Test Probes
See Also: Probes, Microprobes, Probe Cards, RF Probes, Test Fixtures, Test Heads
-
product
Voltage Probe
KHZ43201
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
product
LOADED BOARD TEST PROBES
SERIES-70
ElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35mA test current70 18 mOhms mean73 60 mOhms mean74 40 mOhms meanMaterials and FinishesPLUNGER: Heat treated beryllium copperor steel hardened to 55-60RC70 24Kt gold plated over nickel73 24Kt gold plated over nickel74 Rhodium plated over nickelBARREL: Nickel silver70 24Kt gold plated ID and OD over nickel73 No Finish74 24Kt gold plated ID and OD over nickel
-
product
6 Sided Bed of Nails Testers
BoxProber Family
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
product
Topside Probing In-Circuit Test Fixtures
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
product
Pilot V4
The Pilot V4 Next series is a full-performance, double-sided, flying probe test system with an extremely high level of flexibility, making it the ideal solution for those with a wide variety of testing needs.
-
product
Test Probes
Petracarbon is a leading supplier and provider of spring contact probes and semiconductor test sockets.
-
product
Boundary-Scan Interactive Analyzer & Toolkit
ScanExpress JTAG Debugger
Test probe access is a luxury—modern electronic system design techniques such as blind and buried vias or ball-grid-array (BGA) devices guarantee limited signal access. Test points quickly reduce precious board real-estate and can even degrade performance. ScanExpress JTAG Debugger overcomes these limitations to provide the control and visibility necessary to quickly debug and test hardware, using a simple JTAG port to interface with IEEE-1149.1 compliant devices.Whether debugging prototype hardware, enhancing production tests with boundary-scan control, or diagnosing a faulty board in the field, ScanExpress Debugger’s easy-to-use and versatile interface helps engineers test and debug systems faster and more efficiently.
-
product
Battery Probes
C.C.P. Contact Probes Co., LTD.
CCP offers a variety of different high current battery testing probes.
-
-
product
LUTHER & MAELZER BARE AND LOADED BOARD TEST PROBES
SERIES LMP 60
MechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver, 24 Kt goldplated over nickel
-
product
Photonics Test Solutions
Chroma offers precision instruments such as laser drivers, photodetector monitoring, and temperature controllers. These lab class instruments are often intefrated into production solutions for wafer probe test, burn-in and device or module characterization with inspection, metrology, robotics, Industry 4.0 and more.
-
product
Environmental Test Probe, PH, Tenma 72-6783 PH Meter
72-6784
The 72-6784 is a typical 0 to 14pH Probe with epoxy body, BNC connector. It is used with pH meter 72-6783 model.
-
product
Benchtop Test System
300 Series Benchtop ATE
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
VX4 System
PrecisionWoRx
The PrecisionWoRx VX4 System gives test facilities and probe card manufacturers the ability to confidently test tighter pitches and smaller probe tips. The system can be easily configured to specific requirements for a variety of probe card technologies. For processes using cards with very small probe tips, the system’s high-resolution optics deliver a detailed field-of-view for high accuracy and repeatability.
-
product
Board Test Fixture Probes
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
product
Rugged Connectors
Guaranteed for a minimum of 100,000 connections, our rugged connectors are designed to meet your industrial & ergonomic demands in harsh testing environments. We offer numerous connector specifications all fitted with interchangeable spring loaded test probes. Supplied as a single hand held unit, panel mounted or fitted to a test lead, the combinations are limitless. Designed directly from your CAD data and thoroughly tested, our rugged & reliable connectors are used worldwide on a daily basis.
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 33
ElectricalMAXIMUM CURRENT:3 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,20 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24Kt gold plated over nickelBARREL: Nickel silver with preciousmetal clad ID.SPRING: Music wire, silver plated
-
product
Deluxe DMM w/Amp Shutters
582
*Huge 2 inch LCD Display, easy to see from across the room *Display is backlit for use in Dark Spaces *Amp Shutters prevent mistaken operation, improve safety and saves fuses by blocking unused amp jacks! *Great Meter for Electrical Trouble Shooting *11 Test Functions, 33 Test Ranges *Measures Temp in Both F and C, Probe Included *Desireable 20 Amp Test Range *Modern Design, the Protective Holster is Built-In *Data Hold *Carrying case, Test leads, Temp probe, Instructions and Battery included
-
product
Advanced High Speed Test Probe
SQprobe
SQprobe® is an advanced high speed probe designed for emerging software defined (SDN) and virtualized networks. It monitors IP based voice, video, audio and data streams at Gigabit rates, performing deep packet inspection (DPI) and providing accurate and detailed real time service quality metrics, usage and demographic data.
-
-
product
2.5mm Test Wire Test Probe Pin
CX-3C
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test wire test probe pin 1.Application: Used to verify the protection of persons against access to hazardous parts. Also used to verify the protection against access with a tool.
-
product
FEA and Strain Gauge Testing
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
product
Ultrasonic Angle Beam Probes For Weld Seam Testing
SONOSCAN W
The ergonomic angle beam probes for Non-destructive Testing (NDT) from the SONOSCAN series inspect metals for cracks and inclusions. In the metal industry they are mainly used for weld seam testing. Our SONOSCAN probes are powerful, robust ultrasonic transducers which can be connected to all standard ultrasonic testing gauges.
-
product
Electric Insulating Oil Tester
PortaTest
Portatesters are easy to use. Based on the test standard, you select the corresponding test sequence. Then, the required test probe and the electrode gap for the selected test standard is displayed. The setting gauge, included in the scope of delivery, facilitates the adjustment of the electrode gap. Afterwards you fill the insulating oil in the test vessel and close the test chamber.
-
product
Semicon Test Probes
Fine pitch, 0.20 mm [8 Mil] - single & double ended - non-rotating - kelvin - RF - high performance.
-
product
Handheld Digital Multimeter, 2000 Count, Auto/ Manual, 10 A, 250 V, 3.5 Digit
72-13430
Clear LCD Display. Equipped with comfortable protective cover, test probe holder. 2m drop test, precision protection. Auto Power Off. Auto Backlight Off. Loud Buzzer Sound. Knobs shift smoothly, in-line with ergonomics. Relative mode. Powered by AAA 1.5V x 2 batteries. 12-month limited warranty. view Terms & Conditions for details
-
-
product
Boundary Scan Test
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
product
Handheld Digital Multimeter, AC/DC Voltage, Continuity, Diode, Resistance, Temperature, 3.5, 2000
72-13435
*Clear LCD Display*Equipped with comfortable protective cover, test probe holder*2m drop test, precision protection*Auto Power Off*Auto Backlight Off*Loud Buzzer Sound*Knobs shift smoothly, in-line with ergonomics*Powered by AAA 1.5V x 2 batteries*12-month limited warranty *view Terms & Conditions for details
-
product
Test Contactor/Probe Head
cBoa
cBoa™ test contactors and probe heads are the solutions for contacting high-frequency devices for package test or final test at wafer. The robust design and materials of the cBoa probe withstand the rigors of high-volume test by providing longer life and higher yield. The homogeneous DUT side plunger provides longer run times between cleaning and increased probe life.The cBoa features a stainless-steel spring for tri-temp testing and performs in operating temperatures of -55°C to +155°C and bandwidth of up to 35 GHz @ -1 dB.
