to 50 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
Space Charge Measuring Equipment
PEA
-
The increasing request for energy quality and, thus, insulation system reliability, associated with significant steps in the manufacturing of new insulating materials, are pushing strongly the research on new techniques for the diagnosis of insulation ageing.
-
Product
Dual Digital Aquisition System For Charge Integration And Pulse Shape Discrimination
DT5790
-
The DT5790 operates upon the DPP-PSD firmware, specially developed for Charge Integration and Pulse Shape Discrimination. DPP-PSD is based on an advanced on line Digital Dual Gate Charge Integration allowing an effective data analysis even at high count rate. It performs input signal baseline calculation, self-triggering and double-gate charge integration with programmable parameters, double integration of both prompt and total charge for Pulse Shape Discrimination and pedestal subtraction for energy calculation.
-
Product
External Pre-amplifiers
-
Although all Spectrum A/D cards have a very powerful input section with a highly configurable input amplifier and a variety of input ranges it is sometimes necessary to have additional external amplifiers if the signal to acquire has an extremely low level. Spectrum offers a range of perfectly matching external amplifiers to cover such cases. These powerful amplifiers have been rated using the Spectrum cards and offer best performance together with high amplification rates.The amplifiers are simply connected between the signal source and the Spectrum A/D card input and can be manually switched between different settings using small lever keys. All amplifiers allow the offset compensation by using an adjustable screw.
