Signal Conditioning
The processing of signals to reduce noise level, amplify, attenuate, or otherwise condition.
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Signal Conditioning Modules
-
Signal conditioning modules provide signal conditioning on a per-module basis for various types of sensor or signal.
-
Product
Portable Signal Conditioning System
SCS-800
-
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.
-
Product
Signal Conditioning & Control
-
Offering a wide variety of products from amplifiers and comparators to redrivers, microcontrollers, data converters (ADC) and digital potentiometers (POTs).
-
Product
Signal Conditioning and Filtering
MSXB 067
-
The MSXB 067 Signal Conditioning Expansion Board provides analog signal conditioning for strain gauges, load cells, RTDs, and other resistive sensors. MSXB 067 provides a flexible interface for quarter-bridge, half-bridge, and full-bridge sensors, with two to six wires for each sensor, with or without voltage sense feedback. A small daughterboard supports user-supplied bridge completion resistors.
-
Product
General Purpose Signal Conditioning Instrumentation
-
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements.
-
Product
RTM Actuator Signal Conditioning Board
MS 3630I
-
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
Sensor Signal Conditioning System
SCS
-
SCS Sensor Signal-Conditioning System complements the iDSC 1816 anti-aliasing board to provide a continuous path in a single package: starting with raw measurements at the sensor and ending with conditioned anti-aliased data logged to disk on a PC.
-
Product
PXI Signal Conditioning
-
For RF and Microwave measurements, Keysight PXI signal conditioning modules modify an analog signal to meet the requirements of the next stage for signal processing. Signal conditioning examples include amplification, attenuation, converting and filtering.
-
Product
Analog Signal Conditioning &Isolation Products
DSCIA
-
DSCIA module is a signal channel isolated analog input or output.
-
Product
Charge Amplifiers & Signal Conditioning
-
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
Product
Signal Conditioning System
SCS-801
-
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.The SCS-800 takes advantage of the increasing capabilities of notebook and desktop PCs by leveraging off the PC's strengths. It provides a high-performance, flexible solution whether used as a conditioning front-end for desktop systems in the factory or as a mobile solution for portable systems in the field.
-
Product
Signal Conditioning and Filtering
MSXB 065
-
The MSXB 065 Signal Conditioning Expansion Board provides filtered analog signal conditioning for voltage signals for Data Acquisition Processor systems. Each board has differential inputs; jumper-selectable simultaneous sampling; jumper-selectable gains of 1, 5, and 25; fourth-order anti-alias filters, cutoff frequencies from 100 Hz to 50 kHz.
-
Product
Signal Conditioning
-
Mantracourt’s analogue output strain gauge signal conditioning modules offers a flexible solution for any analogue requirement.
-
Product
Signal Conditioning
-
The output of an inductive (magnetic reluctance) speed sensor is an alternating voltage in which both the frequency and magnitude depend on target speed. The TTL Interface Adaptor converts this voltage into a TTL logic signal whose frequency corresponds to tooth passing frequency. The magnitude of the output signal from the interface is independent of the tooth passing speed.
-
Product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 5716
-
The ProDAQ 5716 is a 1U high rack-mountable signal conditioning box for standard 19 in. racks. It provides signal conditioning for up to 16 strain gage or ICP sensors. Either one ProDAQ 3416 16-Channel ADC Function Card or up to two ProDAQ 3424 8-Channel 24-bit Sigma-Delta ADC Function Cards can be connected to the unit.
-
Product
Signal Conditioning With SLSC
-
Switch Load and Signal Conditioning standardizes the "last mile" between the measuring device and the device under test (DUT) in hardware and software. SLSC is a modular extension for data acquisition products such as PXI and CompactRIO.
-
Product
Signal Conditioning and RF Distribution
-
CAES provides high performance signal conditioning and RF distribution solutions such as switch matrices for the EW, missile, radar, communications and space markets. Our custom designs offer high speed switching, low insertion loss, low harmonic level and excellent isolation.
