-
Product
In-Circuit Testing
-
If you are looking for in-circuit test applications, equipment or advice, our experienced engineers can help you. Whatever your fixturing requirements or special software features, our long history of work in this field means that we have probably seen and done it before.
-
Product
Manual Fixture Kit
230372 – CMCSK-03-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
PXI 12x8 RF Matrix 250MHz 75 SMB - With Loop-Thru
40-726A-751-L
Matrix Switch Module
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
Manual Test Fixture (MA)
MA 2013/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 25,00 kg
-
Product
9025 Slide Mount
-
The 9025 Slide Mount was developed to provide maximum versatility and easy access to instrument-side wiring and cable assemblies. Ordering is simple: the 9025 Slide Mount s is offered as a package that includes the receiver, flanges and instrument bracket. The only to determine is the type of slide kit needed. VPC offers a selection of slide kits designed to fit most common rack depths. Slides are rated to support 180 lbs (81 kg) to accommodate large fixtures.
-
Product
Multi-Stage Functional Test Systems
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
Manual Fixture Kit
230352 – CMK-03
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Solar Panel Chamber
-
Specifically designed for the solar industry, these climatic chambers feature specifically designed fixtures to properly measure almost any component related to solar panels including the actual panels, grid-tied photovoltaic inverters, or photovoltaic cells and modules.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
Product
PCIe
M.2 Gen4 Socket3
-
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 3 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 3 Source and Sink devices.
-
Product
Mach Airspeed Test Fixture
TA-6055A
-
The TA-6055A is a Mach Airspeed Test Fixture built to support the testing and repair of the 2082 and 2083 series of Servoed Mach Airspeed Indicators (SMASI) used in some Boeing aircraft. These mach airspeeds are synchro driven and require a coarse and fine input for altitude and a third input for airspeed. This test fixture was designed around the test procedure and is interfaced with our TA-1001 panel which provides for two of the synchro sources and two Angle Position Indicators (API).
-
Product
9050 Rack Mount
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
Product
Receiver, G12, 12 Module, With 20" Platform, For Slide Mount (slide Kit Required)
310104334
Receiver
The 20” G12 Receiver is a slide-mounted receiver. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
Probe Holders
Model P7
-
Made from 300 series stainless steel, the P7 probe holders accept all model 407 replaceable probe tips, and are secured with a set screw. When used with the P7 Tool Holder Adapter Arm; “Z” position adjustments are easy, and can accommodate a variety fixtures and probe card holders. Designed for both high temperature (-65 to 300°C) and high electrical isolation measurements.
-
Product
EBIRST 96-pin SCSI Termination Fixture
93-016-103
-
93-016-103 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
Becker Transponder Test Fixture
TA-3400
-
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Product
Freezing Tester
-
Our Freezing Tester units are available in vertical or horizontal configurations are used to test the bending/flexing durability of rubber, plastics, synthetic leather, shoes, etc., under cold temperatures as low as -30°C or -70°C depending on the selected model. The test chambers can be equipped with a variety of flexing/bending fixtures made of stainless steel. These models conform to ASTM D 1790, and ASTM D1593 standards.
-
Product
Fixtures, Programming & Test Services
-
Comware Technical Services, Inc.
Fixtures and programming services are available for Agilent, GenRad, and Teradyne testers. Working from CAD data, a program can be created in only a few days allowing for fast and cost effective testing of your products. Engineering services are available for fixture revisions or repairs.
-
-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 197 x 114 mm (wxd)
CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
In-Circuit Test Applications
-
With decades of experience developing test fixtures, we are the recognized industry leaders for solid and reliable quality as well as our outstanding customer service. We fully support our products locally and worldwide for maintenance, repair, and ECO work. Also, 100% wiring verification is part of our Quality Control process, by utilizing automated verification machines for GenRad/Teradyne and HP/Agilent fixture.
-
Product
MMI-DVI, Fixtures with Higher Voltages
100290
-
The MMI-DVI is a good basis for fixtures with higher voltages. The MMI-DVI is made of NON-dissipative plate material and can therefore be used in the low-voltage range (up to 1000V AC / 1500V DC). The earthing package included is an important component. This is because the housing earthing, the earthing connection and the earthing test ensure that the safety standards are met. The solenoid interlock and the safety switch ensure access protection.
-
Product
Resistivity Meter
Model 2180
-
The unit is compact and lightweight. The basic system is 7″ wide by 2.5″ high and 12″ long. When measurements are needed below approximately 100 micro-ohm-centimeters, the basic system is piggybacked onto a second enclosure that houses a power amplifier with a current gain of ten. The combined unit measures 7″ wide by 5″ high and 12″ long. The combined unit weighs 11.5 pounds. Two short cables interconnect the two enclosures for powering the power amplifier and routing the signals to the fixture or four point probe. The front panel of the basic system includes a 32-character backlit LCD display and a set of function keys. An easy-to-use menu will allow access to user defined parameters such as sample thickness, sample volume, and calibration constants; upper and lower alarm limits, relative measurements, and several others.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
10-CH Pneumatics CAN
YAV90PNE
CAN Interface
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
Product
PXI Expandable 16x16 RF Matrix 50Ohm Lemo 00
45-720A-541
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
Manufacturing Test Modules
-
Manufacturing Test Module (MTM) Series instrumentation from Acroname is the platform you need to free your production testers from the burdens of validation test equipment. Mix and match modules to create a complete tester within a fixture frame, eliminating benchtop and rack equipment - all without sacrificing the robustness and reusability you demand from your equipment.
-
Product
High-Speed Trimming System
LSR-3230
-
* no fixture or probe cards on top side * 2, 4, and 6 wire test capability * touch screen operation * high performance DC electrical tester * high throughput - low running cost
