Test Probes
See Also: Probes, Microprobes, Probe Cards, RF Probes, Test Fixtures, Test Heads
-
product
SINGLE ENERGY IMPACT HAMMERS
Shenzhen Chuangxin Instruments Co., Ltd.
It’s used to test the mechanical integrity of product enclosures and check the durability of enclosures for electrical appliances of other electrical appliances and other electronic products. If damage occurs from the Impact Hammer test, accessibility probes can be used to measure the extent or severity of the damage. The Impact Hammer simulates the mechanical impact to which electrical equipment maybe subjected.
-
product
30 AMP Fuse Buddy Testers
FB305M
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
product
2.5mm Test Rod Test Probe Needle
CX-4C
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test rod test probe needle Used to verify the protection of persons against access to hazardous parts.
-
product
3-48V Auto Tester
1960A
Peaceful Thriving Enterprise Co Ltd
Check on 3-48V systems. Especially suitable for the control of electrical and electronic parts of motor vehicles, for the fault finding on components. The tester is connected with a banana plug adapter, including a testing probe and an alligator clip.
-
product
THRU HOLE BARE AND LOADED BOARD TEST PROBES
SERIES 80
MAXIMUM CURRENT: 6 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver with 24 Kt goldplated ID and OD over nickelSPRING: (Standard) Beryllium copper,silver plated. (-1) Stainless steel,silver plated
-
product
Standard 1.08 (31.00) - 3.50 (99.00) General Purpose Probe
EPA-2D
Current Rating (Amps): 5Average Probe Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64Resistance (mOhm): 35
-
product
Test Fingers & Probes
Test Fingers and Probes are used in most standards to check accessibility to moving parts or hazardous live parts. They comes in many forms, such as test fingers, test rods, test balls etc.
-
product
Ingun Spring Probes
MicroContact AG offers the assortment of test probes and test adapters from Ingun as a Swiss representative.
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 43
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
product
Flying Probe Programming & Test Development
Testing House offers full Flying Probe Programming and Test Development using its very own Seica Pilot LX Flying Probe Test Stations.
-
product
Terminal Test Kit (92 Pcs)
3601C
Peaceful Thriving Enterprise Co Ltd
*Total: 92 pcs*Alligator clip x 2 pcs*Testing probe x 2 pcs*Flat terminal x 48 pcs*Testing needle x 4 pcs*1 to 2 connector x 2 pcs*Round terminal x 24 pcs*5K variable resistor x 2 pcs*Polarity tester/stroboscope x 2 pcs*SRS air bag replacement connector x 2 pcs*Male / Female to Male / Female Extension Wire x 4 pcs
-
product
CAPACITANCE METER
C350
This is a high quality digital capacitance meter. Check the accuracy and status of capacitors up to 20mF, a very handy tool for virtually any technician. It features high accuracy (0.5%) and 9 selectable ranges. A zero adjustment knob is also provided to "zero" test lead capacitance. Includes test probe set and yellow rubber boot.
-
product
Cleaner for Test Probe
EQOmat
We have developed EQOmat, a cleaner exclusively for test probes that removes dust such as flux and solder debris adhering to the tip of the test probe. The structure and thinness built with the user's convenience in mind are important items that have sufficient functionality and are indispensable for long-term use of the probe. * EQOmat is an abbreviation for Ecological Qualified Octopus Mat.
-
product
Robotic Probing of Circuit Cards
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
product
Short Test Pin Probe
Probe 13
Shenzhen Chuangxin Instruments Co., Ltd.
Short Test Pin Probe 13 The model CX-13 short Test Pin Probe is used to test for accessibility of small objects and meets IEC, CSA and UL requirements.
-
product
Probe Card Analyzers
PB3600
The PB3600 provides the latest techniques in testing and maintaining probe cards. Designed through joint development with many of the world’s largest semiconductor and probe card manufacturers, ITC has produced an ergonomic analyzer with the greatest measurement resolution, highest throughput, most flexibility and still made it easy to use.
-
product
Test Probes & Clips
CF Instrument Accessories Ltd.
CF Instrument Accessories Ltd. Test Probes & Clips
-
product
Digital Megohmmeter Test Kit
STME-RT1000F
Statclean Technology (S) Pte Ltd
This is a Resistance-Resistivity-Humidity-Temperature Test Kit. It is easy to operate, compact, lightweight, portable meter designed to measure temperature, humidity, and electrical resistance/resistivity. It has both internal and external test probes. The meter will measure resistivity, resistance between two points, and resistance to ground according to EOS/ESDAssociation Standards, -S4.1, S6.1, S7.1, S11.11, and European Standard CECC-EN 1000/15.
-
product
Accessibility Probe
Shenzhen Chuangxin Instruments Co., Ltd.
Temperature test probe surface temperature probe
-
product
Test Hook Probe
CX-S11
Shenzhen Chuangxin Instruments Co., Ltd.
Test Hook Probe Used on enclosures prior to accessibility testing. The test hook is ¨hooked〃 into vents and seams in the enclosure & then pulled with a force (usually 20N).
-
product
Energized Cable Sensor
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
product
PRO Test Lead Kit
142
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
product
Gaussmeter
DX-105
DX-105 Gaussmeter is a desktop gaussmeter. Which is based on the latest progress of the Hall Effect magnetic field measuring instrument.Adapt the high stability constant current source circuit technology to design and manufacture. Test probe adapts imported GaAs linear Hall-chip, the difference between any two probes is small, which can be replaced directly when it is damaged. DX-105 Gaussmeter is an ideal DC magnetic field test instrument.
-
product
Test Probes
A physical device used to connect electronic test equipment to a device under test (DUT).
-
product
Hardness Testers
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
product
CAM/TRAC Test Kits
Series 47
The VP Series 47 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 47 provides interface compatibility using the Virginia Panel ITA G12 interface. The ITA frame is offered as an option for those wanting to provide their own ITA Interface.
-
product
CAT III Digital Multimeter
82600
Measures AC/DC voltage/current up to 600V and 10A, capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and an operating temperature range between -40° to 1000°C. Features manual or auto shutdown after 15 minutes of inactivity, protection against overload at all ranges, data hold, low battery indicator and warning alarm. Also includes a LED flashlight for low light situations. Rubber outer case adds protection against drops and a stand bracket to hold meter at viewing angle and test probe holding clips.
-
product
Test Probes
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
product
Wafer Probe Test System
STI3000
The STI3000 is a wafer-level MEMS and mixed signal ASIC probe test system that combines several functional STI test equipment blocks for testing gyros, accelerometers, pressure sensors, microphones, resonators, and mixed signal ASICs.