-
Product
8 Channel Sample & Hold and Signal Conditioning Board
-
Same features of 8 Channel Sample & Hold and Signal Conditioning Board plus connection and transient protection for Group3 B (digital) and D (analog output) boards.
-
Product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
-
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Product
16-Channel RTD Signal Conditioning Card
ProDAQ 5821
-
The ProDAQ 5821 series of Signal Conditioning Cards is designed to interface with a variety of sensors, principally RTDs, Thermistors, Cryogenic Diodes and Voltage type sensors. Each version of the 5821 provides the capability of precise 4-wire measurement. In order to achieve this, a precise 500μA constant current source is provided per channel. The current source can be disabled on a per channel basis and is monitored to ensure that current is flowing. The value of the output current is stored on-board after calibration. In order to achieve the highest accuracy the output current may be automatically calibrated 'on-the-fly' using the ProDAQ 3416 24-bit Sigma-Delta ADC card and an on-board precision resistor.
-
Product
IEPE Signal Conditioning Amplifiers
-
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
-
Product
Signal Conditioning
-
Sensors that are used to collect the data from the environment often don’t produce signal of characteristics optimal for an analog to digital converter (ADC) to translate to digital data. Additionally, these signals can be subject to electromagnetic interference (EMI) that introduces noise, having a negative impact on the reliability of the data. To make this analog input readable for the processing unit and dependable enough to give the desired quality of data the signal has to undergo a process of signal conditioning.
-
Product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
-
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
-
Product
Signal Conditioning Instrumentation
-
Columbia Research Laboratories
Columbia offers a wide variety of Signal Conditioning Instrumentation for a variety of Sensor types. These range from Laboratory as well as Airborne Charge Amplifiers, Differential Charge Amplifiers, In-Line Charge Converters, Constant Current Power Supplies and ICP Compliant Amplifiers all in support of Columbia's extensive Piezoelectric product line. Additionally Columbia offers unique Strain Gage Instrumentation Amplifiers which provide built in auto zeroing of gage offset voltages which can increase typical measurement accuracies. These robust Signal Conditioning products have been flight qualified on many current military aircraft and missile programs and are now available for your distinctive program needs.
-
Product
Signal Conditioning
-
To get most out of high-quality sensors, accurate, low-noise processing of the sensor signals that are emitted is essential. Kistler offers an attractive portfolio of solutions for signal processing and subsequent data digitization. Piezoelectric (PE) sensors with a charge output require a so-called charge amplifier. On the other hand, piezoelectric sensors with integrated electronics (IEPE) are supplied by Piezotron couplers which decouple and amplify the signal.
-
Product
PXI-6280, 16 AI (18-Bit, 625 kS/s), 24 DIO, PXI Hybrid, Multifunction I/O Module
779120-01
Multifunction I/O
16 AI (18-Bit, 625 kS/s), 24 DIO, PXI Multifunction I/O Module—The PXI‑6280 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Bit Error Rate Tester
iBERT Series
-
Provide a range of signal conditioning and BER analysis from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry''s broadest serial communications test portfolio of bit error rate tester products.
-
Product
Data Acquisition and Control System
DAQ 7000
Data Acquisition System
data acquisition and control system that provides connectivity, signal conditioning and modular I/O for variety of sensors or signals, and it is an ideal DAQ for field deployment.
-
Product
PCI-6284 , 32 AI (18-Bit, 625 kS/s), 48 DIO PCI Multifunction I/O Device
779110-01
Multifunction I/O
32 AI (18-Bit, 625 kS/s), 48 DIO PCI Multifunction I/O Device - The PCI‑6284 offers analog input, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Accelerometers
-
Analog Devices accelerometers and iSensor® MEMS accelerometer subsystems provide accurate detection while measuring acceleration, tilt, shock, and vibration in performance driven application. Our portfolio leads the industry in power, noise, bandwidth, and temperature specifications, and offers a range of MEMS sensor and signal conditioning integration on chip. Our MEMS-based Circuits from the Lab® reference designs have been built and tested by ADI experts to help you jumpstart your next system design.
